2ABCW-1243452Active Tag 2nd Gen

H.B. Compliance is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that indudes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988,21 U.S.C.862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits.

1 | Page HBCS Test Setup Photos Ingecom 2 | Page HBCS 3 | Page HBCS 4 | Page HBCS

RFID Gen 2 Tag, with its FCC/IC Label JTT-7 labels 1”x 0.5” printed 1 color (black) on flexo. Laminated with H1047. Top view a Slanted view – showing gloss of lamination (HVIN not updated, new label to come) The labels are made of a highly wear-resistant flexible plastic. They are self-adhesive, and are widely used on polypropylene and polycarbonate. They have been tested over wide temperature ranges: they have resisted to storage temperatures down to -80ºC for years, and can also withstand boiling water for at least three minutes. They are laminated with a polyester film that can withstand from -80ºC up to +150ºC. They are expected to last way beyond the life of the tag itself (10 years+). This information comes from the owner of the GA International, Dr. George Ambartsoumian, Ph.D., D.V.M. Roll of 1000 labels (HVIN not updated, new label to come)

1 | Page HBCS Test Setup Photos Ingecom 2 | Page HBCS 3 | Page HBCS 4 | Page HBCS

Certificates and reports shall not be reproduced except in full, without the written permission of H.B Compliance Solutions, LLC. Intentional Radiator Test Report For the Ingecom. Active Tag 2 nd Generation Tested under The FCC Rules contained in Title 47 of the CFR, Part 15.249 for RFID Operation Prepared for: Ingecom Chemin des Vergers 4 – Case postale 347 -2520 La Neuveville, Suisse Prepared By: H.B. Compliance Solutions 5005 S. Ash Avenue, Suite # A-10 Tempe, Arizona 85282 Reviewed By: Hoosamuddin Bandukwala Cert # ATL-0062-E Engineering Statement: The measurements shown in this report were made in accordance with the procedure indicated, and the emissions from this equipment were found to be within the limits applicable. I assume full responsibility for the accuracy and completeness of these measurements, and for the qualifications of all persons taking them. It is further stated that upon the basis of the measurement made, the equipment tested is capable of operation in accordance with the requirements of Part 15 of the FCC Rules under normal use and maintenance. HBCS Report # EMC_13042_1 Rev.3 Page 2 of 19 Report Status Sheet Revision # Report Date Reason for Revision Ø October 18, 2013 Initial Issue 1 March 25, 2015 Re-test 2 May 14, 2015 TCB Comments 3 May 21, 2015 Changed ANSI reference HBCS Report # EMC_13042_1 Rev.3 Page 3 of 19 Table of Contents EXECUTIVE SUMMARY ............................................................................................ 4 1. Testing Summary ........................................................................................ 4 EQUIPMENT CONFIGURATION ................................................................................ 5 1. Overview .................................................................................................... 5 2. Test Facility ................................................................................................. 6 3. Description of Test Sample ......................................................................... 6 4. Equipment Configuration ........................................................................... 6 5. Support Equipment .................................................................................... 6 6. Ports and Cabling Information .................................................................... 6 7. Method of Monitoring EUT Operation ........................................................ 7 8. Mode of Operation ..................................................................................... 7 9. Modifications ............................................................................................. 7 10. Disposition of EUT ...................................................................................... 7 Criteria for Un-Intentional Radiators ...................................................................... 8 1. Radiated Emissions ..................................................................................... 8 Emissions Tests Calculations ........................................................................ 9 Criteria for Intentional Radiators .......................................................................... 12 2. Conducted Emissions ................................................................................ 12 2. Occupied Bandwidth ................................................................................ 13 5. Radiated Fundamental Emissions ............................................................. 15 6. Radiated Spurious Emissions .................................................................... 17 HBCS Report # EMC_13042_1 Rev.3 Page 4 of 19 EXECUTIVE SUMMARY 1. Testing Summary These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with Part 15.249. All tests were conducted using measurement procedure from ANSI C63.4-2009, American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the range of 9kHz to 40GHz as appropriate. Test Name Test Method/Standard Result Comments Unintentional Radiated Emissions 15.109 Pass A/C Power Line Conducted Emissions 15.207(a) N/A Battery Powered Device Occupied Bandwidth 15.215 Pass Radiated Fundamental Emissions 15.249(a) Pass Radiated Spurious Emissions 15.249(a)(d)(e), 15.209(a), 15.205, 15.35(C) Pass HBCS Report # EMC_13042_1 Rev.3 Page 5 of 19 EQUIPMENT CONFIGURATION 1. Overview H.B Compliance Solutions was contracted by Ingecom to perform testing on the Active Tag 2 nd Generation under the purchase order number 1031. This document describes the test setups, test methods, required test equipment, and the test limit criteria used to perform compliance testing of the Ingecom, Active Tag 2 nd Generation. The tests were based on FCC Part 15 Rules. The tests described in this document were formal tests as described with the objective of the testing was to evaluate compliance of the Equipment Under Test (EUT) to the requirements of the aforementioned specifications. Ingecom should retain a copy of this document and it should be kept on file for at least five years after the manufacturing of the EUT has been permanently discontinued. The results obtained relate only to the item(s) tested. Product Name: Active Tag Model(s) Tested: 2 nd Generation FCC ID: 2ABCW-1243452 Supply Voltage Input: Primary Power : 3 Vdc Frequency Range: 2402MHz No. of Channels: Single Type(s) of Modulation: FSK Range of Operation Power: 0.00002415W (Radiated) Emission Designator: N/A Channel Spacing(s) None Test Item: Pre-Production Type of Equipment : Fixed Antenna Requirement (§15.203) : Type of Antenna: Folded Dipole (PCB) Gain of Antenna: 3.0dBi Environmental Test Conditions: Temperature: 15-35⁰C Humidity: 30-60% Barometric Pressure: 860-1060 mbar Modification to the EUT: None Evaluated By: Staff at Emerson Network & H.B Compliance Solutions Test Date(s): 03/23/15 till 03/25/1…

Text truncated - open the document above for the full version.

Test Setup Photo # 1 Test Setup Photo # 2 Test Setup Photo # 3