2AD3T-LTC3201television set

R Te c h nology, Ltd. Model:LTC3201 User’s Manual 1080i 1 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE WITH THE FCC RULES COULD AVOID THE USERS AUTHORITY TO OPERATE THIS EQUIPMENT. Caution: To reduce the risk of electric shock, do not remove cover or back. No user-serviceable parts inside. Refer servicing to qualified service personnel. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Caution and Warning FCC Caution The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product enclosure that may be of sufficient magnitude to consitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the TV. FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guaran- tee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. 25. If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA NO.70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrodes. (See Diagram Safety Precautions ANTENNA LEAD IN WIRE GROUND CLAMP GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PARTH) ELECTRIC SERVICE EQUIPMEN T ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) Diagram Figure A 3 4 18 5 28 Wall Mounting Unit Specication Product Specication Lock Menu 26 Audio Menu Time Menu 30 Channel Menu 32 USB Menu 34 36 37 38 If you Choose Your Connections TV LTC3200LED supports various of connecting ways from other devices (such as DVD, VCR, Set-top box, ect.). Please follow the table sheet to choose the cables which adapt to your device. . HDMI(TM) cable Note:HDMI,the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC Caution: Unplug the AC cord when you connect other devices to TV. Cable Connections Cables AV In, Audio In L and R HDMI-1, 2, 3 VGA ,Audio Audio Cable Audio cable with 3.5mm terminal VGA cable COMPONENT video cable Go to page 8 AV/Audio cable Go to page 9 Go to page 10 Go to page 11 7 Component In, Audio Out L and R Audio LR Audio Video HDMI To connect an composite AV device, such as a DVD player, follow these steps: 1. Connect the Video-In jack on the back of TV to the video output jacks of device via video cable (yellow). 2. Connect the Audio-In L and R jacks on the back of TV to the audio output jacks of device via audio cable. Notice the left channel jack and plugs are white and the right channel jack and plugs are red. Note: AV signal belongs to composite video. This kind of video signal has regular good display quality. Composite Video Connection The picture below is an example of a connection using the composite video jack. 8 The back of TV The output panel of other device Connecting AV Composite device (Good Video Quality) R LPr Pb Y Audio -3 Audio RYPbPr Video HDMI 9 The back of TV Note: Y/Pb/Pr jacks are component video. This kind of video signal has better display quality. Component Video Connection The picture below is an example of a connection using the component video jack. L Audio LR Audio LRPbPr Video HDMI To connect an HDMI device, such as a DVD player, Please Connect the HDMI-1,2or3 jack on the back of TV to the out Put jacks of device via HDMI cable. Note: HDMI(High-Definition Multimedia Interface) is a compact audio/video interface for transmitting uncompr essed digital data. It carries the audio and video signal via the same cable and has the best display qual ity. The picture below is an example of a connection using the HDMI video jack. Connecting HDMI device (Best Video Quality) L VGA Speaker or To connect a computer, follow these steps: 1. Connect the VGA port on the back of TV to the VGA output jack of device via D-sub 15-pin cable. 2. Connect the PC Audio In jack on the back of TV to the audio output jack of computer with audio cable (3.5mm). Note: If you wa…

Text truncated - open the document above for the full version.

Date:0/05/2015 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD FCC ID:2AD3T-LTC3201 To Whom It May Concern: We, Dayton Electronic(HK) Co.,Ltd. are applying FCC DOC for product television setwhich model no. is LTC3201, LTC4001, TV43LEDWR, TV55LEDWR, TV58LEDWR, TV65LEDWR, TV75LEDWR, TV80LEDWR, CT-2220, CT-2420, CT-3220, CT-4020, CT-4820. the FCC DOC is doing at proper FCC authorized and recognized lab, and FCC DOC will be issued soon. If you have any question or concerns, pls. contact us. Sincerely, Client’s signature Cl ient’s name / title YU Zhou / ENGINEER Contact information / address Tel: 15986760609 Address: 7/F KIN ON COMMERCIAL BUILDING 49-51 JERVOIS STREET SHEUNG WAN, HK recognized MRA lab, and FCC DOC will be issued soon.

Dayton Electronic(HK) Co.,Ltd 7/F KIN ON COMMERCIAL BUILDING 49-51 JERVOIS STREET SHEUNG WAN, HK 2015-01-30 Equipment Authorization Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AD3T-LTC3201 Product Name: television set Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:  Schematics  Block diagram  Operational Description  BOM These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 01/30/2015 By: YU ZHOU Signature Printed Title: ENGINEER On behalf of : Dayton Electronic(HK) Co.,Ltd Telephone: 15986760609

NOTE: 1.印刷版面见上图； 2.尺寸： 3.材质：50#PET带不干背胶,改成黑色消银龙 (材质需经过UL认证) 4.底色： 黑色 字体颜色： 银色 5.印刷不可有溢墨及颜色不均匀等不良现象 6.裁边须完整 7.条形码根据编码规则由相关部门负责打印，条形码规格参见相应图纸 8.粘力：将label切成25mm宽，异端粘贴于钢板上，以180°方向的力拉胶带另一端，所得拉力即为粘 力。用粘力测试仪进行测试。 9.正常耐温测试：在钢板上耐温范围为-20~100°C，在80~100°C保持8小时后无翘角分层脱落起泡等不 良现象；在塑胶、纸箱上耐温范围为-20~65°C，在65°C保持8小时后无翘角分层脱落起泡等不良现象； 10.耐温湿度循环测试：循环条件：贴在塑胶咬花面（PET）贴在塑胶咬花面/纸箱（铜版纸）：温度 -20~60°C，湿度30%~90%，时间 96小时后无翘角分层脱落起泡等不良现象。 4.底色： （1）所有原材料及辅助材料必须符合ROHS的有关规定 （2）必须符合ROHS要求： 镉+铅+六价铬+汞<100ppm； 镉<5ppm,PBB<1000ppm/PBDE<1000ppm 3.材质：50#PET带不干背胶 黑色银色 1.印刷版面见上图； （1）所有原材料及辅助材料必须符合ROHS的有关规定 （2）必须符合ROHS要求： 镉+铅+六价铬+汞<100ppm； 镉<5ppm,PBB<1000ppm/PBDE<1000ppm ≤ LTC3201 DA32S114300001 2014.12.30 69.5 47.5 此处为工厂打印 LTC3201 ≤ LTC3201 2015.01.08 SeniorTV Technology, Ltd. SeniorTV Technology, Ltd. FCC ID:2AD3T-LTC3201 FCC ID:2AD3T-LTC3201

Label location

FCC ID: 2AD3T-LTC3201 According to 447498 D01 General RF Exposure Guidance v05 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where --f(GHz) is the RF channel transmit frequency in GHz --Power and distance are rounded to the nearest mW and mm before calculation --The result is rounded to one decimal place for comparison eirp = pt x gt = (EXd) 2 /30 where: pt = transmitter output power in watts, gt = numeric gain of the transmitting antenna (unitless), E = electric field strength in V/m, --- 10 ((dBuV/m)/20) /10 6 d = measurement distance in meters (m) ---3m So pt = (EXd) 2 /30 x gt Field strength = 96.48dBuV/m @3m Ant gain =0dBi, so Ant numeric gain= 1.0 So pt={ [10 (96.48) /10 6 x 3] 2 /30x1.0 }x1000 mW = 1.589mW So (1.589 mW /5mm)x √2.48 = 0.454<3 Then SAR evaluation is not required

Global United Technology Services Co., Ltd. Report No.: GTSE15010008601 Authorized Signature: Robinson Lo Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the GTS product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of GTS or testing done by GTS in connection with, distribution or use of the product described in this report must be approved by GTS in writing. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. FCC REPORT Applicant: Dayton Electronic(HK) Co.,Ltd Address of Applicant: 7/F KIN ON COMMERCIAL BUILDING 49-51 JERVOIS STREET SHEUNG WAN, HK Equipment Under Test (EUT) Product Name: television set Model No.: LTC3201, LTC4001, TV43LEDWR, TV55LEDWR, TV58LEDWR, TV65LEDWR, TV75LEDWR, TV80LEDWR, CT-2220, CT-2420, CT-3220, CT-4020, CT-4820 Trade Mark: SENIOR TV, WR, RCA, continu us FCC ID: 2AD3T-LTC3201 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.249:2013 Date of sample receipt: January 19, 2015 Date of Test: January 22-39, 2015 Date of report issued: January 29, 2015 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Report No.: GTSE15010008601 Global United Technology Services Co., Ltd. Project No.: GTSE150100086RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 2 of 36 2 Version Version No. Date Description 00 January 29, 2015 Original Prepared By: Date: January 29, 2015 Project Engineer Check By: Date: January 29, 2015 Reviewer Report No.: GTSE15010008601 Global United Technology Services Co., Ltd. Project No.: GTSE150100086RF 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District, Shenzhen, China 518102 Telephone: +86 (0) 755 2779 8480 Fax: +86 (0) 755 2779 8960 Page 3 of 36 3 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 VERSION .................................................................................................................................................. 2 3 CONTENTS .............................................................................................................................................. 3 4 TEST SUMMARY ..................................................................................................................................... 4 5 GENERAL INFORMATION ...................................................................................................................... 5 5.1 CLIENT INFORMATION ......................................................................................................................... 5 5.2 GENERAL DESCRIPTION OF EUT ......................................................................................................... 5 5.3 TEST MODE ........................................................................................................................................ 7 5.4 DESCRIPTION OF SUPPORT UNITS ....................................................................................................... 7 5.5 TEST FACILITY .................................................................................................................................... 7 5.6 TEST LOCATION ................................................................................................................................. 7 5.7 OTHER INFORMATION REQUESTED BY THE CUSTOMER ......................................................................... 7 6 TEST INSTRUMENTS LIST ..................................................................................................................... 8 7 TEST RESULTS AND MEASUREMENT DATA ...................................................................................... 9 7.1 ANTENNA REQUIREMENT ..................................................................................................................... 9 7.2 CONDUCTED EMISSIONS ................................................................................................................... 10 7.3 RADIATED EMISSION METHOD ........................................................................................................... 13 7.3.1 Field Strength of The Fundamental Signal ................................................................................ 15 7.3.2 Spurious emissions .................................................................................................................... 16 7.3.3 Bandedge emissions.................................................................................................................. 20 7.4 20DB OCCUPY BANDWIDTH .............................................................................................................. 21 8 TEST SETUP PHOTO ............................................................................................................................ 23 9 EUT CONSTRUCTIONAL DETAILS .........................................................…

Text truncated - open the document above for the full version.

Radiated Emission Conducted Emissions