2AD3HZ360Z360-Transmitter

Caution! Safety indications: 1.Before operation it is absolutely necessary to read carefully this instruction and especially the safety indications. 2. This remote control device is exclusively meant and authori- zed for the operating of RC-steam models by Wilesco. Wilhelm Schröder GmbH & Co.KG assumes no liability in case of diffe- rent use. 3. For safety reasons, children (recommended age: from 12 years on) should operate this remote control only under supervision of adults. 4. Operating this remote control requires technical knowledge cautious acting. Faults or carelessness during installation and operation can result in considerable damage to property or persons. 5. Also operating the receiving device without the radio transmitter online can cause problems or injuries. 6. In case of abnormal operation it is expressly referred to these dangers, any warranty expires. 7.Each irregularity during operation must exclusively be repaired by a competent and authorized person or by WILESCO themselves. Otherwise any warranty expires. Nonwarranty clause 8. Since it is impossible to control handling, respect of installation and operation hints, application and maintenance, Wilhelm Schröder Gmbh & Co.KG assumes no liability for loss, damages or costs. Any claim for compensation resulting from operation, application or remote damages is refused. No liability is assumed for damages to persons or property or for consequences. 9. Unless legally admitted and regardless of the cause in law the obligation to indemnification is limited to the invoice value of the product which is immediately concerned with the event. 10.It is absolutely necessary to keep this operating instruction. Operating instructions 11. Unscrew the cover ofthebattery compartment and insert a9-V-monobloc battery. Fix the cover withthescrewand screw the antenna in the thread. 12.Switchonthe transmitter(position on). The LED has to come up. The right switch controls the right / left direction, the left switchcontrolsthe forward/backward direction. 13. Unscrew the cover ofthebattery compartmentand insert21,5-V- batteries type AAA (observecorrect polarity+/-).Fixthe cover with the screw. 14.Onlyfor supplementaryset Z363 to steer forward andbackward: connect up the jack plug. 15. The relevant installation instruction is described in the notes of each model (pages 3-6). Use of batteries 16. Non-rechargeable batteries are not to be recharged. 17. Different types of batteries or new and used batteries are not to be mixed. 18. Only batteries of the same or equivalent type as recommended are to be used. 19. Batteries are to be inserted with the correct polarity. 20. Exhausted batteries are to be removed from the toy. 21. Supply terminals are not to be short-circuited. Telecommunication regulations 22. Please observe the telecommunication regulations in the country in which you want to drive your model.Theuserisresponsibleforthedueuseoftheradio remote control. Please observe the legal situation in your country. Indication of waste disposal 23. Environment protection also concerns Wilesco. You have the possibility to return to us the remote control and also the original packing (freight charges arenot reimboursed). All returned remote controls / packing are professionally recycled. You can also dispose of the electronic components professionally and according to the legal prescriptions yourself by taking them to the recycle boxes in your community. This model is meant for the above described purpose only. Technical specifications subject to change without prior notice. Schützenstraße 12E-Mail: [email protected] D-58511 Lüdenscheidwww.wilesco.de Remote Remote Control Z360 forward backward only with supplement Z363 rightleft only with supplement Z363 Demontage der KettenlenkungSchraube gemäß Abbildung herausschrauben. Disassembly of the chain steeringScrew off the screw according to the picture. Demontage der Kettenlenkung Steuereinheit aus der Halterung lösen und die Federn aus dem Abstreifbügel aushaken. Disassembly of the chain steering Demount the steering unit off the bracket and unclasp the spring out of the scraper harness. Bohrung für neuen Lenkdraht:2-mm-Loch für den Lenkdraht bohren. Die Position ist dem Bild zu entnehmen.Achtung: Das Loch nur durch das oberste Blech bohren. Drill-hole for the new steering wheel:Drill a hole of 2 mm diameter for the steering wheel. You can see the location on the picture.Watch: drill the hole only through the top metal sheet. Montage des Empfängermoduls Die Schraube M 2,5 herausdrehen. (Die sich hier befindliche Unterlegscheibe wird später an an- derer Stelle noch benötigt.) Assembly of the receiver module Unscrew the screw M 2,5. (The washer of this screw will be used later on in another place.) Montage des Empfängermoduls Die beiden Muttern der Dachbügel unter dem Führerhaus lösen und das schwarze Schutzblech auf- setzen. Die linke Mutter mit beiliegendem Maulschlüssel wieder anziehen. Rechts den Sicherungs- ring, anschließend den Kabelanschluss des Empfängermoduls auflegen und mit der Mutter (Nr. 2) festziehen. Assembly of the receiver module Loosen both screw nuts and roof-legs below the driver¶s cab and place the black protection shield. Screw the the left nut with the enclosed wrench. Place the locking ring and then the cable junction of the receiver box on the right side and fix it with screw No. 2. Schützenstraße 1258511 LüdenscheidE-Mail: [email protected] Montage des Empfängermoduls Das Empfängermodul oben einhängen und unten heranschieben gemäß Bild. Assembly of the receiver module Hang the top of the receiver box and push the bottom according to the picture. Montage Fernsteuerung Z360 für DampfwalzeÄOld Smoky³D365 / D366 / D368 Zusatzblatt zur Bedienungsanleitung / Beides unbedingt aufbewahren? Assembly of the radio remote control Z360 for steam rollersÄOld Smoky³D365 / D366 / D368 Supplement to the manual, please keep both! Sender und Empfängerbox mit Batterien bestücken. Fill the transmitter and…

Text truncated - open the document above for the full version.

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 Wilhelm Schroeder GmbH&Co.KG-Metallwarenfabrik 2015-01-21 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID:2AD3HZ360 We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Schematics - Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature : Client’s name / title : Thomas Schroeder / Manager Contact information / address: Schuetzenstrasse 12 D-58511 Luedenscheid

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AD3HZ360 Report No.: LCS1412030157E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 3 1. EXTERIOR PHOTOGRAPHS OF EUT Fig.1 Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AD3HZ360 Report No.: LCS1412030157E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 3 Fig.3 Fig.4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AD3HZ360 Report No.: LCS1412030157E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 3 Fig.5 Fig.6

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD FCC ID: 2AD3HZ360 Report No.: LCS1412030157E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1 LABEL AND LOCATION Size:L:4cm*W:2cm Wilhelm Schroeder GmbH&Co.KG-Metallwarenfabrik The Transmitter will be labelled “Z360-Transmitter” FCC ID: 2AD3HZ360 Model No.: Z360 Caution: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Label location

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AD3HZ360 Report No.: LCS1412030157E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 2 1. INTERIOR PHOTOGRAPHS OF EUT Fig.1 Fig.2 Antenna SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AD3HZ360 Report No.: LCS1412030157E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 2 Fig.3 Fig.4

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AD3HZ360 Report No.: LCS1412030157E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 22 FCC TEST REPORT For Wilhelm Schroeder GmbH&Co.KG-Metallwarenfabrik The Transmitter will be labelled "Z360-Transmitter" Model No.: Z360 Prepared for : Wilhelm Schroeder GmbH&Co.KG-Metallwarenfabrik Address : Schuetzenstrasse 12 D-58511 Luedenscheid Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd. Address : 1/F., Xingyuan Industrial Park, Tongda Road, Bao’an Avenue, Bao’an District, Shenzhen, Guangdong, China Date of receipt of test sample : December 01, 2014 Number of tested samples : 1 Serial number : Prototype Date of Test : December 01, 2014– December 20, 2014 Date of Report : December 20, 2014 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AD3HZ360 Report No.: LCS1412030157E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 22 FCC TEST REPORT FCC CFR 47 PART 15 C(15.229): 2013 Report Reference No. .............. : LCS1412030157E Date of Issue ................................ : December 20, 2014 Testing Laboratory Name ......... : Shenzhen LCS Compliance Testing Laboratory Ltd. Address ........................................ : 1/F., Xingyuan Industrial Park, Tongda Road, Bao’an Avenue, Bao’an District, Shenzhen, Guangdong, China Testing Location/ Procedure ........ : Full application of Harmonised standards ■ Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name ....................... : Wilhelm Schroeder GmbH&Co.KG-Metallwarenfabrik Address ........................................ : Schuetzenstrasse 12 D-58511 Luedenscheid Test Specification Standard ....................................... : FCC CFR 47 PART 15 Subpart C : 2013, ANSI C63.4-2009 Test Report Form No. ................ : LCSEMC-1.0 TRF Originator ............................ : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF .................................. : Dated 2011-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test Item Description. ............... : The Transmitter will be labelled "Z360-Transmitter" Trade Mark .................................. : Wilesco Model/ Type reference ................. : Z360 Ratings ......................................... : DC 9V by Battery Result ......................................... : Positive Compiled by: Supervised by: Approved by: Tree Zhan/ File administrators Danny Huang/ Technique principal Gavin Liang/ Manager SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AD3HZ360 Report No.: LCS1412030157E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 22 FCC--TEST REPORT Test Result Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Test Report No. : LCS1412030157E December 20, 2014 Date of issue Type / Model........................... : Z360 EUT......................................... : The Transmitter will be labelled "Z360-Transmitter" Applicant............................... : Wilhelm Schroeder GmbH&Co.KG-Metallwarenfabrik Address.................................. : Schuetzenstrasse 12 D-58511 Luedenscheid Telephone............................... : / Fax.......................................... : / Manufacturer........................ : Wilhelm Schroeder GmbH&Co.KG-Metallwarenfabrik Address................................... : Schuetzenstrasse 12 D-58511 Luedenscheid Telephone............................... : / Fax.......................................... : / Factory................................... : Wilhelm Schroeder GmbH&Co.KG-Metallwarenfabrik Address................................... : Schuetzenstrasse 12 D-58511 Luedenscheid Telephone............................... : / Fax.......................................... : / SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID:2AD3HZ360 Report No.: LCS1412030157E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 4 of 22 TABLE OF CONTENTS 1. GENERAL INFORMATION .................................................................................................................................. 5 1.1. DESCRIPTION OF DEVICE (EUT) ........................................................................................................................... 5 1.2. OBJECTIVE ............................................................................................................................................................ 5 1.3. ENVIRONMENTAL CONDITIONS............................................................................................................................. 5 1.4. HOST SYSTEM CONFIGURATION LIST AND DETAILS ............................................................................................. 6 1.5. EXTERNAL I/O PORT ............................................................................................................................................. 6 1.6. EUT OPERATION .................................................................................................................................................. 6 1.7. ANTENNA SYSTEM ........…

Text truncated - open the document above for the full version.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AD3HZ360 Report No.:LCS1412030157E _______________________________________________________________________________________________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 1 1. TEST SETUP PHOTOGRAPHS 1.1. Photo of Radiated Emissions Measurement Fig.1 Fig.2