2AD9Q-X4C007Ultra Wide Band (UWB) Radar sensor module

X4C007 - Datasheet Ultra Wideband (UWB) Impulse Radar Sensor Rev. C - Advance - TBD-2020 Key Features • Complete Ultra Wideband (UWB) impulse radar sensor module. • Accurate human presence detection with very high sensitivity. • Programmable detection range from 0.3 to 1.6 m. • Sees through any material except metal, operates at sub 10 GHz. • Low power consumption, typically less than 2 mW in No Presence state. • Advanced power management enabling low power duty cycle controlled operation. • Industrial operating temperature range, -40°C to +85°C. • Designed for world-wide regulatory compliance. • Bi-phase coding of transmitted pulses for spectrum spreading. • Built-in antennas, no external circuitry required. • I2C interface for small form factor systems. • Requires few external components enabling small form-factor systems with low BOM cost. Product Description The X4C007 is an Ultra Wideband (UWB) short-range impulse radar sensor module, designed for unlicensed operation in world-wide markets.The X4C007 contains all required circuitry, such as antennas, clocks, etc. and can be connected directly to existing systems through a standard I2C interface. The X4C007 sensor is extremly sensitive and can detect human presence based on respiration motion alone. The sensor accurately detects presence within the detection zone and has fully configurable range limits. The sensor reports presence state as well as range to target when presence is detected. Applications • Human presence detection for computing devices such as laptops, 2-in-1s, monitors, etc. Ordering Information For orders, please contact Novelda sales through the contact form on our webpage: https://www.novelda.com TBD-2020 Page 1 of 13 Rev. C - Advance Copyright © 2019-2020 Novelda ASwww.novelda.com X4C007 - Datasheet Table of Contents 1. Electrical Characteristics.................................................................................................................... 3 1.1. Absolute Maximum Ratings...................................................................................................... 3 1.2. General Operating Conditions.................................................................................................. 3 1.3. Current Consumption.............................................................................................................. 3 1.4. Specification of Clock Sources................................................................................................. 3 1.4.1. Internal Low Power Oscillator (LPOSC).......................................................................... 3 1.4.2. Crystal Oscillator (XOSC)............................................................................................. 3 2. Inter-Integrated Circuit (I2C)............................................................................................................... 5 2.1. I2C Specification..................................................................................................................... 5 2.2. I2C Commands....................................................................................................................... 5 2.2.1.Writing commands and data.......................................................................................... 5 2.2.2. Reading data................................................................................................................ 5 3. Implementation and Layout................................................................................................................. 6 3.1.Typical Application Circuit......................................................................................................... 6 3.2. Mechanical Specifications........................................................................................................ 6 3.2.1. Physical Dimension and Pinout...................................................................................... 6 3.2.2. Product Integrations Guidelines..................................................................................... 8 4. Regulatory Compliance Notices.......................................................................................................... 9 4.1. United States (FCC) Regulatory Notices................................................................................... 9 4.1.1. UWB Device Notice...................................................................................................... 9 4.1.2. Modification Statement................................................................................................. 9 4.1.3. Interference Statement.................................................................................................. 9 4.1.4. RF Exposure................................................................................................................ 9 4.1.5. FCC Class B Digital Device Notice................................................................................. 9 4.1.6. Compliance of Host Devices.......................................................................................... 9 4.1.7. Labelling requirements for the Host Device................................................................... 10 4.2. Canada (ISED) Regulatory Notices......................................................................................... 10 4.2.1. Modification Statement................................................................................................ 10 4.2.2. Interference Statement................................................................................................ 10 4.2.3. RF Exposure.............................................................................................................. 10 4.2.4. Labelling Requirements for the Host Device................................................................. 10 4.2.5. CAN ICES-003(B)...............................................................…

Text truncated - open the document above for the full version.

Oslo Novelda AS Gjerdrumsvei 8 0484 Oslo Norway Kviteseid Novelda AS Garverivegen 2 3850 Kviteseid Norway Trondheim Novelda AS Rotvoll alle 2 7053 Trondheim Norway Date: Wednesday, March 18, 2020 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Rd. Columbia MD 21046 Ref: Agent letter for FCC ID: 2AD9Q-X4C007 We, Novelda AS Garverivegen 2, Kviteseid, 3850, Norway hereby authorize, DEKRA Testing and Certification, S.A.U. C/Severo Ochoa 2, 29590 Campanillas Agent: Álvaro Corrales Sedeño, e-mail: [email protected] Phone: +34 925 619 198 to act as our agent in the preparation of this application for equipment certification, including the signing of all documents relating to these matters. We also hereby certify that neither we nor any party to this application are subject to a denial of U.S. Federal benefits, which include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, U.S.C. 862 because of conviction for possession or distribution of controlled substance. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by DEKRA Testing and Certification, S.A.U., still resides with us. This agreement expires one year from the current date. Sincerely, By: Dag T. Wisland Title: CTO Company: Novelda AS Telephone: +47 91 36 76 79 e-mail: [email protected]

FCB012_02 //DEKRA Testing and Certification, S.A.U. // www.dekra-product-safety.com/wireless Date: April 13th 2020 DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía C/ Severo Ochoa 2 & 6 29590 Campanillas Málaga, España Ref: Confidentiality request for FCC ID: 2AD9Q-X4C007 To whom it may concern: Pursuant to §0.457(d)(1)(ii) and §0.459 of the Commission’s Rules (47 C.F.R.) and §552 (b)(4) of the Freedom of Information Act, Novelda AS hereby request requests that a part of the subject FCC application be held confidential to avoid release of sensitive information of the product to the public. For the product stated above, we request that the following information be withheld from public disclose: Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Internal Photos Short Term Permanent Operation Description Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term User’s Manual Permanent Confidentiality: The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to us and provide unjustified benefits to our competitors. Short-Term Confidentiality: We hereby request short-term confidentiality for the product stated above to avoid premature release of sensitive information prior to marketing or release of the product to the public. Release date of short term confidentiality is: 45 days from grant date marked 90 days from grant date marked 135 days from grant date marked 180 days from grant date marked Specific date: We are also aware that we are responsible to notify DEKRA in the event information regarding the product or the product is made available to the public. DEKRA will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Sincerely, PA __________________________ By: Dag Wisland Title: CTO Company: Novelda AS Telephone: +47 91 36 76 79 e-mail: [email protected]

FCB013_02 //DEKRA Testing and Certification, S.A.U. // www.dekra-product-safety.com/wireless Date: April 13th 2020 DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía C/ Severo Ochoa 2 & 6 29590 Campanillas Málaga, España Ref: FCC Modular approval letter for FCC ID: 2AD9Q-X4C007 To whom it may concern: The following attestation addresses the requirements to support modular approval pursuant to §15.212 of the Commission’s Rules: Modular approval requirement Yes No* (i) The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. X (ii) The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with part 15 requirements under conditions of excessive data rates or over-modulation. X (iii) The modular transmitter must have its own power supply regulation. X (iv) The modular transmitter must comply with the antenna and transmission system requirements of §§15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of §15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. X (v) The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in §15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see §15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see §15.31(i)). X (vi) The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. X (vii) The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. X (viii) The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. X * Shall provide a detailed explanation if the answer is “No”. Sincerely, PA __________________________ By: Dag Wisland Title: CTO Company: Novelda AS Telephone: +47 91 36 76 79 e-mail: [email protected]

1 Lidia Vega Pérez De:[email protected] Enviado el:martes, 21 de abril de 2020 18:43 Para:Alvaro Corrales Sedeño Asunto:Response to Inquiry to FCC (Tracking Number 814388) Inquiry on 04/20/2020 : Inquiry: Dear, We hereby request permission to not place the FCC ID requested for this module which we want to get approval for. The module is 4 mm x 32 mm and it's impractical for it to be marked. the FCC ID will be informed to integrators in the installation instructions along with the requirements to place on the host device (marked or in a label) the text "Contains FCC ID: 2AD9Q-X4C007" Thank you very much. FCC response on 04/21/2020 The FCC will allow if you meet the requirement in KDB publication 784748 number 3 Certification. Attachment Details: Do not reply to this message. Please select the Reply to an Inquiry Response link from the OET Inquiry System to add any additional information pertaining to this inquiry.

Back Front

DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29 507 456 Report No: (NIE) 62699RAN.002A1 2020-06-11 Test report No: NIE: 62699RAN.002A1 Assessment report RF EXPOSURE REPORT ACCORDING TO FCC 47 CFR Part 2.1091 FCC 47 CFR Part 2.1093 (*) Identification of item under evaluation Ultra Wide Band (UWB) Radar sensor module (*) Trademark Novelda (*) Model and /or type reference X4C007 Other identification of the product FCC ID: 2AD9Q-X4C007 IC: 22782-X4C007 HW version: Rev. 4.0 SW version: 12c04720 (*) Features N/A Manufacturer Novelda AS Garverivegen 2, NO-3850 Kviteseid, Norway Test method requested, standard FCC 47 CFR Part 2.1091 Radiofrequency radiation exposure evaluation: mobile devices. FCC 47 CFR Part 2.1093. Radiofrequency radiation exposure evaluation: portable devices. IEEE Std C95.3 TM -2002 (R2008). IEEE Recommended Practice for Measurements and Computations of Radio Frequency Electromagnetic Fields With Respect to Human Exposure to Such Fields, 100 kHz–300 GHz Summary IN COMPLIANCE Approved by (name / position & signature) Rafael López EMC Consumer & RF Lab. Manager Date of issue 2020-06-11 Report template No FAN36_01 (*) “Data provided by the client” DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29 507 456 Report No: (NIE) 62699RAN.002A1 Page 2 of 6 2020-06-11 Index Competences and guarantees .................................................................................................... 3 General conditions ...................................................................................................................... 3 Data provided by the client .......................................................................................................... 3 Identification of the client............................................................................................................. 3 Document history ........................................................................................................................ 3 General description of the device under evaluation ..................................................................... 4 RF Exposure Assessment result and verdict ............................................................................... 4 Appendix A: FCC RF Exposure information ................................................................................ 5 FCC RF Exposure evaluation ................................................................................................. 6 DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29 507 456 Report No: (NIE) 62699RAN.002A1 Page 3 of 6 2020-06-11 Competences and guarantees In order to assure the traceability to other national and international laboratories, DEKRA Testing and Certification, S.A.U. has a calibration and maintenance program for its measurement equipment. DEKRA Testing and Certification, S.A.U. guarantees the reliability of the data presented in this report, which is the result of the measurements and the tests performed to the item under test on the date and under the conditions stated on the report and, it is based on the knowledge and technical facilities available at DEKRA Testing and Certification, S.A.U. at the time of performance of the test. DEKRA Testing and Certification, S.A.U. is liable to the client for the maintenance of the confidentiality of all information related to the item under test and the results of the test. The results presented in this Assessment Report apply only to the particular item under test established in this document. IMPORTANT: No parts of this report may be reproduced or quoted out of context, in any form or by any means, except in full, without the previous written permission of DEKRA Testing and Certification, S.A.U. General conditions 1. This report is only referred to the item that has undergone the assessment. 2. This report does not constitute or imply on its own an approval of the product by the Certification Bodies or competent Authorities. 3. This document is only valid if complete; no partial reproduction can be made without previous written permission of DEKRA Testing and Certification, S.A.U. 4. This test report cannot be used partially or in full for publicity and/or promotional purposes without previous written permission of DEKRA Testing and Certification, S.A.U. and the Accreditation Bodies Data provided by the client The following data has been provided by the client: 1. Information relating to the description of the sample ("Identification of the item tested", "Trademark", "Model and/or type reference tested). 2. Maximum output power and maximum antenna gain information. DEKRA Testing and Certification S.A.U. declines any responsibility with respect to the information provided by the client and that may affect the validity of results. Identification of the client Novelda AS Garverivegen 2, NO-3850 Kviteseid, Norway Document history Report number Date Description 62669RAN.002 2020-03-25 First release 62699RAN.002A1 2020-06-11 Second release. Maximum output power and antenna gain updated. Assessment evaluation updated according to CB requirements. This modification test report cancels and replaces the test report 62669RAN.002. DEKRA Testing and Certification, S.A.U. Parque Tecnológico de Andalucía, c/ Severo Ochoa nº 2 · 29590 Campanillas · Málaga · España C.I.F. A29 507 456 Report No: (NIE) 62699RAN.002A1 Page 4 of 6 2020-06-11 General description of the device under evaluation The device under evaluation consists of an Ultra Wide Band (UWB) Radar sensor module. The equipment specifications declared by the manufacturer for the supported technology are: Technology Band Frequency (MHz) Maximum Conducted Output Power RMS Frame (dBm) Antenna peak gain…

Text truncated - open the document above for the full version.

DEKRA Certification, Inc. 405 Glenn Dr. Suite 12, Sterling, VA 20164 United States of America Report No: 2711ERM.002A2 06-10-2020 FCC LISTED, REGISTRATION NUMBER: 2764.01 ISED LISTED REGISTRATION NUMBER: 23595-1 Test report No: 2711ERM.002A2 Test report USA FCC 15.519/FCC 15.521 CANADA RSS-220 RF Measurement of Ultra-Wideband (UWB) devices operating within the band 3100 MHz and 10600 MHz. Identification of item tested Ultra Wide Band (UWB) Radar Sensor module Trademark Novelda Model and /or type reference X4C007 Other identification of the product FCC ID: 2AD9Q-X4C007 IC: 22782-X4C007 Features --- Manufacturer Novelda AS Garverivegen 2 NO-3850 Kviteseid, Norway Test method requested, standard FCC CFR Title 47 Part 15 Subpart F: 2015 CANADA RSS-220 Issue 1 (July 2018). RSS-GEN Issue 5 (March 2019) ANSI C63.10-2013: American National Standard for Testing Unlicensed Wireless Devices. Summary IN COMPLIANCE Approved by (name / position & signature) Domingo Galvez EMC&RF Lab Manager Date of issue 06-10-2020 Report template No FDT08_21 DEKRA Certification, Inc. 405 Glenn Dr. Suite 12, Sterling, VA 20164 United States of America Report No: 2711ERM.002A2 Page 2 of 31 06-10-2020 Index Competences and guarantees ................................................................................................... 3 General conditions ..................................................................................................................... 3 Uncertainty ................................................................................................................................. 3 Data provided by the client ......................................................................................................... 4 Usage of samples ...................................................................................................................... 4 Test sample description ............................................................................................................. 6 Identification of the client ............................................................................................................ 7 Testing period and place ............................................................................................................ 7 Document history ....................................................................................................................... 7 Modifications to the reference test report .................................................................................... 8 Environmental conditions ........................................................................................................... 8 Remarks and comments ............................................................................................................ 8 Testing verdicts .......................................................................................................................... 9 Summary .................................................................................................................................... 9 List of equipment used during the test ...................................................................................... 10 Appendix A: Test results .......................................................................................................... 11 DEKRA Certification, Inc. 405 Glenn Dr. Suite 12, Sterling, VA 20164 United States of America Report No: 2711ERM.002A2 Page 3 of 31 06-10-2020 Competences and guarantees DEKRA Certification Inc. is a testing laboratory accredited by A2LA (The American Association for Laboratory Accreditation), to perform the tests indicated in the Certificate 2764.01 DEKRA Certification Inc. is a testing laboratory competent to carry out the tests described in this report. In order to assure the traceability to other national and international laboratories, DEKRA Certification Inc. has a calibration and maintenance program for its measurement equipment. DEKRA Certification Inc. guarantees the reliability of the data presented in this report, which is the result of the measurements and the tests performed to the item under test on the date and under the conditions stated on the report and, it is based on the knowledge and technical facilities available at DEKRA Certification at the time of performance of the test. DEKRA Certification Inc. is liable to the client for the maintenance of the confidentiality of all information related to the item under test and the results of the test. The results presented in this Test Report apply only to the particular item under test established in this document. IMPORTANT: No parts of this report may be reproduced or quoted out of context, in any form or by any means, except in full, without the previous written permission of DEKRA Certification Inc. General conditions 1. This report is only referred to the item that has undergone the test. 2. This report does not constitute or imply on its own an approval of the product by the Certification Bodies or competent Authorities. 3. This document is only valid if complete; no partial reproduction can be made without previous written permission of DEKRA Certification Inc. 4. This test report cannot be used partially or in full for publicity and/or promotional purposes without previous written permission of DEKRA Certification Inc. and the Accreditation Bodies. Uncertainty Uncertainty (factor k=2) was calculated according to the DEKRA Certification internal document PODT000. Frequency (MHz) U (k=2) Units 30-180 3.82 dB 180-1000 2.61 dB 1000-18000 2.92 dB 18000-40000 2.15 dB DEKRA Certification, Inc. 405 Glenn Dr. Suite 12, Sterling, VA 20164 United States of America Report No: 2711ERM.002A2 Page 4 of 31 06-10-2020 Data provided by the client Ultra-Wide Band (UWB) Radar sensor module. DEKRA declines any responsibility with respect to the information provided by the client and that may affect the validity of results. Us…

Text truncated - open the document above for the full version.

DEKRA Certification, Inc. 405 Glenn Dr. Suite 12, Sterling, VA 20164 United States of America Report No: Page 1 of 4 03-18-2020 Appendix B: Photographs DEKRA Certification, Inc. 405 Glenn Dr. Suite 12, Sterling, VA 20164 United States of America Report No: Page 2 of 4 03-18-2020 Figure B1: Test Sample Figure B2: Radiated Low range Setup 9 kHz – 30 MHz. DEKRA Certification, Inc. 405 Glenn Dr. Suite 12, Sterling, VA 20164 United States of America Report No: Page 3 of 4 03-18-2020 Figure B3: Radiated Low range Setup 30 – 960 MHz Figure B4: Radiated High range Setup 960 MHz – 18 GHz DEKRA Certification, Inc. 405 Glenn Dr. Suite 12, Sterling, VA 20164 United States of America Report No: Page 4 of 4 03-18-2020 Figure B5: Radiated High range Setup 18 – 40 GHz