2ACCJH175GSM/UMTS/LTE Mobile phone

Quick Start Guide 1 At a glance Let’s get started. We’ll guide you through startup and tell you where to find more information about your phone and its great features. Power key/ Google Assistant Volume keys Microphone USB Type-C Headset connector Front camera Microphone 2 Set up your SIM card The SIM (Subscriber Identity Module) card identifies your device to the wireless network. You can't make or receive phone calls without a properly installed SIM card unless it's an emergency call (911). You don't need to power off your device before inserting or removing the SIM card. Note: Your device only supports Nano SIM cards. To avoid damage to your device, do not attempt to insert any other SIM types. With the phone face down, remove the back cover by gently pulling up on the indentation on the bottom left of the cover. Place or remove the Nano SIM card and the microSD TM card in the correct slot as shown. Note: MicroSD TM cards are sold separately. 3 Battery Insert the battery by connecting the gold contacts in the device battery cavity. The battery will only fit one way. To optimize battery performance, be sure to fully charge your device before using it for the first time. Charging the device 1. Insert the USB Type-C cable into the charge port as shown. 2. Connect charger to power outlet. Note: Please use the charger and USB Type-C cable that’s included with your device. Using the wrong cable and charger may damage the charging port or reduce battery performance. 4 Optimize battery life To optimize battery life, adjust your screen brightness and display timeout. 1. Adjusting brightness level: Lowering your screen brightness level can optimize your battery level. To adjust the brightness level, swipe up from the Home screen, touch Settings > Display > Brightness level. To lower the brightness level, move the wheel to the left. 2. Power saving mode: Power saving mode minimizes battery usage to extend battery life. To explore power management options, swipe up from the Home screen, touch Settings > Smart Manager > Battery > Super saving mode. Then touch ENABLE to activate power saving mode. 3. Adjust screen timeout: Sleep mode is a low power mode function and it significantly saves your battery power. Lower the amount of time your device stays on after you stop using it to optimize your battery level. To do so, swipe up from the Home screen, touch Settings > Display > Sleep and select screen timeout duration. 5 Security & convenience To protect your phone and privacy, you can activate the following security options: Screen lock: Swipe up from the Home screen, touch Settings > Security & biometrics > Screen lock. Face unlock: Swipe up from the Home screen, touch Settings > Security & biometrics > Face unlock and follow the instructions to set up the face unlock feature. 6 Useful apps When you’re up and running, try these apps to see what you can do with your new phone. Find it: Swipe up from the Home screen to see all your apps. Camera Your mobile phone is equipped with a camera and a camcorder for taking photos and shooting videos. Chrome Using the Chrome browser, you can enjoy surfing the Web. Gmail With Gmail, you can send and receive emails, manage emails by labels, archive them, etc. Messaging You can create, edit, and receive SMS and MMS with this phone. Play Store In Play Store, search for the app you need, download it, and then follow the installation guide to install the app. Settings To access this function, swipe up from the Home screen and then touch Settings. Note: Software updates happen frequently, so your phone may not have all listed apps or features. 7 Approved firmware versions This device will only operate with firmware versions that have been approved for use by your wireless carrier and the device manufacturer. If unauthorized firmware is placed on the device it will not function. Information about safeguarding handsets We encourage customers to take appropriate measures to secure their devices and invite them to take advantage of the features available on this device to help secure it from theft and/ or other unauthorized access and use. This device has a locking function (e.g., Security PINs) that can serve as a first line of defense against unauthorized use or access to stored information. Preloaded security applications that allow customers to track or locate misplaced devices can be found on several devices. Lost or stolen devices should be immediately reported to your wireless carrier so that proper measures can be taken to protect accounts. For additional information, visit your wireless carrier’s Privacy Policy. 8 Emergency call If your phone has network coverage, dial the emergency number and touch to make an emergency call. This works even without a SIM card and without typing the PIN code. Although all phones are equipped with 9-1-1 emergency calling, this phone may or may not permit its location to be approximated during a 9-1-1 call. Be prepared to report your location when dialing 911*. * Availability of this feature depends on upgrades to the (a) wireless network and (b) 9-1-1 calling system that are required to be installed by the local 9-1-1 response agency or public safety answering point (PSAP); these upgrades may not be available everywhere within your wireless service provider’s coverage area or roaming area. This approximation of the phone’s location and the transmittal of location information are subject to emergency situations, transmission limits, network problems/ limitations, interconnecting carrier problems, your phone, buildings/tunnels, signal strength and atmospheric/topographical conditions, and may be curtailed, interrupted, dropped, or refused. The phone’s approximate location may be transmitted to the local 9-1-1 response agency or PSAP while the call is in progress; this approximation is intended solely to aid the PSAP in dispatching emergency assistance or to limit the search area for emergency services personnel. You should not rely …

Text truncated - open the document above for the full version.

TO: Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046, USA ATTENTION: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company Name: TCT Mobile (US) Inc. Contact Name: Yao Dai Street Address: 189 Technology Drive City/Province/Zip: Irvine, CA 92618 Telephone No: 1-855-368-0829 Email: [email protected] FRN #: 0033429465 This letter is to confirm that we (“the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U.S. Agent Signature: Date: Signed by (Printed Name/Title): Yao Dai / Technical Acceptance Manager The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: TCL Communication Ltd. Grantee Code: 2ACCJ Contact Name: Annie Jiang Street Address: 5/F, Building 22E, 22 Science Park East Avenue, Hong Kong Science Park, Shatin, NT, Hong Kong City/Province/Zip: Hongkong Telephone No: +86 755 36611621 Email: [email protected] Applicant Signature: Date: 2023-6-26 Signed by (Printed Name/Title): Annie Jiang / Product Certification Manager DocuSign Envelope ID: E928EFD3-F956-4FF1-9FB9-50DFDDAD0B2F June 27, 2023

TCL Communication Ltd. Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Date: July 3, 2023 Subject: Certifications concerning “covered” equipment pursuant to Part 2.911(d)(5)(i) and (ii) To whom it may concern, TCL Communication Ltd. certifies that the equipment FCC ID: 2ACCJH170 for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. TCL Communication Ltd. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, ________________________ Name: Annie Jiang E-mail: [email protected]

TCL Communication Ltd. 5/F, Building 22E, 22 Science Park East Avenue, Hong Kong Science Park, Shatin, NT, Hong Kong Tel: 0086-755-36611722 http://tclcom.tcl.com Date 2022-09-30 To: Federal Communications Commission, Authorization & Evaluation Division, 7345 Oakland Mills Road Columbia, MD 21046 And American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: CTTL-Telecommunication Technology Labs, Academy of Telecommunication Research, MIIT is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, which includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, U.S.C. 862. Further, no party, as defined in 47 CFR1.2002 (b) to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you. Regards, Annie Jiang Product Certification Manager TCL Communication Ltd. Date 2023-07-03

TCL Communication Ltd. 5/F, Building 22E, 22 Science Park East Avenue, Hong Kong Science Park, Shatin, NT, Hong Kong Tel: 0086-755-36611722 http://tclcom.tcl.com 2023-07-03 Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: Permanent Confidentiality request for FCC ID: 2ACCJH175 To Whom It May Concern, Pursuant to sections 0.457 and 0.459 of CFR 47, the applicant requests permanent confidential treatment of the following information accompanying this application: - Block Diagram - Schematics - Operational Description - BOM list/Tune-Up-Procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. Yours Sincerely, Annie Jiang Product Certification Manager TCL Communication Ltd.

TCL Communication Ltd. 5/F, Building 22E, 22 Science Park East Avenue, Hong Kong Science Park, Shatin, NT, Hong Kong Tel: 0086-755-36611722 http://tclcom.tcl.com 2023-07-03 Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: SHORT-TERM Confidentiality request for FCC ID: 2ACCJH175 To Whom It May Concern, Pursuant to sections 0.457 and 0.459 of CFR 47 and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 180 days: - External Photos - Internal Photos - Test Setup Photos - User manual The applicant also acknowledges that they will also provide appropriate notice to ACB should either of the following occur: a) if the applicant requires additional 45 days extension periods they will notify ACB with a new request letter at least 7 days prior to the short-term confidentiality expiration date – [Note: up to a maximum of 3 extensions only are allowed], or b) Immediately notify ACB in the event the information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Yours Sincerely, Annie Jiang Product Certification Manager TCL Communication Ltd.

EUT photograph Battery TLi028C7 Battery TLi028C7 Battery TLi028CA Battery TLi028CA UC13US -Label UC13US UC13US -N-Label UC13US –N CDA0000123C1

EUT Interior photograph

No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. ANNEX A Graph Results No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. ANNEX B SYSTEM VALIDATION RESULTS 750 MHz Date: 6/20/2023 Electronics: DAE4 Sn1556 Medium: H700-6000M Medium parameters used: f = 750 MHz; σ = 0.8308 S/m; εr = 44.23; ρ = 1000 kg/m3 Ambient Temperature:23.3°C Liquid Temperature: 22.5°C Communication System: CW (0) Frequency: 750 MHz Duty Cycle: 1:1 Probe: EX3DV4 - SN3617 ConvF(10.10, 10.10, 10.10) Area Scan (131x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 2.77 W/kg Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 53.72 V/m; Power Drift = -0.08 dB Peak SAR (extrapolated) = 3.25 W/kg SAR(1 g) = 2.11 W/kg; SAR(10 g) = 1.38 W/kg Maximum value of SAR (measured) = 2.83 W/kg 0 dB = 2.83 W/kg = 4.52 dBW/kg No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. 835 MHz Date: 6/21/2023 Electronics: DAE4 Sn1556 Medium: H700-6000M Medium parameters used: f = 835 MHz; σ = 0.8757 S/m; εr = 44.06; ρ = 1000 kg/m3 Ambient Temperature:23.3°C Liquid Temperature: 22.5°C Communication System: CW (0) Frequency: 835 MHz Duty Cycle: 1:1 Probe: EX3DV4 - SN3617 ConvF(9.68, 9.68, 9.68) Area Scan (131x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 3.12 W/kg Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 59.25 V/m; Power Drift = -0.09 dB Peak SAR (extrapolated) = 3.61 W/kg SAR(1 g) = 2.38 W/kg; SAR(10 g) = 1.54 W/kg Maximum value of SAR (measured) = 3.22 W/kg 0 dB = 3.22 W/kg = 5.08 dBW/kg No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. 1750 MHz Date: 6/22/2023 Electronics: DAE4 Sn1556 Medium: H700-6000M Medium parameters used: f = 1750 MHz; σ = 1.384 S/m; εr = 41.46; ρ = 1000 kg/m3 Ambient Temperature:23.3°C Liquid Temperature: 22.5°C Communication System: CW (0) Frequency: 1750 MHz Duty Cycle: 1:1 Probe: EX3DV4 - SN3617 ConvF(8.40, 8.40, 8.40) Area Scan (61x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 13.65 W/kg Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 97.51 V/m; Power Drift = 0.07 dB Peak SAR (extrapolated) = 16.75 W/kg SAR(1 g) = 8.85 W/kg; SAR(10 g) = 4.68 W/kg Maximum value of SAR (measured) = 13.87 W/kg 0 dB = 13.87 W/kg = 11.41 dBW/kg No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. 1900 MHz Date: 6/28/2023 Electronics: DAE4 Sn1556 Medium: H700-6000M Medium parameters used: f = 1900 MHz; σ = 1.475 S/m; εr = 40.96; ρ = 1000 kg/m3 Ambient Temperature:23.3°C Liquid Temperature: 22.5°C Communication System: CW (0) Frequency: 1900 MHz Duty Cycle: 1:1 Probe: EX3DV4 - SN3617 ConvF(8.14, 8.14, 8.14) Area Scan (61x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 15.77 W/kg Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 100.8 V/m; Power Drift = 0.08 dB Peak SAR (extrapolated) = 19.1 W/kg SAR(1 g) = 10.06 W/kg; SAR(10 g) = 5.09 W/kg Maximum value of SAR (measured) = 15.1 W/kg 0 dB = 15.1 W/kg = 11.79 dBW/kg No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. 2450 MHz Date: 6/26/2023 Electronics: DAE4 Sn1556 Medium: H700-6000M Medium parameters used: f = 2450 MHz; σ = 1.893 S/m; εr = 40.15; ρ = 1000 kg/m3 Ambient Temperature:23.3°C Liquid Temperature: 22.5°C Communication System: CW (0) Frequency: 2450 MHz Duty Cycle: 1:1 Probe: EX3DV4 - SN3617 ConvF(7.68, 7.68, 7.68) Area Scan (61x61x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Maximum value of SAR (interpolated) = 21.1 W/kg Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 98.58 V/m; Power Drift = 0.09 dB Peak SAR (extrapolated) = 27.4 W/kg SAR(1 g) = 12.8 W/kg; SAR(10 g) = 6.02 W/kg Maximum value of SAR (measured) = 21.2 W/kg 0 dB = 21.2 W/kg = 13.26 dBW/kg No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. 2600 MHz…

Text truncated - open the document above for the full version.

No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. ➢ Jerk-free straight movements (brushless synchron motors; no stepper motors) ➢ Low ELF interference (motor control fields shielded via the closed metallic construction shields) Picture C.5 DASY 5 C.4.3 Measurement Server The Measurement server is based on a PC/104 CPU broad with CPU (DASY5: 400 MHz, Intel Celeron), chipdisk (DASY5: 128MB), RAM DASY5: 128MB). The necessary circuits for communication with the DAE electronic box, as well as the 16 bit AD converter system for optical detection and digital I/O interface are contained on the DASY I/O broad, which is directly connected to the PC/104 bus of the CPU broad. The measurement server performs all re al-time d ata evaluation of field measurements and surface detection, controls robot movements and handles safety operation. The PC operating system cannot interfere with these time critical processes. All connections are supervised by a watchdog, and disconnection of any of the cables to the measurement server will automatically disarm the robot and disable all program-controlled robot movements. Furthermore, the measurement server is equipped with an expansion port which is reserved for future applications. Please note that this expansion port does not have a standardized pinout, and therefore only devices provided by SPEAG can be connected. Devices from any other supplier could seriously damage the measurement server. Picture C.6 Server for DASY 5 C.4.4 Device Holder for Phantom The SAR in the phantom is approximately inversely proportional to the square of the distance between the source and the liquid surface. For a source at 5mm distance, a positioning uncertainty of ±0.5mm would produce a SAR uncertainty of ±20%. Accurate device positioning is therefore crucial for accurate and repeatable measurements. The positions in which the devices must be measured are defined by the standards. The DASY device holder is designed to cope with the different positions given in the standard. It has No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. two scales for device rotation (with respect to the body axis) and device inclination (with respect to the line between the ear reference points). The rotation centers for both scales are the ear reference point (ERP). Thus the device needs no repositioning when changing the angles. The DASY device holder is constructed of low-loss POM material having the following dielectric parameters: relative permittivity  =3 and loss tangent  =0.02. The amount of dielectric material has been reduced in the closest vicinity of the device, since measurements have suggested that the influence of the clamp on the test results could thus be lowered. <Laptop Extension Kit> The extension is lightweight and made of POM, acrylic glass and foam. It fits easily on the upper part of the Mounting Device in place of the phone positioner. The extension is fully compatible with the Twin-SAM and ELI phantoms. Picture C7-1: Device Holder Picture C.7-2: Laptop Extension Kit C.4.5 Phantom The SAM Twin Phantom V4.0 is constructed of a fiberglass shell integrated in a table. The shape of the shell is based on data from an anatomical study designed to Represent the 90 th percentile of the population. The phantom enables the dissymmetric evaluation of SAR for both left and right handed handset usage, as well as body-worn usage using the flat phantom region. Reference markings on the Phantom allow the complete setup of all predefined phantom positions and measurement grids by manually teaching three points in the robot. The shell phantom has a 2mm shell thickness (except the ear region where shell thickness increases to 6 mm). Shell Thickness: 2±0. 2 mm Filling Volume: Approx. 25 liters Dimensions: 810 x l000 x 500 mm (H x L x W) Available: Special No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. Picture C.8: SAM Twin Phantom No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. ANNEX D Position of the wireless device in relation to the phantom D.1 General considerations This standard specifies two handset test positions against the head phantom – the “cheek” position and the “tilt” position. t w Width of the handset at the level of the acoustic b w Width of the bottom of the handset A Midpoint of the width t w of the handset at the level of the acoustic output B Midpoint of the width b w of the bottom of the handset Picture D.1-a Typical “fixed” case handset Picture D.1-b Typical “clam-shell” case handset Picture D.2 Cheek position of the wireless device on the left side of SAM No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. Picture D.3 Tilt position of the wireless device on the left side of SAM D.2 Body-worn device A typical example of a body-worn device is a mobile phone, wireless enabled PDA or other battery operated wireless device with the ability to transmit while mounted on a person’s body using a carry accessory approved by the wireless device manufacturer. Picture D.4Test positions for body-worn devices D.3 Desktop device A typical example of a desktop device is a wireless enabled desktop computer placed on a table or desk when used. The DUT shall be positioned at the distance and in the orientation to the phantom that corresponds to the intended use as specified by the manufacturer in the user instructions. For devices that employ an external antenna with variable positions, tests shall be performed for all antenna positions specified. Picture8.5 show positions for desktop device SAR tests. If the intended use is not specified, the device shall be tested directly against the flat phantom. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. Picture D.5 Test positions for desktop devices D.3 DUT Setup Photos Picture D.6 No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. ANNEX E Equivalent Media Recipes The liquid used for the frequency range of 800-3000 MHz consisted of water, sugar, salt, preventol, glycol …

Text truncated - open the document above for the full version.

No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. 1750 MHz Dipole Calibration Certificate No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. 1900 MHz Dipole Calibration Certificate No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. 2450 MHz Dipole Calibration Certificate No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. 2600 MHz Dipole Calibration Certificate No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. ANNEX I Accreditation Certificate

©Copyright. All rights reserved by CTTL. SAR TEST REPORT No. I23Z60906-SEM01 For TCL Communication Ltd. GSM/UMTS/LTE Mobile phone Model Name: T432W With Hardware Version: 03 Software Version: LXS4 FCC ID: 2ACCJH175 Issued Date: 2023-7-6 Note: The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced except in full without the written approval of CTTL. Test Laboratory: CTTL, Telecommunication Technology Labs, CAICT No. 52, Huayuan North Road, Haidian District, Beijing, P. R. China 100191. Tel:+86(0)10-62304633-2512, Fax:+86(0)10-62304633-2504 Email: [email protected], website: www.caict.ac.cn No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. Page 2 of 95 REPORT HISTORY Report Number Revision Issue Date Description I23Z60906-SEM01 Rev.0 2023-7-3 Initial creation of test report I23Z60906-SEM01 Rev.1 2023-7-6 Update the maximum power for BT in section11.4 on page80 No. I23Z60906-SEM01 ©Copyright. All rights reserved by CTTL. Page 3 of 95 TABLE OF CONTENT 1 TEST LABORATORY ............................................................................................................... 5 1.1 TESTING LOCATION ........................................................................................................................................................ 5 1.2 TESTING ENVIRONMENT ................................................................................................................................................ 5 1.3 PROJECT DATA................................................................................................................................................................. 5 1.4 SIGNATURE....................................................................................................................................................................... 5 2 STATEMENT OF COMPLIANCE .............................................................................................. 6 3 CLIENT INFORMATION ........................................................................................................... 8 3.1 APPLICANT INFORMATION ............................................................................................................................................. 8 3.2 MANUFACTURER INFORMATION ................................................................................................................................... 8 4 EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT (AE) ............................... 9 4.1 ABOUT EUT..................................................................................................................................................................... 9 4.2 INTERNAL IDENTIFICATION OF EUT USED DURING THE TEST ................................................................................... 9 4.3 INTERNAL IDENTIFICATION OF AE USED DURING THE TEST...................................................................................... 9 5 TEST METHODOLOGY ......................................................................................................... 10 5.1 APPLICABLE LIMIT REGULATIONS.............................................................................................................................. 10 5.2 APPLICABLE MEASUREMENT STANDARDS................................................................................................................ 10 6 SPECIFIC ABSORPTION RATE (SAR) .................................................................................. 11 6.1 INTRODUCTION.............................................................................................................................................................. 11 6.2 SAR DEFINITION........................................................................................................................................................... 11 7 TISSUE SIMULATING LIQUIDS ............................................................................................. 12 7.1 TARGETS FOR TISSUE SIMULATING LIQUID ................................................................................................................ 12 7.2 DIELECTRIC PERFORMANCE.....................................................................…

Text truncated - open the document above for the full version.