2AC9EOTH-S0361BLUETOOTH BRACELET

Federal Communications Commission (FCC) Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  ƽReorient or relocate the receiving antenna. ƽIncrease the separation between the equipment and receiver. ƽConnect the equipment into an outlet on a circuit different from that to which the receiver is connected. ƽConsult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications made to this device not expressly approved by Jaskey Limited may void the FCC authorization to operate this device. Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

JASKEY LIMITED 1017-1019, HUATONG BUILDING, THE EAST OF SUNGANG, LUOHU DISTRICT, SHENZHEN, CHINA TEL: (+86) 0755-86174580 FAX: (+86) 0755-86174027 DATE 10-15-2014 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AC9EOTH-S0361 Product Name: BLUETOOTH BRACELET Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...) • Schematics • Block diagram • Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 10-15-2014 By: Wonderful Wang Signature Printed Title: Manager On behalf of : JASKEY LIMITED Telephone: (+86) 0755-86174580

JASKEY LIMITED 1017-1019, HUATONG BUILDING, THE EAST OF SUNGANG, LUOHU DISTRICT, SHENZHEN, CHINA TEL: (+86) 0755-86174580 FAX: (+86) 0755-86174027 Series Models Description FCC ID: 2AC9EOTH-S0361 Date: Sept. 28, 2014 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern: To whom concern: The device (Product Name: BLUETOOTH BRACELET ) Models Name: OTH-S0361, PBTW155-ASST1 have same electrical, PCB and BOM, only the model’s name and color are different for marketing requirements. Sincerely, Wonderful Wang /Manager

JASKEY LIMITED 1017-1019, HUATONG BUILDING, THE EAST OF SUNGANG, LUOHU DISTRICT, SHENZHEN, CHINA TEL: (+86) 0755-86174580 FAX: (+86) 0755-86174027 USB Port Statement FCC ID: 2AC9EOTH-S0361 Date: Sept. 28, 2014 To whom it may concern: We, the undersigned, state that the device's (Model: OTH-S0361, PBTW155-ASST1) USB port only used for charge, no any data transfer to PC. Sincerely, Wonderful Wang/Manager

FCC ID Label Information 1. Label location: 2. FCC ID Label: BLUETOOTH BRACELET FCC ID: 2AC9EOTH-S0361

RF Exposure evaluation According to KDB 447498 D01 General RF Exposure Guidance v05 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison eirp = pt x gt = (EXd) 2 /30 where: pt = transmitter output power in watts, gt = numeric gain of the transmitting antenna (unitless), E = electric field strength in V/m, --- 10 ((dBuV/m)/20) /10 6 d = measurement distance in meters (m)---3m So pt = (EXd) 2 /30 x gt Field strength = 72.13 dBuV/m @3m Ant gain 0dBi ;so Ant numeric gain=1 So pt={ [10 (72.13 /20) /10 6 x3] 2 /30x1 }x1000 mW = 0.006mW So ( 0.006mW/5mm)x √2.440GHz = 0.002 <3 Then SAR evaluation is not required

Shenzhen CTL Testing Technology Co., Ltd. Tel: +86-755-89486194 Fax: +86-755-26636041 FCC PART 15 SUBPART C TEST REPORT FCC Part 15.249 Report Reference No......................: CTL1409192345-WF Compiled by ( position+printed name+signature)..: File administrators Jacky Chen Name of the organization performing the tests ( position+printed name+signature)..: Test Engineer Tracy Qi Approved by ( position+printed name+signature)..: Manager Tracy Qi Date of issue.....................................: Oct. 15, 2014 Test Firm..........................................: Shenzhen CTL Testing Technology Co., Ltd. Address.............................................: Floor 1-A, Baisha Technology Park, No. 3011, Shahexi Road, Nanshan, Shenzhen 518055 China. Applicant’s name............................: JASKEY LIMITED Address.............................................: 1017-1019, HUATONG BUILDING, THE EAST OF SUNGANG, LUOHU DISTRICT, SHENZHEN, CHINA Test specification: Standard ...........................................: FCC Part 15.249: Operation within the bands 920-928 MHz, 2400- 2483.5 MHz, 5725-5850 MHz and 24.0 - 24.25 GHz. TRF Originator ..................................: Shenzhen CTL Testing Technology Co., Ltd. Master TRF.......................................: Dated 2011-01 Shenzhen CTL Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen CTL Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTL Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .................... : BLUETOOTH BRACELET Trade Mark .......................................: N/A Models/Type reference.....................: OTH-S0361, PBTW155-ASST1 Modulation .......................................: GFSK Work Frequency...........................: 2402 MHz~2480 MHz Antenna Type..............................: internal FCC ID .............................................: 2AC9EOTH-S0361 Result................................................: Positive V1.0 Page 2 of 34 Report No.: CTL1409192345-WF T E S T R E P O R T Test Report No. :CTL1409192345-WF Oct. 15, 2014 ______________________________________________________________________________________________ Date of issue Equipment under Test : BLUETOOTH BRACELET Model /Type : OTH-S0361 Listed Modes PBTW155-ASST1 Difference Description Only the color and model's name is different Applicant : JASKEY LIMITED Address : 1017-1019, HUATONG BUILDING, THE EAST OF SUNGANG, LUOHU DISTRICT, SHENZHEN, CHINA Manufacturer Dampsonic Electronic (Shen zhen) Co.,Ltd Address BUILDING C, YUSHAN INDUSTRY ZONE, SHIYAN TOWN, BAO AN DISTRICT,SHENZHEN,CHINA  Test Result according to the standards on page 4: Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. V1.0 Page 3 of 34 Report No.: CTL1409192345-WF Contents 1 . TEST STANDARDS.......................................................................4 2 . SUMMARY...................................................................................5 2.1. General Remarks .........................................................................................................................................5 2.2. Equipment Under Test ................................................................................................................................5 2.3. Short description of the Equipment under Test (EUT) ............................................................................5 2.4. EUT operation mode ...................................................................................................................................6 2.5. EUT configuration .......................................................................................................................................6 2.6. Related Submittal(s) / Grant (s)..................................................................................................................6 2.7. Modifications ...............................................................................................................................................6 3 . TEST ENVIRONMENT ....................................................................7 3.1. Address of the test laboratory ...................................................................................................................7 3.2. Test Facility ..................................................................................................................................................7 3.3. Environmental conditions ..........................................................................................................................7 3.4. Configuration of Tested System ................................................................................................................7 3.5. Statement of the measurement uncertainty .............................................................................................7 3.6. Equipments Used during the Test .............................................................................................................9 4 . TEST CONDITIONS AND RESULTS ..................................................9 4.1. Conducted Emissions Test ......................................................................................................................10 4.2. Radiated Emission Test ............................................................................................................................13 4.3. Band Edge Measurement.......................................................................................................…

Text truncated - open the document above for the full version.