2ACNR-RECONIIGPS Tracker

Rev. 10/08/14 POWER ON Method 1 - Press the power key at least 3 seconds and release it to power on the Micro Tracker III device. The GPS, GSM and power LED will light for about 3 seconds then go off. The GSM LED will now blink once about every five seconds. Method 2 - Connect the device to the charger. The GPS, Cell and power LED will light for about 3 seconds then go off. The Cell LED will now blink once about every five seconds. POWER OFF Method 1 - Press the power key about 3 seconds. Power LED will light for about 3 seconds then turn off. CHARGING • Connect AC-DC power adapter to device. • Insert the AC-DC power adapter into the power socket • During the charging process, the Power LED light will flash red. When the battery is fully charged, the Power LED light will flash green. You can also charge the battery using the USB cable which connects the Recon II with a computer. • Charging time will take about 5 hours. When not in use, battery should be charged once a month to maintain optimal battery performance. **Note: Please fully charge your Recon II before using the first time. BATTERY LEVEL To check the battery level of your device, visit the coverttrack.com website. COVERAGE AREA The tracking device must be within AT&T coverage to function. Coverage maps are available at: http://www.att.com/maps/wireless-coverage.html LIGHT SEQUENCES GPS LED GPS signal valid Fast flash (blue) GPS turned off/ GPS signal invalid Dark CELL LED Network has been registered Slow flash (yellow) Power off Dark Power LED Power on and normal Dark Fully charged Slow flash (green) In charging Slow flash (red) PANIC ALERT To send a Panic/SOS Alert, hold down the Function button for 3 seconds. PLACEMENT If you are installing the device on the underside of a vehicle, we suggest using a waterproof magnetic mount, available from your dealer. Place the device with the front panel facing up within the magnetic case. Then, place the case under the vehicle within 10” of one side of the vehicle, with the front panel facing down, towards the ground, or out towards the horizon. Do not place the device in the trunk, near the fuel tank, in the engine compartment or by any other heat source. AVAILABLE ACCESSORIES • Weatherproof Magnetic Case • Extended Battery Pack with Magnetic Case RECON II - GPS Tracker USER GUIDE CTrack, LLC. 8361 E. Gelding Drive, Scottsdale, AZ 85260 Tracking: www.coverttrack.com Customer Support 480.657.9545 This device may not interfere with TV reception or Federal Government radar. Rev. 10/08/14 Power Output ...................................................................................................... .01W maximum Operating Frequency ...........................................216.025 – 216.975 MHz - Power 1.2 mW Operating Channels/Modes ........................................................20 channels, 50 kHz spacing Data Rates ............................................................................................................................N/A Tuning Range ........................................................................................216.025 – 216.975 MHz Intended Use ..................................................................................Tracking by Law Enforcement Antenna Connector/Gain Information ........................Internal Antenna, 0 dBi maximum gain CTrack, LLC. 8361 E. Gelding Drive, Scottsdale, AZ 85260 Tracking: www.coverttrack.com Customer Support 480.657.9545 Note: This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and the body of the user or nearby persons. FCC Regulations: 105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an output on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. (15.21) Pursuant to FCC 15.21 of the FCC rules, changes not expressly approved by CTRACK might cause harmful interference and void the FCC authorization to operate this product. (15.19(a)(3)) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation RF Note: This product complies with FCC OET Bulletin 65 radiation exposure limits set forth for an uncontrolled environment. A shielded USB cable must be used with this device. Part 95 Transmitter Technical Specifications

CTrack, LLC 8361 E. Gelding Drive  Scottsdale, AZ 85260  Phone (480) 661-1916  Fax (480) 451-5421  gpsintel.com August 15, 2014 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: I appoint Radiometrics Midwest Corporation to act as CTrack, LLC’s agent in the preparation of application under Part 15, Title 47 of the Code of Federal Regulation of the Federal Communications Commission. I certify that the exhibits properly describe the device being submitted under this application and will implement any changes described in the test report. Radiometrics is authorized to act on its behalf in all matters relating to application for Equipment authorization. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti‐Drug Abuse Act of 1988, 21 U.S.C. 853(a). This authorization is valid until further written notice from the applicant. Jeff Evert President CTrack, LLC

Authorized Agent: Radiometrics Midwest Corporation (815) 293-0772 External EUT Photographs Front of EUT Side View Side View: Port Covers Opened Authorized Agent: Radiometrics Midwest Corporation (815) 293-0772 Side View Rear View

RECON II TRACKING DEVICE FCC LABEL 7/7/14 www.gpsintel.com THIS DEVICE CONTAINS FCC ID: XPYLISAU200 FCC ID: 2ACNR-RECONII MODEL: RECON II 3.000 [76,20] 1.780 [45,21] 0.990 [25,15] MATERIAL IS 0.005 INCH THICK CLEAR POLYESTER WITH 3M467 PERMANENT ADHESIVE BACKING. ALL TEXT IS SECOND SURFACE PRINTED.

Authorized Agent: Radiometrics Midwest Corporation (815) 293-0772 Internal EUT Photographs Photographs of EUT: Cover Removed Photograph of PC Board: Component side, Shield removed Authorized Agent: Radiometrics Midwest Corporation (815) 293-0772 Photograph of PC Board: Foil Side, Shield removed

Tune Up Information for FCC ID 2ACNR‐RECONII 1. There are no tune up adjustments associated with the power range nor at a specific operating power level. The power is set by the design in which the entire transmitter is contained in a single integrated circuit, U20. Since the DUT uses an internal antenna, and is not fitted with an antenna connector, power measurements are to be made via radiated methods. 2. Using a near‐field probe, measure the DUT Y2 crystal frequency. 3. It shall be in the range of 39.998880 to 40.001200 MHz 4. If needed, adjust capacitors C83 and C84 in the range of 10‐ 15 pF to achieve the specified frequency. RECONII – tuneop_2.doc 24 OCT 2014

Authorized Agent: Radiometrics Midwest Corporation (815) 293-0772 MPE Calculations This calculation is based on the highest EIRP possible from the EUT considering maximum power using the maximum radiated emissions from its internal antennas. The product is not handheld. MPE RATIO CALCULATION PER OET 65 AND KDB 447498 D01 The following information provides the minimum separation distance for the EUT, as calculated from FCC OET 65 Appendix B, Table 1B “Guidelines for General Population/Uncontrolled Exposure” Since only one of 825 or 1900 MHz cellular bands can be transmitting at the same time, two different calculations are needed. The Bluetooth and the 216 MHz radios can be operating with the other transmitters. Calculation for 824-849 MHz GSM Band + Bluetooth and 216 MHz Transmitter MHz Max Power dBm Max Ant Gain dBi Duty Cycle % EIRP W S GP Limit mW/cm^2 MSD meters MPE Ratio from 20 cm Cell at 850 849 31.0 0 50.0 0.6295 0.566 0.0940 0.470 Bluetooth 2400 10.7 0 100.0 0.0117 1.000 0.0097 0.048 Part 95 216 0.8 0 100.0 0.0012 0.200 0.0069 0.035 Total MPE Ratio0.553 Calculation for 1850-1910 MHz Cellular UMTS Band + Bluetooth and 216 MHz Transmitter MHz Max Power dBm Max Ant Gain dBi Duty Cycle % EIRP W S GP Limit mW/cm^2 MSD meters MPE Ratio from 20 cm Cell 1900 28.0 0 50.0 0.3155 1.000 0.0501 0.251 Bluetooth 2400 10.7 0 100.0 0.0117 1.000 0.0097 0.048 Part 95 216 0.8 0 100.0 0.0012 0.200 0.0069 0.035 Total MPE Ratio0.333 Notes on the above tables: a. S is the power density General Population Limit from OET 65 table 1B b. EIRP Power is the Max Power corrected for Antenna Gain and Duty Cycle factor c. MSD (Minimum Separation Distance) = ((EIRP*30)/3770*S))^0.5 d. For mobile or fixed location transmitters, minimum separation distance is 20 cm, even if calculations indicate MPE distance is less. e. The Bluetooth and the 216 MHz part 95 transmitters duty cycle was set to 100%, since the duty cycles are not precisely known. All MPE ratios are less than 1.

Radiometrics Midwest Corporation - www.Radiomet.com Page 1 of 16 Electromagnetic Compatibility Test Report Tests Performed on a CTrack, LLC GPS Tracking Device, Model Recon II Radiometrics Document RP-7869B Product Detail: FCC ID: 2ACNR-RECONII Part 95, 216.025 - 216.975 MHz Low power transmitter Equipment Class: TNB Test Standards: FCC Part 95 CFR Title 47: 2014 This report concerns: Original Grant for Certification FCC Part 95 Subpart G; LPRS operating on 50 kHz extra channels Tests Performed For: Test Facility: CTrack, LLC 8361 East Gelding Dr. Scottsdale, AZ 85260 Radiometrics Midwest Corporation 12 East Devonwood Romeoville, IL 60446 (815) 293-0772 Test Date(s): (Month-Day-Year) July 14 thru August 1, 2014 Document RP-7869B Revisions: Rev. Issue Date Affected Sections Revised By 0 October 13, 2014 Radiometrics Midwest Corporation www.radiomet.com Testing of the CTrack, LLC, Model Recon II, GPS Tracking Device RP-7869B Rev. 0 Page 2 of 16 Table of Contents 1 ADMINISTRATIVE DATA ...................................................................................................................3 2 TEST SUMMARY AND RESULTS .....................................................................................................3 2.1 RF Exposure Compliance Requirements .....................................................................................3 3 EQUIPMENT UNDER TEST (EUT) DETAILS ....................................................................................4 3.1 EUT Description ...........................................................................................................................4 3.1.1 FCC Section 15.203 Antenna Requirements .........................................................................4 3.2 Related Submittals .......................................................................................................................4 4 TESTED SYSTEM DETAILS ..............................................................................................................4 4.1 Tested System Configuration .......................................................................................................4 4.2 Special Accessories .....................................................................................................................4 4.3 Equipment Modifications ..............................................................................................................4 5 TEST SPECIFICATIONS AND RELATED DOCUMENTS..................................................................5 6 RADIOMETRICS’ TEST FACILITIES ................................................................................................. 5 7 DEVIATIONS AND EXCLUSIONS FROM THE TEST SPECIFICATIONS .........................................5 8 CERTIFICATION.................................................................................................................................6 9 TEST EQUIPMENT TABLE ................................................................................................................6 10 TEST SECTIONS..............................................................................................................................6 11 PART 95 TEST PROCEDURES AND RESULTS .............................................................................6 11.1 Occupied Bandwidth; Emissions Masks.....................................................................................6 11.2 Field Strength of Wanted and Unwanted Radiation .................................................................11 11.2.1 Test Procedures.................................................................................................................11 11.2.2 Radiated Emissions Test Results ......................................................................................14 11.3 Frequency Stability ...................................................................................................................15 11.3.1 Frequency Stability Vs Temperature..................................................................................15 11.3.2 Frequency Stability Vs Supply Voltage ..............................................................................16 Notice: This report must not be reproduced (except in full) without the written approval of Radiometrics Midwest Corporation. Radiometrics Midwest Corporation www.radiomet.com Testing of the CTrack, LLC, Model Recon II, GPS Tracking Device RP-7869B Rev. 0 Page 3 of 16 1 ADMINISTRATIVE DATA Equipment Under Test: A CTrack, LLC, GPS Tracking Device Model: Recon II Serial Number: none This will be referred to as the EUT in this Report Date EUT Received at Radiometrics: (Month-Day-Year) Test Date(s): (Month-Day-Year) July 8, 2014 July 14 thru August 1, 2014 Test Report Written By: Test Witnessed By: Joseph Strzelecki Senior EMC Engineer The tests were not witnessed by CTrack, LLC Radiometrics’ Personnel Responsible for Test: Test Report Approved By 10/08/2014 Joseph Strzelecki Senior EMC Engineer NARTE EMC-000877-NE 10/08/2014 Chris W. Carlson Director of Engineering NARTE EMC-000921-NE 2 TEST SUMMARY AND RESULTS The EUT (Equipment Under Test) is a GPS Tracking Device, Model Recon II, manufactured by CTrack, LLC. The detailed test results are presented in a separate section. The following is a summary of the test results. Part 95 Test Results Environmental Phenomena Frequency Range FCC Sections Test Result RF Power Output 216-217 MHz 2.1046 & 95.1013 Pass Bandwidth Limitations & Emissions Masks 216-217 MHz 2.1049 & 95.633 Pass Field Strength of Spurious Radiation; Substitution method 30-2,170 MHz 2.1053 & 95.635 Pass Frequency Stability Vs. Temperature -30 to +50 216-217 MHz 2.1055 & 95.629 Pass Frequency Stability Vs. Voltage 216-217 MHz 2.1055 & 95.629 Pass There are no receive mode tests for the 216 MHz transmitter, since this product is not a receiver below 2.4 GHz. 2.1 RF Exposure Compliance Requirements Since the…

Text truncated - open the document above for the full version.

Authorized Agent: Radiometrics Midwest Corporation (815) 293-0772 Test Setup Photographs Photographs of Radiated Emissions Test Setup Authorized Agent: Radiometrics Midwest Corporation (815) 293-0772 Authorized Agent: Radiometrics Midwest Corporation (815) 293-0772 Photograph of Conducted Emissions Test Setup