2AC6N-B370SMART CARD READER

SCC-RF-MI-B370 Reader User Manual Make sure USB port (1) connects to PC ,another port (2) connects to reader port (3),then you will hear buzzer sounds from reader ,check the red (4)and White (5) power light’s status , they will turn red and white . 1 2 3 4 5 6 First ,Driver installation process 1.1,At this point you will see in the lower right corner of the Windows Found New Hardware prompt, Eject Hardware Update Wizard 1.2,Select "setup from listed or specified location" , click "Next" then 1.3,Select "Search for the best driver in these locations" and then "Include this location in the search" tick, click Browse, select the folder to ccid driver, click Next 1.4,Click Browse, select the ccid driver folder, click OK, immediately after the completion of. 1.5,After installing the device driver in the Device Manager can be seen inside the device is smart USB Smart Card Reader Card reader under. Second, Device Test 2.1,After the device driver is installed, open the demo folder, open demo.exe, under normal circumstances it should appear directly like below shown. 2,Click “select reader”，the reader will be able to detect the card reader in a column reader 3,Follow the instructions on the card reader logo, placed on reading and writing area (6), the white status indicator (5) bright green, the reader buzzer sounds, will appear in the ATR column card information, as shown below. 4,Click on a column "reader", reader information below, then "OK". 5,In the "Connection Protocol" select "T1", then click on "2, connect", properly connected, the following "3, transmit" will become available from gray. 6, the message to enter the card's box "ffca000000", then "3, transmit", will appear the following answer from reader M1 UID numbers (before 8 digits), and finally the bit for 900 7,Finally, the card reader scored from the reader buzzer beep, white status indicator (5) lights red. FCC STATEMENT 1.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1).This device may not cause harmful interference. (2).This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (current) 4.0 5.0 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0 SHENZHEN LANGZHUO TECHNOLOGY CO., LTD. 2014-09-19 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, SHENZHEN LANGZHUO TECHNOLOGY CO., LTD. hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): Product Description: SMART CARD READER Model name: SCC-RF-MI-B370 FCC ID: 2AC6N-B370 Sincerely, Client’s signature ：zhiqiang zhou Client’s name / title： Manager Contact information / address ：86-755-25615204 （ROOM 407, CHUNTIANGE, JIAHUXINDU,TIANBEI 4TH ROAD, LUOHU DISTRICT,SHENZHEN, GUANGDONG,CHINA）

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 SHENZHEN LANGZHUO TECHNOLOGY CO., LTD. 2014-09-18 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2AC6N-B370 We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Operational Description - Schematic The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature ：zhiqiang zhou Client’s name / title： Manager Contact information / address ：86-755-25615204 （ROOM 407, CHUNTIANGE, JIAHUXINDU,TIANBEI 4TH ROAD, LUOHU DISTRICT,SHENZHEN, GUANGDONG,CHINA）

SHENZHEN LANGZHUO TECHNOLOGY CO., LTD. To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD FCC ID: 2AC6N-B370 To Whom It May Concern: This letter is to ascertain that SHENZHEN LANGZHUO TECHNOLOGY CO., LTD. （Product： SMART CARD READER Model name: SCC-RF-MI-B370 has been the units used for conducting FCC compliance testing, the DoC part will be tested by FCC recognized test lab. If you have any question or concerns, pls. contact us. Sincerely, Client’s signature ：zhiqiang zhou Client’s name / title： Manager Contact information / address ：86-755-25615204 （ROOM 407, CHUNTIANGE, JIAHUXINDU,TIANBEI 4TH ROAD, LUOHU DISTRICT,SHENZHEN, GUANGDONG,CHINA）

Antenna

Report No.: ATE20141750 Page 1 of 26 FCC ID: 2AC6N-B370 ACCURATE TECHNOLOGY CO., LTD APPLICATION CERTIFICATION FCC Part 15C On Behalf of SHENZHEN LANGZHUO TECHNOLOGY CO., LTD. SMART CARD READER Model No.: SCC-RF-MI-B370 FCC ID: 2AC6N-B370 Prepared for : SHENZHEN LANGZHUO TECHNOLOGY CO., LTD. Address : ROOM 407, CHUNTIANGE, JIAHUXINDU,TIANBEI 4TH ROAD, LUOHU DISTRICT,SHENZHEN, GUANGDONG,CHINA Prepared by : ACCURATE TECHNOLOGY CO., LTD Address : F1, Bldg. A, Chan Yuan New Material Port, Keyuan Rd. Science & Industry Park, Nan Shan, Shenzhen, Guangdong P.R. China Tel: (0755) 26503290 Fax: (0755) 26503396 Report Number : ATE20141750 Date of Test : Sep 04-18, 2014 Date of Report : Sep 18, 2014 Report No.: ATE20141750 Page 2 of 26 FCC ID: 2AC6N-B370 ACCURATE TECHNOLOGY CO., LTD TABLE OF CONTENTS Description Page Test Report Certification 1. GENERAL INFORMATION............................................................................................................ 5 1.1. Description of Device (EUT).................................................................................................................5 1.2. Special Accessory and Auxiliary Equipment......................................................................................5 1.3. Description of Test Facility ......................................................................................................................6 1.4. Measurement Uncertainty.........................................................................................................................6 2. MEASURING DEVICE AND TEST EQUIPMENT ..................................................................... 7 3. OPERATION OF EUT DURING TESTING ................................................................................. 8 3.1. Operating Mode ........................................................................................................................................8 3.2. Configuration and peripherals ..................................................................................................................8 4. TEST PROCEDURES AND RESULTS ......................................................................................... 9 5. 20DB BANDWIDTH MEASUREMENT ...................................................................................... 10 5.1. Block Diagram of Test Setup..................................................................................................................10 5.2. The Requirement For Section 15.215(c).................................................................................................10 5.3. Operating Condition of EUT ..................................................................................................................10 5.4. Test Procedure ........................................................................................................................................10 5.5. Test Result ..............................................................................................................................................11 6. FIELD STRENGTH OF FUNDAMENTAL EMISSION ........................................................... 12 6.1. Block Diagram of Test Setup..................................................................................................................12 6.2. The Requirement For Section 15.225 .....................................................................................................12 6.3. EUT Configuration on Measurement .....................................................................................................12 6.4. Operating Condition of EUT ..................................................................................................................13 6.5. Test Procedure ........................................................................................................................................13 6.6. Test Result ..............................................................................................................................................13 7. RADIATED SPURIOUS EMISSION TEST ................................................................................ 15 7.1. Block Diagram of Test Setup..................................................................................................................15 7.2. The Limit For Section 15.249.................................................................................................................16 7.3. Configuration of EUT on Measurement .................................................................................................16 7.4. Test Procedure ........................................................................................................................................16 7.5. The Field Strength of Radiation Emission Measurement Results ..........................................................17 8. FREQUENCY STABILITY ........................................................................................................... 20 8.1. Block Diagram of Test Setup..................................................................................................................20 8.2. The Limit For Section 15.225(e) ............................................................................................................20 8.3. Operating Condition of EUT ..................................................................................................................20 8.4. Test Procedure ........................................................................................................................................20 8.5. Test Result ..............................................................................................................................................21 9. AC POWER LINE CONDUCTED EMISSION FOR FCC PART 15 SECTION 15.207(A) .. 22 9.1. Block Diagram of Test Setup...............................…

Text truncated - open the document above for the full version.