2ABQU-STRC1009Remote Control

SONTE Limited www.sonte.com SONTE RF Specifications SONTE RF is the power supply specially for SONTE Film and SONTE Glass with 2 separated wireless controlled outputs. It can be paired by SONTE Remote. After getting paired successfully, the two outputs can be independently controlled. CAUTION Please use and store this product at room temperature Do not expose this product to rain or wet conditions Do not throw and drop this product to avoid product damage Do not self-dismantling, repair and transform the product Do not overload the use of this product This product is in working condition, please placed in children can not touch Technique Parameters Part No: STRF2008 Input voltage: 100VAC -120 VAC/220VAC-240VAC Output voltage: 60VAC±10% Output Power: 40W Frequency: 50/60 Hz Product Parameter Product Spec: 144mm（L）*100mm（W）*62mm（H） N.W: 1.15Kg Color: Silvery White Product Features 1. The input interface adopts a separate type structure, different countries use interface line corresponding use 2. Output using can change the interface, is beneficial to the output line extension and installation 3. Power output of 40W, to meet the power demand of most STF products, 4. Using the RF control mode, avoiding the directional characteristics of the general 5. Pairing method is simple, convenient replacement and installation 6. Two spare output switch, can be output without the use of remote control 7. Using aluminum alloy shell. Increase the mechanical strength of the products. Is conducive to heat consumption SONTE Limited www.sonte.com Standard Accessories RF Transformer 1pcs SONTE Remote 1 pcs 1.5M Plug wire 1pcs 3M Cable 2pcs Pairing and cleaning Pairing: Disconnect power for 5s, and then connect again, press “1” for 5s, release, after 5s later, the SONTE Remote will work normally, “1” controls Channel 1, “2” controls Channel 2, press “ON” ,two channels will be turned on, press “OFF”, two channels will be turned off. Cleaning: Disconnect power for 5s, and then connect again, press “OFF” for 20s， The SONTE Remote will disconnect with this RF Transformer. Warranty 1. The product is warranted for 12 months from date of purchase for mechanical and electrical defects. During 12 months, repair of defects will be free of charge, except insurance, handling, transportation and incidental charges 2. Wear and tear, shipping or damaged, misused, mishandle or compatibility is not cover under the warranty 3. All of the following conditions are not eligible for the warranty: A. Damaged from all man-made factors, including non-normal working environments, or damage caused by the controller and such failures B. Privately dismantle, self-repair, modification made on the product C. Damages caused by natural disaster (such as floods, lightning, earthquakes, abnormal voltage) D. Used old condition, wear and tear, rust, or disseminated E. Doesn't belong to the company's products (such as counterfeit goods) F. Damages caused by transportation after purchasing G. Does not produce a valid proof of purchase issued by authorized dealers, no warranty card presented H. The warranty or QC seal is removed, defected or altered FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, SONTE Limited www.sonte.com may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). Caution! The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.

APPENDIX III EUT PHOTOS External Photos Photo 1 Appearance of EUT Photo 2 Appearance of EUT Photo 3 Appearance of EUT Photo 4 Appearance of EUT

APPENDIX II ID LABEL LOCATION FCC ID Location

Internal Photos Photo 5 Internal of EUT Photo 6 Appearance of PCB Photo 7 Appearance of PCB Photo 8 Appearance of PCB Integral Antenna Photo 9 Appearance of PCB

Page 1 of 31 Report No.: STT2014091524R Version: STT-FCCRF-13V01 FCC Radio Test Report FCC ID: 2ABQU-STRC1009 FCC 47 CFR Part 15 Subpart C Product： SONTE Remote Trade Name： SONTE Model Number： STRC1009 Issued for SONTE Limited Unit 1205, Cyberport 2, 100 Cyberport Road, Pokfulam, Hong Kong Issued by Shenzhen STONE Testing Technology Co., Ltd. F/6, Bldg.12, Zhongxing Industrial City, Chuangye Rd., Nanshan District, Shenzhen, Guangdong, China Tel.: +86-0755-26582862 Fax.: +86-0755-61673854 Website: www.stt-lab.org Note: This report shall not be reproduced except in full, without the written approval of Shenzhen STONE Testing Technology Co., Ltd.. This document may be altered or revised by Shenzhen STONE Testing Technology Co., Ltd. personnel only, and shall be noted in the revision section of the document. The test results in the report only apply to the tested sample. Page 2 of 31 Report No.: STT2014091524R Version: STT-FCCRF-13V01 TEST RESULT CERTIFICATION Product .................................. : SONTE Remote Applicant ................................ : SONTE Limited Address ................................. : Unit 1205, Cyberport 2, 100 Cyberport Road, Pokfulam, Hong Kong Manufacturer.......................... : SONTE Limited Address ................................. : Unit 1205, Cyberport 2, 100 Cyberport Road, Pokfulam, Hong Kong Model No. .............................. : STRC1009 Standards .............................. : FCC Part 15 Subpart C (15.231) Test Method ........................... : ANSI C63.4: 2003 The above equipment has been tested by Shenzhen STONE Testing Technology Co., Ltd. and found compliance with the requirements set forth in the technical standards mentioned above. The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Test.......................................................... : Date of receipt of test item ................................. : 2014-09-09 Date(s) of performance of test ............................. : 2014-09-10 to 2014-09-16 Test Result ............................................... : Pass Testing by : Date : 2014-09-16 (Linna Liu) Check by : Date : 2014-09-18 (Andy Huang) Approved by : Date : 2014-09-19 (Ethan Chen) Page 3 of 31 Report No.: STT2014091524R Version: STT-FCCRF-13V01 Table of Contents Page 1 . TEST SUMMARY 5 1.1 TEST FACILITY 6 1.2 MEASUREMENT UNCERTAINTY 6 2 . GENERAL INFORMATION 7 2.1 GENERAL DESCRIPTION OF EUT 7 2.2 DESCRIPTION OF TEST MODES 8 2.3 DESCRIPTION OF TEST SETUP 9 2.4 DESCRIPTION TEST PERIPHERAL AND EUT PERIPHERAL 10 2.5 EUT Exercise Software 10 3 . CONDUCTED EMISSION TEST 11 3.1 CONDUCTED EMISSION MEASUREMENT (Frequency Range 150KHz-30MHz)11 3.2 TEST PROCEDURE 11 3.3 TEST SETUP 12 3.4 TEST INSTRUMENTS 12 3.5 EUT OPERATING CONDITIONS 12 3.6 TEST RESULTS 13 4 . FUNDAMENTAL AND SPURIOUS EMISSION MEASUREMENT 15 4.1 RADIATED EMISSION LIMIT 15 4.2 TEST PROCEDURE 16 4.3 TEST SETUP 16 4.4 TEST INSTRUMENTS 17 4.5 EUT OPERATING CONDITIONS 18 4.6 DUTY CYCLE TEST 18 4.7 TEST RESULTS 22 5 . BANDWIDTH MEASUREMENT 27 5.1 LIMITS 27 5.2 TEST PROCEDURE 27 5.3 TEST SETUP 27 5.4 TEST INSTRUMENTS 27 5.5 EUT OPERATING CONDITIONS 27 5.6 TEST RESULTS 27 Page 4 of 31 Report No.: STT2014091524R Version: STT-FCCRF-13V01 Table of Contents Page 6 . DEACTIVATING TIME 29 6.1 LIMITS 29 6.2 TEST PROCEDURE 29 6.3 TEST SETUP 29 6.4 TEST INSTRUMENTS 29 6.5 EUT OPERATING CONDITIONS 30 6.6 TEST RESULTS 30 7 . ANTENNA REQUIREMENT 31 7.1 REQUIREMENT 31 7.2 ANTENNA CONNECTOR CONSTRUCTION 31 Page 5 of 31 Report No.: STT2014091524R Version: STT-FCCRF-13V01 1. TEST SUMMARY Test procedures according to the technical standards: FCC Part 15 Subpart C Standard Section Test Item Judgment Remark 15.207 AC Power Conducted Emission PASS 15.231(b) Fundamental and Spurious Emissions PASS 15.205 Restrict Band Radiated Emission PASS 15.231(a)(1) Deactivating Time PASS 15.231(C) Emission Bandwidth PASS 15.203 Antenna Requirement PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report (2)The test results of this report relate only to the tested sample(s) identified in this report. Page 6 of 31 Report No.: STT2014091524R Version: STT-FCCRF-13V01 1.1 TEST FACILITY Shenzhen STONE Testing Technology Co., Ltd. Add. : F/6, Bldg.12, Zhongxing Industrial City, Chuangye Rd., Nanshan District, Shenzhen, Guangdong, China Our laboratories are accredited and approved by the following approval agencies according to ISO/IEC 17025. FCC Registration No.: 323508 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %. A. Conducted Emission : The measurement uncertainty is evaluated as ± 3.2 dB. B. Radiated Measurement : The measurement uncertainty is evaluated as ± 3.7 dB. Page 7 of 31 Report No.: STT2014091524R Version: STT-FCCRF-13V01 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment SONTE Remote Model Name STRC1009 Additional Model Number(s) N/A Model Difference N/A Frequency Range 434.02 MHz Modulation Type ASK RF Output Power Peak: 82.19 dBuV/m @3m Average: 74.38 dBuV/m @3m Antenna Type Integral Antenna Power Source DC Power by Battery. Power Rating DC 12.0V Battery Remark More details of EUT technical specification, please refer to the User's Manual. Note: (1) This Test Report is FCC Part 15 Subpart C, 15.231 for Transmitter Equipment. Page 8 of 31 Report No.: STT2014091524R Version: STT-FCCRF-13V01 2.2 DESCRIPTION OF TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or tes…

Text truncated - open the document above for the full version.

APPENDIX IV TEST PHOTOS Radiated Emission Test Setup (30 MHz~1 GHz) (Above 1 GHz)