2ACCRMA41Bluetooth module

Bluetooth Transmit Data Module Shanghai Ehong Technologies Inc EH-MA41 User Manual Brand Name:Ehong FCC ID:2ACCRMA41 TX power +5.18dbm, / Bluetooth Transmit Data Module Shanghai Ehong Technologies Inc Description: 3.0 module. It is a highly integrated and sophisticated module which contains all the necessary elements from radio to antenna and a fully implemented protocol stack. It is an ideal solution for integrating Bluetooth® into various products with limited knowledge of Bluetooth® and RF technologies. With AT command stack firmware, designers can easily customize their applications to support different Bluetooth profiles, such as SPP, HID, HFP and etc. And the module can also interface with Apple’s Authentication Coprocessor and build an iAP over Bluetooth application. Typical Bluetooth applications:  Cable replacement  Bar code and RFID scanners  Measurement and monitoring systems  Industrial sensors and controls  Medical devices  Industrial PCs and laptops Features:   -84dBm RX sensitivity  Onboard Meander line PCB antenna support 10 meters  Support sniff and deep sleep mode  Supports master and slave  Supports Bluetooth profiles SPP, iAP, HID  UART and USB and data interfaces  I 2 C Master interface  Support Apple iAP protocol  PCM digital audio interfaces  RoHS compliant Bluetooth V3.0 EH-MA41 is a class 2 Bluetooth® Bluetooth Transmit Data Module Shanghai Ehong Technologies Inc 1. EH-MA41 Product numbering EH-MA41-X-V1.0 A. EH ------------- Company Name(EHong) B. MA41 ------------ Module Name C. X ------------ N (no) D. V ------------ Hardware revision 2. Pinout and Terminal Description 2.1. Pin Configuration Figure 1： Pinout of EH-MA41 Pin Symbol I/O Type Description 1 AIO1 Bi-directional Programmable input/output line 2 GND Ground Ground Bluetooth Transmit Data Module Shanghai Ehong Technologies Inc 3 SPI_MOSI CMOS input, with weak internal pull-down Serial Peripheral Interface data input 4 PIO6 Bi-directional with programmable strength internal pull-up/down Programmable input/output line 5 PIO7 Bi-directional with programmable strength internal pull-up/down Programmable input/output line 6 RESETB CMOS input with weak internal pull-up Reset if low. Input denounced so must be low for >5ms to cause a reset 7 SPI_CLK input with weak internal pull-down Serial Peripheral Interface clock 8 PCM_CLK Bi-directional with weak internal pull-down Synchronous Data Clock 9 PCM_SYNC Bi-directional with weak internal pull-down Synchronous Data Sync 1 0 PCM_IN CMOS Input, with weak internal pull-down Synchronous Data Input 11 PCM_OUT CMOS output, tristate, with weak internal pull-down Synchronous Data Output 12 VDD_3V3 3V3 power input 3V3 power input 13 GND Ground Ground 14 GND Ground Ground 15 PIO11 Bi-directional with programmable strength internal pull-up/down Programmable input/output line 16 PIO10 Bi-directional with programmable strength internal pull-up/down Programmable input/output line 17 PIO9 Bi-directional with programmable strength internal pull-up/down Programmable input/output line 18 PIO8 Bi-directional with programmable strength internal pull-up/down Programmable input/output line 19 GND Ground Ground 20 UART_RXD CMOS input with weak internal pull-down UART data input 21 UART_TXD CMOS output, tristate, with weak internal pull-up UART data output 22 UART_RTS CMOS output, tri-state, with weak internal pull-up UART request to send active low 23 UART_CTS CMOS input with weak internal pull-down UART clear to send active low Bluetooth Transmit Data Module Shanghai Ehong Technologies Inc 24 USB_D+ Bi-directional USB data plus with selectable internal 1.5K pull-up resistor 25 USB_D- Bi-directional USB data minus 26 PIO2 Bi-directional with programmable strength internal pull-up/down Programmable input/output line 27 PIO3 Bi-directional with programmable strength internal pull-up/down Programmable input/output line 28 PIO5 Bi-directional with programmable strength internal pull-up/down Programmable input/output line 29 PIO4 Bi-directional with programmable strength internal pull-up/down Programmable input/output line 30 SPI_CSB CMOS input with weak internal pull-up Chip select for Synchronous Serial Interface active low 31 SPI_MISO CMOS output, tri-state, with weak internal pull-down Serial Peripheral Interface data output 32 AIO0 Bi-directional Programmable input/output line Table 1： PIN Terminal Description Bluetooth Transmit Data Module Shanghai Ehong Technologies Inc 3. Power Supply The module accepts a 3.3V DC power input. Power supply should guarantee good ripple suppression and enough current. . 4. Reset The module may be reset from several sources: RESETB pin, power-on reset, a UART break character or via software configured watchdog timer. The RESETB pin is an active low reset and is internally filtered using the internal low frequency clock oscillator. A reset will be performed between 1.5 and 4.0ms following RESETB being active. It is recommended that RESETB be applied for a period greater than 5ms. Pin Name / Group Pin Status on Reset PIOs Input with weak pull-down AIOs Output, driving low PCM_OUT Tristated with weak pull-down PCM_IN Input with weak pull-down PCM_SYNC Input with weak pull-down PCM_CLK PD UART_TX Output tristated with weak pull-up UART_RX Input with weak pull-down UART_RTS Output tristaed with weak pull-up UART_CTS Input with weak pull-down USB_DP Input with weak pull-down USB_DN Input with weak pull-down SPI_CSB Input with weak pull-up SPI_CLK Input with weak pull-down SPI_MOSI Input with weak pull-down SPI_MISO Tristated with weak pull-down RESETB Input with weak pull-up Table 7: Pin Status on Reset 5. The module integrates a Meander line PCB chip antenna so there’s no need to use antenna on customer’s PCB. Antenna Bluetooth Transmit Data Module Shanghai Ehong Technologies Inc 6. PIO EH-MA41 has a total of 10 digital programmable I/O terminals. They are powered from VDD (3.3V). Their functions depend on firmware running on the device. PIO…

Text truncated - open the document above for the full version.

FCC ID Label Location Model: EH-MA41 Brand Name:Ehong FCC ID: 2ACCRMA41

Report No.: AGC01817140501FE03 Page 1 of 57 FCC Test Report Report No.: AGC01817140501FE03 FCC ID : 2ACCRMA41 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Bluetooth Module BRAND NAME : Ehong MODEL NAME : EH‐MA41 CLIENT : ShangHai Ehong Technology Co.,Ltd. DATE OF ISSUE : May 15, 2014 STANDARD(S) : FCC Part 15 Rules REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context. Report No.: AGC01817140501FE03 Page 2 of 57 Report Revise Record Report Version Revise Time Issued Date Valid VersionNotes V1.0 / May 15, 2014Valid Original Report Report No.: AGC01817140501FE03 Page 3 of 57 TABLE OF CONTENTS 1. VERIFICATION OF CONFORMITY ...................................................................................... 5 2. GENERAL INFORMATION .................................................................................................. 6 2.1. PRODUCT DESCRIPTION ........................................................................................................... 6 2.2. TABLE OF CARRIER FREQUENCYS .......................................................................................... 6 2.3. RECEIVER INPUT BANDWIDTH ................................................................................................. 7 2.4. EXAMPLE OF A HOPPING SEQUENCY IN DATA MODE ........................................................... 7 2.5. EQUALLY AVERAGE USE OF FREQUENCIES AND BEHAVIOUR ............................................ 7 2.6. RELATED SUBMITTAL(S) / GRANT (S) ....................................................................................... 8 2.7. TEST METHODOLOGY................................................................................................................ 8 2.8. SPECIAL ACCESSORIES ............................................................................................................ 8 2.9. EQUIPMENT MODIFICATIONS ................................................................................................... 8 3. MEASUREMENT UNCERTAINTY........................................................................................ 9 4. DESCRIPTION OF TEST MODES ........................................................................................ 9 5. SYSTEM TEST CONFIGURATION .................................................................................... 10 5.1. CONFIGURATION OF EUT SYSTEM ........................................................................................ 10 5.2. EQUIPMENT USED IN EUT SYSTEM ....................................................................................... 10 5.3. SUMMARY OF TEST RESULTS ................................................................................................ 10 6. TEST FACILITY .................................................................................................................. 11 7. PEAK OUTPUT POWER .................................................................................................... 12 7.1. MEASUREMENT PROCEDURE ................................................................................................ 12 7.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ....................................................... 12 7.3. LIMITS AND MEASUREMENT RESULT .................................................................................... 13 8. 20DB BANDWIDTH ............................................................................................................ 19 8.1. MEASUREMENT PROCEDURE ................................................................................................ 19 8.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ....................................................... 19 8.3. LIMITS AND MEASUREMENT RESULTS .................................................................................. 19 9. CONDUCTED SPURIOUS EMISSION ............................................................................... 26 9.1. MEASUREMENT PROCEDURE ................................................................................................ 26 9.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ....................................................... 26 9.3. MEASUREMENT EQUIPMENT USED ....................................................................................... 26 9.4. LIMITS AND MEASUREMENT RESULT .................................................................................... 26 10. RADIATED EMISSION ..................................................................................................... 30 10.1. MEASUREMENT PROCEDURE .............................................................................................. 30 10.2. TEST SETUP ............................................................................................................................ 32 10.3. TEST RESULT .......................................................................................................................... 33 Report No.: AGC01817140501FE03 Page 4 of 57 11. BAND EDGE EMISSION .................................................................................................. 41 11.1. MEASUREMENT PROCEDURE .............................................................................................. 41 11.2. TEST SET-UP ........................................................................................................................... 41 11.3. TEST RESULT .......................................................................................................................... 42 12. NUMBER OF HOPPING FREQUENCY ............................................................................ 46 12.1. MEASUREMENT PROCEDURE .............................................................................................. 46 12.2. TEST SETUP (BLOCK DIAGRAM OF…

Text truncated - open the document above for the full version.

APPENDIX IV PHOTOGRAPHS OF TEST SETUP FCC RADIATED EMISSION TEST SETUP