2ADGA-WT4100WT4100 series Long Range Wireless Transmitters

WT4100 series / WT4200 series Long-range RF wireless devices User manual 7EN02-0360-00 08/2015 7EN02-0360-003 Safety information Important information Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service or maintain it. The following special messages may appear throughout this bulletin or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure. The addition of either symbol to a “Danger” or “Warning” safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Please note Electrical equipment should be installed, operated, serviced and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material. A qualified person is one who has skills and knowledge related to the construction, installation, and operation of electrical equipment and has received safety training to recognize and avoid the hazards involved. DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE NOTICE is used to address practices not related to physical injury. 7EN02-0360-004 Notices Legal information The Schneider Electric brand and any registered trademarks of Schneider Electric Industries SAS referred to in this guide are the sole property of Schneider Electric SA and its subsidiaries. They may not be used for any purpose without the owner's permission, given in writing. This guide and its content are protected, within the meaning of the French intellectual property code (Code de la propriété intellectuelle français, referred to hereafter as "the Code"), under the laws of copyright covering texts, drawings and models, as well as by trademark law. You agree not to reproduce, other than for your own personal, noncommercial use as defined in the Code, all or part of this guide on any medium whatsoever without Schneider Electric’s permission, given in writing. You also agree not to establish any hypertext links to this guide or its content. Schneider Electric does not grant any right or license for the personal and noncommercial use of the guide or its content, except for a non-exclusive license to consult it on an "as is" basis, at your own risk. All other rights are reserved. Electrical equipment should be installed, operated, serviced and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material. As standards, specifications and designs change from time to time, please ask for confirmation of the information given in this publication. FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. The user is cautioned that any changes or modifications not expressly approved by Schneider Electric could void the user’s authority to operate the equipment. This digital apparatus complies with CAN ICES-3 (B) /NMB-3(B). This device complies with FCC radiation exposure limits set forth for general population. This device must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. 7EN02-0360-005 Industry Canada This device complies with Industry Canada RF radiation exposure limits set forth for general population. This device must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Le présent appareil est conforme aux niveaux limites d'exigences d'exposition RF aux personnes définies par Industrie Canada. L'appareil doit être installé afin d'offir une distance de séparation d'au moins 20cm avec l'utilasateur, et ne doit pas être installé à proximité ou être utilisé en conjonction avec une autre antenne ou un autre émetteur. R&TTE This equipment is in accordance with the requirements of the R&TTE (Radio equipment and telecommunications terminal equipment) directive for the following authorized countries: AT BE BG CH CY CZ DE DK EE ES FI FR GB GR HU IE IS IT LI LT LU LV MT NL PL PT RO SE SI SK TR BA GE HR MD ME MK RS. The R&TTE declaration of conformity is available at www.schneider-electric.com. About this manual This manual is intended for use by designers, system builders and maintenance technicians with an understanding of PLC, WAGES, e…

Text truncated - open the document above for the full version.

Schneider Electric Industries SAS Postal address: 38HP3 – 5 Avenue Raymond Chanas 38320 Eybens, France Tel. +33 (0)4 76 82 28 38 www.schneider-electric.com Letter of Agency 24/11/14 TRaC Global Ltd. 100 Frobisher Business Park Malvern Worcestershire WR14 1BX UK To Whom It May Concern: We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse ACT of 1988, U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002(b), to the application, is subject to denial of federal benefits, that includes FCC benefits. Thank you for your attention to this matter. Yours faithfully Schneider Electric Industries SAS 15/12/2014 X Michael Falconet Project Design Lead

Schneider Electric Industries SAS Postal address: 38HP3 – 5 Avenue Raymond Chanas 38320 Eybens, France Tel. +33 (0)4 76 82 28 38 www.schneider-electric.com DECLARATION OF SIMILARITY Date 03/02/15 TRaC GLOBAL LTD. 100 Frobisher Business Park Malvern Worcestershire WR14 1BX UK RE: Declaration of Similarity FCC ID: 2ADGA-WT4100 IC ID: 12449A-WT4100 To Whom It May Concern: Please be advised that for the models WT4111, WT4112, WT4132, WT4122, WT4141 all RF measurements and test results are exactly the same. The differences between the models are in the data format and sensors used. Thank you for your attention to this matter. Yours faithfully Schneider-Electric SAS 03/02/2015 X Michael Falconet Project Design Lead ModelDescriptionPCBA BOMPCBsFrequencyExternal CableExt. Cable GlandSensorsPCB ModificationsPCB Changes WT4111Single Pulse TxBP-485-0002T/RT0485-USA153.1025MHz4-Core WirePlastic GlandNoneNone WT4112Dual Pulse TxBP-485-0002T/RT0485-USA153.1025MHz4-Core WirePlastic GlandNoneNone WT4132Alarm Status TxBP-485-0002T/RT0485-USA153.1025MHz4-Core WirePlastic GlandNoneNone WT4141Internal Temperature TxBP-485-0002T/RT0485-USA153.1025MHzNoneNoneDallas Temp ICInput Re-ConfiguredResistor/links added WT4122Dual 0-10V Analogue TxBP-485-0002T/RT0485-USA153.1025MHz4-Core WirePlastic GlandNoneInput Re-ConfiguredResistor/Capacitor/links added This is a tabulated form of the hardware differences from the original EcoChirp Pulse transmitter already approved.

Schneider Electric Industries SAS Postal address: 38HP3 – 5 Avenue Raymond Chanas 38320 Eybens, France Tel. +33 (0)4 76 82 28 38 www.schneider-electric.com REQUEST FOR CONFIDENTIALITY IN ACCORDANCE WITH FCC RULE 0.459 03/02/15 TRaC GLOBAL LTD. 100 Frobisher Business Park Malvern Worcestershire WR14 1BX UK RE: Certification Application FCC ID: 2ADGA-WT4100 To Whom It May Concern: Please be advised that the following information is to be held confidential on behalf of Schneider-Electric Industries SAS.  Operation Description  PCBA Bill of Materials  General Assembly Bill of Materials The application contains technical information which Schneider-Electric Industries SAS deems to be trade secrets and propriety. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter. Yours faithfully Schneider Electric Industries SAS 03/02/2015 X Michael Falconet Project Design Lead Block Diagram Schematics l

Pulse Transmitter with Flying Lead Pulse Transmitter with Flying Lead Product Label Internal Temperature Transmitter Product Label

Date: By: Rev Description: All information contained herein is the property of: Halma Water Management, Ty- Coch House, Llantarnum Park Way, Cwmbran, Gwent, NP44 3AW and shall not be copied or transmitted without the prior consent of Palmer Environmental Ltd. Halma Water Management TEL: 01633 489479 FAX: 01633 877857 Approved: Checked: Drawn: Date: Scale: NTS 20/04/2015 OS SJF Title: Dwg. No: Rev: Schneider Electric FCC Label (Page 1 of 1) B LAB-485-0046 OJ Labels for use with FCC approved Schneider Electric transmitters only. 30/04/2015 OS A Initial Release 08/05/2015 OS B Add Product Labels LABEL 1 (Product Label) Label Dimensions:- 1.25 inch x 2 inch HWM Blank Label Stock Part Number:- “ LAB001100 " LABEL 2 (FCC Label) Label Dimensions:- 40mm x 16mm HWM Blank Label Stock Part Number:- “ LAB4022 " WT4111 WT4112 WT4132 WT4141 LAB-485-0046-B (Schneider Electric Product and FCC Label)

Pulse Transmitter with Flying Lead Pulse Transmitter with Flying Lead Product Label Internal Temperature Transmitter Product Label

Generic Transmitter PCB 153.1025MHz

RADIO TEST REPORT FOR Schneider Electric ON METSEWT4141 & METSEWT4122 DOCUMENT NO. TRA-022263-W-US3 Total number of pages: 47 TRaC Wireless Test Report : TRA-022263-W-US3 Applicant : Schneider Electric Apparatus : METSEWT4141 & METSEWT4122 VHF Specification(s) : CFR47 Part 90.217 Purpose of Test : Certification FCCID : 2ADGA-WT4100 IC Certification Number : 12449A-WT4100 Authorised by : : Radio Product Manager Issue Date : 22 July 2015 Authorised Copy Number : PDF TRaC Global Test Report: TRA-022263-W-US3 3 Contents Section 1: Introduction 4 1.1 General 4 1.2 Tests Requested By 5 1.3 Manufacturer 5 1.4 Apparatus Assessed 5 1.5 Test Result Summary 6 1.6 Notes Relating To The Assessment 7 1.7 Deviations from Test Standards 7 Section 2: Measurement Uncertainty 8 2.1 Measurement Uncertainty Values 8 Section 3: Modifications 9 3.1 Modifications Performed During Assessment 9 Section 4 General Test Procedures 10 4.1 Radiated Test Setup and Procedures 10 4.2 AC Powerline Conducted Emissions Test Setup and Procedures 11 4.3 Antenna Port Conducted Emissions 11 4.4 Power Supply Variation 12 4.5 Thermal Variation 12 4.6 Time Domain Measurements 12 Appendix A: Formal Emission Test Results 13 A1 Maximum Radiated Output Power (Effective Radiated Power) 14 A2 Radiated Transmitter Spurious Emissions 18 Appendix B: Supporting Graphical Data 23 Appendix C: Additional Test and Sample Details 30 Appendix D: Additional Information 36 Appendix E: Photographs and Figures 37 Appendix F: FCC To Industry Canada Comparison 46 TRaC Global Test Report: TRA-022263-W-US3 4 Section 1: Introduction 1.1 General This report contains an assessment of an apparatus against Electromagnetic Compatibility Standards based upon tests carried out on samples submitted to the Laboratory. Test performed by: TRaC Global [X] Unit E South Orbital Trading Park Hedon Road Hull, HU9 1NJ. United Kingdom. Telephone: +44 (0) 1482 801801 Fax: +44 (0) 1482 801806 TRaC Global [ ] Unit 1 Pendle Place Skelmersdale West Lancashire, WN8 9PN United Kingdom Telephone: +44 (0) 1695 556666 Fax: +44 (0) 1695 577077 Email: [email protected] Web site: http://www.tracglobal.com Tests performed by: K J Anderson Report author: K J Anderson This report must not be reproduced except in full without prior written permission from TRaC Global. TRaC Global Test Report: TRA-022263-W-US3 5 1.2 Tests Requested By This testing in this report was requested by : Schneider Electric 5 Avenue Raymond Chanas 38320 Eybens France 1.3 Manufacturer HWM Ty Coch House Llantarnam Industrial Park Cwmbran NP44 3AW United Kingdom 1.4 Apparatus Assessed The following apparatus was assessed between the 22/08/14 and 9/10/14: METSEWT4141 VHF The METSEWT4141 VHF series of devices counts pulses from any pulsed output including electricity, water and gas meters. Once installed, the METSEWT4141 will transmit consumption data as well as tamper and battery information via radio at regular intervals. The apparatus is designed to transmit at 153.1 MHz with a carrier power below 120 mW to allow exemption from the full 47CFR Part 90 technical requirements. Testing was performed on four separate examples of the product range containing identical radio modules and as such having Identical FCC ID numbers. Testing was limited to Maximum Radiated Carrier Power and Transmitter Spurious Emissions Radiated to support an application for a Class II permissive change. TRaC Global Test Report: TRA-022263-W-US3 6 1.5 Test Result Summary Full details of test results are contained within Appendix A. The following table summarises the results of the assessment. The statements relating to compliance with the standards below apply ONLY as qualified in the notes and deviations stated in sections 1.6 to 1.7 of this test report. Full details of test results are contained within Appendix A. The following table summarises the results of the assessment. Test Type Regulation Measurement standard Result Maximum Radiated Output Power Title 47 of the CFR: Part 90.217 ASNI/TIA-603-C- 2004 Pass Transmitter Spurious Emissions Radiated Title 47 of the CFR: Part 2.1051 ASNI/TIA-603-C- 2004 Pass Abbreviations used in the above table: ANSI C 63.10:2009 and ASNI/TIA-603-C-2004 is outside the scope of the laboratories UKAS accreditation. CFR : Code of Federal Regulations ANSI : American National Standards Institution REFE : Radiated Electric Field Emissions PLCE : Power Line Conducted Emissions TRaC Global Test Report: TRA-022263-W-US3 7 1.6 Notes Relating To The Assessment With regard to this assessment, the following points should be noted: The results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. The apparatus was set up and exercised using the configurations, modes of operation and arrangements defined in this report only. Particular operating modes, apparatus monitoring methods and performance criteria required by the standards tested to have been performed except where identified in Section 1.7 of this test report (Deviations from Test Standards). For emissions testing, throughout this test report, “Pass” indicates that the results for the sample as tested were below the specified limit (refer also to Section 2, Measurement Uncertainty). Where relevant, the apparatus was only assessed using the monitoring methods and susceptibility criteria defined in this report. All testing was performed under the following environmental conditions: Temperature : 17 to 23 °C Humidity : 45 to 75 % Barometric Pressure : 86 to 106 kPa All dates used in this report are in the format dd/mm/yy. This assessment has been performed in accordance with the requirements of ISO/IEC 17025. 1.7 Deviations from Test Standards Testing was limited to Maximum Radiated Carrier Power and Transmitter Spurious Emissions Radiated to support an application for a Class II permissive change. TRaC Global Test Report: TRA-022263-W-US3 8 Section 2…

Text truncated - open the document above for the full version.

TRaC Global Test Report: TRA-022263-W-US3 37 Appendix E: Photographs and Figures The following photographs were taken of the test samples: 1. Radiated electric field emissions: Front view S15. 2. Radiated electric field emissions: Rear view S15. 3. Radiated electric field emissions: Front view S18. 4. Radiated electric field emissions: Rear view S18. 5. Radiated electric field emissions: Front view S58. 6. Radiated electric field emissions: Rear view S58. 7. Radiated electric field emissions: Front view S59. 8. Radiated electric field emissions: Rear view S59. TRaC Global Test Report: TRA-022263-W-US3 38 Photograph 1 TRaC Global Test Report: TRA-022263-W-US3 39 Photograph 2 TRaC Global Test Report: TRA-022263-W-US3 40 Photograph 3 TRaC Global Test Report: TRA-022263-W-US3 41 Photograph 4 TRaC Global Test Report: TRA-022263-W-US3 42 Photograph 5 TRaC Global Test Report: TRA-022263-W-US3 43 Photograph 6 TRaC Global Test Report: TRA-022263-W-US3 44 Photograph 7 TRaC Global Test Report: TRA-022263-W-US3 45 Photograph 8