2ABBV-KEYFINDERKey Finder

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (current) 2.0 3.0 Jan-31-2012 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 3.0 TIZE INTERNATIONAL CO LIMITED. 2013-11-13 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, TIZE INTERNATIONAL CO LIMITED. hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): FCC ID: 2ABBV-KEYFINDER Key Finder, TZ-K320 We affirm that between SIEMIC and TIZE INTERNATIONAL CO LIMITED , any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Signature Xiao Ni Yang / Manager E-mail: [email protected] Phone: +86 -755-86069065 Fax: Address 4/F,No.32 Building , Xinle 3 Street, No.37, Bao an District, Shenzhen, Guangdong, 518101, China

Confidentiality Request Letter TIZE INTERNATIONAL CO LIMITED. 2013-11-13 To: Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: Permanent Confidentiality Request for FCC ID: 2ABBV-KEYFINDER We hereby request confidential treatment of information accompanying this application as outlined below: - Block diagram - Operation description - Schematic The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Xiao Ni Yang E-mail: [email protected] Phone: +86-755-86069065 Fax: Address: 4/F,No.32 Building , Xinle 3 Street, No.37, Bao an District, Shenzhen, Guangdong, 518101, China

Label & Label Location on EUT Label

Antenna Module

TRF No：FCC 15.231/A Page 1 of 21 Report No ES131024139E Shenzhen EMTEK Co.,Ltd. Building 69, Majialong Industry Zone, Nanshan District, Shenzhen,Guangdong,China www.emtek.com.cn Tel: +86-755-2695 4280 Fax: +86-755-2695 4282 Access to the World ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C REQUIREMENT T OF Key Finder MODEL No.: TZ-K320 Trademark: N/A FCC ID: 2ABBV-KEYFINDER REPORT NO: ES131024139E ISSUE DATE: November 10, 2013 Prepared for TIZE INTERNATIONAL CO LIMITED 4/F, No.32 Building, Xinle 3 Street, No.37 Bao an District, Shenzhen, China 518101 Prepared by SHENZHEN EMTEK CO., LTD Bldg 69, Majialong Industry Zone, Nanshan District, Shenzhen, Guangdong, China TEL: 86-755-26954280 FAX: 86-755-26954282 TRF No：FCC 15.231/A Page 2 of 21 Report No ES131024139E Shenzhen EMTEK Co.,Ltd. Building 69, Majialong Industry Zone, Nanshan District, Shenzhen,Guangdong,China www.emtek.com.cn Tel: +86-755-2695 4280 Fax: +86-755-2695 4282 Access to the World VERIFICATION OF COMPLIANCE Applicant: TIZE INTERNATIONAL CO LIMITED 4/F, No.32 Building, Xinle 3 Street, No.37 Bao an District, Shenzhen, China 518101 Manufacturer: TIZE INTERNATIONAL CO LIMITED 4/F, No.32 Building, Xinle 3 Street, No.37 Bao an District, Shenzhen, China 518101 Product Description: Key Finder Model Number: TZ-K320 Serial Number: N/A File Number: ES131024139E Date of Test: October 24, 2013 to November 7, 2013 We hereby certify that: The above equipment was tested by SHENZHEN EMTEK CO., LTD. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 (2009) and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.231. The test results of this report relate only to the tested sample identified in this report. Date of Test : October 24, 2013 to November 7, 2013 Prepared by : Jack Li/Editor Reviewer : June Xie /Supervisor Approve & Authorized Signer : Lisa Wang/Manager TRF No：FCC 15.231/A Page 3 of 21 Report No ES131024139E Shenzhen EMTEK Co.,Ltd. Building 69, Majialong Industry Zone, Nanshan District, Shenzhen,Guangdong,China www.emtek.com.cn Tel: +86-755-2695 4280 Fax: +86-755-2695 4282 Access to the World Ta b l e o f C o n t e n t s 1. GENERAL INFORMATION ................................................................................................. 5 1.1. PRODUCT DESCRIPTION........................................................................................................................... 5 1.2. RELATED SUBMITTAL(S) / GRANT (S) ..................................................................................................... 5 1.3. TEST METHODOLOGY.............................................................................................................................. 5 1.4. SPECIAL ACCESSORIES............................................................................................................................ 5 1.5. EQUIPMENT MODIFICATIONS.................................................................................................................. 5 1.6. MEASUREMENT UNCERTAINTY............................................................................................................... 6 1.7. TEST FACILITY........................................................................................................................................ 6 2. SYSTEM TEST CONFIGURATION .................................................................................... 7 2.1. EUT CONFIGURATION............................................................................................................................. 7 2.2. EUT EXERCISE........................................................................................................................................ 7 2.3. TEST PROCEDURE.................................................................................................................................... 7 2.4. DESCRIPTION OF TEST MODES................................................................................................................. 8 2.5. SUMMARY OF TEST RESULTS.................................................................................................................. 8 2.6. CONFIGURATION OF TESTED SYSTEM .......................................................................................... 8 2.7. DESCRIPTION OF SUPPORT UNITS .................................................................................................. 8 3. CONDUCTED EMISSIONS TEST ....................................................................................... 9 3.1. MEASUREMENT PROCEDURE:.................................................................................................................. 9 3.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ......................................................................... 9 3.3. MEASUREMENT EQUIPMENT USED: ........................................................................................................ 9 3.4. CONDUCTED EMISSION LIMIT................................................................................................................. 9 3.5. MEASUREMENT RESULT:......................................................................................................................... 9 4. TRANSMISSION REQUIREMENT ................................................................................... 10 4.1. REQUIREMENT....................................................................................................................................... 10 4.2. TEST SET-UP ........................................................................................................................................ 10 4.3. MEASUREMENT EQUIPMENT USED: ...........................................…

Text truncated - open the document above for the full version.

PHOTOGRPHS OF TEST SETUP