2ABSVEBU01EBU

Burette Unit EBU User Manual Please read this manual thoroughly in advance for the best performance of the equipment. Overseas Division: Yamawaki Bldg 9F 4-8-21 Kudan Minami, Chiyoda-ku, Tokyo 102-0074 JAPAN FAX: +81-3-3237-0537, Phone: +81-3-3239-7333 E-mail: [email protected] URL:http://www.kyoto-kem.com Factory: 56-2 Ninodan-cho,Shinden Kisshoin,Minami-ku,KYOTO 601-8317,JAPAN FAX: +81-75-691-9961, Phone: +81-75-691-4122 AN 59-***** Ver.00 Important: You must observe the following rules in order to prevent physical or property damage of yourself as well as of the others. Meaning of Symbols Warning Danger of severe injury or possible death Caution Risk of physical or property damage This symbol means Prohibition. This symbol means Mandatory. Place for Installation Use the devices indoors, and avoid a place under any of the following conditions to avoid malfunction. Caution Operation of devices with strong electric motors using common power source Near strong magnetic/electric field Corrosive gas atmosphere Under direct sun light Heavily loaded and fluctuated or near power source or magnetic field Excessive range of temperature other than specified Ambient humidity exceeding 85%RH Under vibration Location with large temperature difference Other Cautions Caution Do not attempt overhaul or repair the unit by unauthorized person except authorized by KEM. Danger of electric shock, fire or malfunction. Do not use the unit in a way other than specified. Danger of fire, electric shock or malfunctioning of the unit. Supported standards 1. FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC WARNING You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. 2. Supported IC Tag You can use the tag corresponding to the ISO/IEC18000-3 (Mode1) and ISO/IEC15693. IC Tag Maker Tag-it Texas Instrumrnts Error! Use the Home tab to apply 表題 to the text that you want to appear here. Table of Contents page 1. Preparations for measurement 1 1-1. Summary .................................................................................................................................... 1 2. Parts configuration and each function 2 2-1. Appearance and Name ........................................................................................................ 2 3. Basic operation 3 3-1. Installation and connection ............................................................................................... 3 4. Specification 4 4-1. Specification.............................................................................................................................. 4 5. Warranty and After-sales Service 5 Error! Use the Home tab to apply 見出し 1 to the text that you want to appear here. Error! Use the Home tab to apply 見出し 1 to the text that you want to appear here. 1 1. Preparations for measurement 1-1. Summary This equipment is the RFID reader-writer module of the electromagnetic induction type which can read and write data in the IC tag in a non-contact by using a frequency of 13.56MHz. It allows you to communicate with the IC tag that corresponds to the standard ISO/IEC15693, of ISO/IEC16000-3 (Mode1). RFID board Burette Unit EBU Antenna RFID IC Serial Interface Tag Top Models Communication 13.56MHz Error! Use the Home tab to apply 見出し 1 to the text that you want to appear here.Error! Use the Home tab to apply 見出し 1 to the text that you want to appear here. 2 2. Parts configuration and each function 2-1. Appearance and Name ＜Main unit＞ 1) Burette stand 2) Mounting base 3) Cover 4) Motor cover 5) Seal 6) Interface cable connector 6） 3） 4） 1） 2） 5） Error! Use the Home tab to apply 見出し 1 to the text that you want to appear here. Error! Use the Home tab to apply 見出し 1 to the text that you want to appear here. 3 3. Basic operation 3-1. Installation and connection This equipment connect with the interface board of our products. ＜Interface board＞ Part Number Part Description 12-05136 Main board 12-05310 Driver board ＜Connection＞ Connector type: EH connector B8B-EH (JST) Pin Number Signal Description 1 IRQ 2 SS 3 DIN 4 DOUT 5 CLK 6 EN 7 VCC（3.3V） 8 GND Burette Unit EBU Interface cable Interface board RFID board 4. Specification 4-1. Specification Specification Contents Type Burette Unit Model EBU RF Specifications Transmit frequency 13.56MHz Modulation scheme ASK modulation Transmission output 100mW Supported IC Taｇ ISO/IEC 15693、 ISO/IEC18000-3（Mode1） Ambient conditions Temperature : 5 to 35°C Humidity : 85%RH or below (no condensation) Power supply DC3.3V 150mA（MAX） Dimensions 120 (W) × 72 (D) × 188 (H) mm We…

Text truncated - open the document above for the full version.

                    

              








      !"#   $    %&'    %()*+%        , "  "  "           -  "    .       /0 1  2%%
 )  3   /  /  456   "        & 576      "      &       "                 /4 %   2%%(8479:# '   
2(80;

Page 1 of 1 Rev.00 Test Report No. R121125-1 Appendix 2 External Photos ERF130328 Cosmos Corporation QAF1466 Issued: 13//03/01 Revised: 14/02/12

Operational Description of RFID part of model Burette Unit EBU The RFID tag, which is companion to RFID reader, requires no internal power supply. Its contactless interface generates the power supply and the system clock via the resonant circuitry by inductive coupling to the reader. The interface also demodulates data, which is transmitted from the reader to the label IC, and modulates the electromagnetic field for data transmission from the label IC to the reader. Data is stored in a non-volatile memory (EEPROM). The part of RFID reader receives serial and control data from Printer part. Then CPU processes modulation signal based on13.56MHz oscillated. The modulated signal is amplified, demodulated and matched into appropriate impedence. Finally the signal is matched to Antenna factor and then it is radiated to RFID tag.

RFID Board Antenna Specification Overseas Division: Yamawaki Bldg 9F 4-8-21 Kudan Minami, Chiyoda-ku, Tokyo 102-0074 JAPAN FAX: +81-3-3237-0537, Phone: +81-3-3239-7333 E-mail: [email protected] URL:http://www.kyoto-kem.com Factory: 56-2 Ninodan-cho,Shinden Kisshoin,Minami-ku,KYOTO 601-8317,JAPAN FAX: +81-75-691-9961, Phone: +81-75-691-4122 Table of Contents Page 1. Antenna Specification 1 1-1. Antenna Specification 1 1-2. Shape of the antenna 1 1-3. RFID Board Specification 2 1. Antenna Specification 1.1. Antenna Specification Specification Contents Model RFID Board Shape Print pattern antenna Frequency 13.56MHz Characteristic impedance 50O Maximum gain -59.41 dBi Ambient conditions Temperature :5 to 35 Humidity :85%RH or below (no condensation) Antenna Dimensions 27.6 (W) × 24 (D) × 0.018 (H) mm Weight Approx. 6g 1.2. Shape of the antenna 1.3. RFID Board Specification Appearance 1) RFID Board 2) Interface cable connector Circuit Board Specification Item Contents Name RFIDBoard Part Number 20-09376 Dimensions 40×40mm Materials FR-4 Thickness of the circuit board t = 1.6mm Number of layers 4-layer Thickness of the copper foil 18μm Connector type: EH connector B8B-EH (JST) Pin Number Signal Description 1 IRQ 2 SS 3 DIN 4 DOUT 5 CLK 6 EN 7 VCC3.3V 8 GND 21

Page 1 of 1 Rev.00 Test Report No. R121125-1 Appendix 1 EUT Angle Front View Rear View ERF130328 Cosmos Corporation QAF1466 Issued: 13//03/01 Revised: 14/02/12 Left Side Right Side Left Side Right Side

Page 1 of 1 Rev.00 Test Report No. R121125-1 Appendix 1 EUT Angle Front View Rear View ERF130328 Cosmos Corporation QAF1466 Issued: 13//03/01 Revised: 14/02/12 Left Side Right Side Left Side Right Side

Page 1 of 1 Rev.00 Test Report No. R121125-1 Appendix 2 External Photos ERF130328 Cosmos Corporation QAF1466 Issued: 13//03/01 Revised: 14/02/12

Page 1 of 4 Rev.00 Test Report No. R121125-1 Appendix 3 Setup Photos AC Power Line Conducted Emission ERF130328 Cosmos Corporation QAF1466 Issued: 13//03/01 Revised: 14/02/12 Page 2 of 4 Rev.00 Appendix 3 (Continued) Radiated Emission (Below 30 MHz) ERF130328 Cosmos Corporation QAF1466 Issued: 13//03/01 Revised: 14/02/12 Page 3 of 4 Rev.00 Appendix 3 (Continued) Radiated Emission (Above 30 MHz) ERF130328 Cosmos Corporation QAF1466 Issued: 13//03/01 Revised: 14/02/12 Page 4 of 4 Rev.00 Appendix 3 (Continued) Frequency Tolerance ERF130328 Cosmos Corporation QAF1466 Issued: 13//03/01 Revised: 14/02/12

               !"# $ #  % $ #   &' $ # ( (  !)* $  (   + ,!*    -# * . #/ *   ! 0+" # "1 )# # 2 +! 3     " .  &' % )"*    "  (+ "  "  (.%4!"# !&  () 5  (  (  "  ((+ "!$ ( (670!2! !)"" &  () 5  (  (  " . ((+ "!$ . ( 0#2!8/!4! ,6 ( ) 5 6 (  6 (   " 6 ( (+ "!$  ((020/20#20!2-!)  , -"! &  (() 5  ((  ((  "  (((+ "!$  (02-9"#* # () 5  (  (  "  ((+ "!$ (     + "  "  %!:              …

Text truncated - open the document above for the full version.

Page 1 of 4 Rev.00 Test Report No. R121125-1 Appendix 3 Setup Photos AC Power Line Conducted Emission ERF130328 Cosmos Corporation QAF1466 Issued: 13//03/01 Revised: 14/02/12 Page 2 of 4 Rev.00 Appendix 3 (Continued) Radiated Emission (Below 30 MHz) ERF130328 Cosmos Corporation QAF1466 Issued: 13//03/01 Revised: 14/02/12 Page 3 of 4 Rev.00 Appendix 3 (Continued) Radiated Emission (Above 30 MHz) ERF130328 Cosmos Corporation QAF1466 Issued: 13//03/01 Revised: 14/02/12 Page 4 of 4 Rev.00 Appendix 3 (Continued) Frequency Tolerance ERF130328 Cosmos Corporation QAF1466 Issued: 13//03/01 Revised: 14/02/12