2ADM5-EP-0617-LBT TWS SPORT AST

Thank you for purchasing the React True Wireless Earbuds. This manual provides more information about the wireless earbuds, please read the instructions before using. INSTRUCTION MANUAL Product Overview Package Contents 1 2 3 4 5 1. LED Indicator 2. On/Off Button/ Play/Pause Music Answer/End Call 3. On/Off Button 4. LED Indicator 5. Micro USB Charging Port USB PlugMicro USB Plug React True Wireless Earbuds x 1 pair Portable Charging Stand x 1 Micro USB Charging Cable x 1 Instruction Manual x 1 Specifications Driver Diameter: 10 mm Impedance: 32 Ohms Frequency Response: 20 Hz – 20 KHz Sensitivity: 96 ± 3dB Power Supply: Li-ion Battery 3.7V 70 mAh (per Earbud) Li-ion Battery 3.7V 500 mAh (Charging Stand) Play Time: Total 12 Hours (Earbuds playing time is 3 Hours and the Charging Stand can provide 3 times for the earbuds charging) Charging Time: 2-2.5 Hours Bluetooth Range: 32.8 Feet Micro USB cable included Instruction Manual Micro USB Charging Cable Instruction Manual Keep all relevant information for future reference Distributed by 1616 Holdings, Inc. 701 Market Street, Suite 200 Philadelphia, PA 19106 Made in China ITEM# EP-0617 REACT EarbudsCharging Stand Front Back Pair the wireless earbuds with your mobile device 1. Keep the distance between the earbuds and mobile device within 32.8 feet. 2. De-activate the Bluetooth function on your mobile device. 3. Power on both earbuds simultaneously by pressing the On/Off buttons for 3 seconds and wait for 3 to 5 seconds for auto pairing. The Left earbud has indicator blinking alternatively in Red and Blue. The Right earbud will blinking in Blue slowly when auto pairing is successfully on L/R earbuds. 4. Activate the Bluetooth function on your mobile device and select “REACT TWS” from the list shown. 5. After pairing successfully, both earbuds will start blinking slowly in blue. *Attention: If the auto pairing is not successful, manual pairing between earbuds is essential by following below procedures: 1. Make sure the earbuds are charged. 2. De-activate the Bluetooth function on your mobile device. (if you had been paired the earbuds to some other mobile device(s) nearby, please sure to de-activate those device(s) too). 3. Power on both earbuds simultaneously by pressing the On/Off buttons for 3 seconds and wait for 3 to 5 seconds for auto pairing. (Keep the Bluetooth function off on your mobile device before this operation.) 4. Activate the Bluetooth function on your mobile device and select “REACT TWS” from the list shown. 5. After pairing successfully, both earbuds will start blinking slowly in blue. Reconnect the wireless earbuds to your mobile device Disconnect the wireless earbuds from your mobile device Power off the wireless earbuds; or Switch off the Bluetooth on your mobile phone; or Leave the earbuds 60ft away from your mobile phone or further. Power On/Off Power On Press and hold down the On/Off Button of earbuds for 3 seconds and the LED will flash. Power Off Press and hold down the On/Off Button of earbuds for 4 seconds and the LED will turn off. When powered on, the wireless earbuds will automatically connect with the last successfully paired device. Answer / Reject a call When receive a call, press the On/Off Button once ( on either earbud) to accept the call, or answer the call normally via your moblie phone. Press and hold 2 seconds to reject it. NOTE: • You must select a qualified charger from a regular manufacturer. • You must charge the charging stand and earbuds if it has been not used for more than 12 months. End a call To end the call, just press On/Off button at any side of earbud with Beep sound to end it. Functions Pause / Play Music: Short Press on On/OFF Button Go back to previous song: Press Left On/Off Button for 1 second. Advance to next song: Press Right On/Off Button for 1 second. Volume Up: Double click Right On/Off button to increase. Volume Down:Double click Left On/Off button to reduce. 1. Use the Micro USB charging cable provided with the packaging. 2. Connect the Micro USB plug to Micro USB charging port on the charging stand, then connect the USB plug to a USB port on a computer or wall adapter to begin charging. 3. The Red LED on the charging stand will be on blink during charge. 4. Once fully charged, the Red LED will be off. Recharge Charging Stand 1. Insert the React Earbuds on the charging stand. 2. Press the On/Off button on the stand, charging will be started. 3. LED indicator light of the charging stand will be turned Blue when charging your earbuds. 4. Once fully charged, the LED will be off. Charging your Earbuds If the wireless earbuds cannot be paired with your device, please try the following: Ensure that your earbuds are in pairing mode or reconnection mode Ensure that Bluetooth search function of your mobile device is activated. If the wireless earbuds will not turn on: Make sure the earbuds are fully charged. Can I change the battery for the earbuds? The wireless earbuds use a built-in non-detachable battery which cannot be removed. If the Portable charge stand cannot be recharged: If you use a power outlet, ensure that the power supply is connected securely and the outlet works. If you use a computer, ensure that it is connected and the USB port is powered. FAQ -The input voltage to the product is 5V 1A. -In order to charge the product in safe manner and reliable conditions, please only adopt certified appropriate charger/ adapter for charging the product. -Only charge the product at ambient temperatures between 10 deg °C/ 50 deg °F and 40 deg °C/104 deg °F. - Do not heat above 70 deg °C/158 deg °F, eg. Do not expose to sunlight or throw into fire. -Switch off the product after use. -Please note that we won’t take any responsibility for any wrong operation (eg. Voltage higher than 5V) as this may result in severe injury or loss of property, and we cannot control the operating process during the time the user using this product. -In extreme cases, abuse or misuse of Lithium battery pack c…

Text truncated - open the document above for the full version.

Zeeva International Limited Suite 1007B, 10th Floor, Exchange Tower, 33 Wang Chiu Road,Kowloon Bay, Hong Kong Tel: +852-2868 0511 | Fax: +852-2524 1986 E-mail: [email protected] Date: 05/15/2020 To: FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 We, Zeeva International Limited hereby declare that： Product Name: BT TWS SPORT AST Model No: EP-0617 FCC ID: 2ADM5-EP-0617-L For BT Mode: BLE are disable by software For Below are activated: Bluetooth BDR(GFSK) , EDR(π/4‐DQPSK), EDR(8DPSK) Except for the manufacturer, the end user does not have any capability to modify/change the RF parameters. We acknowledge that it is the manufacturer’s responsibility to provide the radio configurations to ensure compliance with Commission’s rules. Sincerely Yours, Signature: Printed Name: Akshay P Butani Tiltle: Vice President

Antenna Battery 26M crystal oscillator power amplifier 2402-2480MHz A

Zeeva International Limited Suite 1007B, 10th Floor, Exchange Tower, 33 Wang Chiu Road, Kowloon Bay, Hong Kong Tel: +852-2868 0511 | Fax: +852-2524 1986 E-mail: [email protected] FCC Authorization 04/24/2020 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We, Zeeva International Limited the undersigned, hereby authorize Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratory Corporation on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature: Printed Name: Akshay P Butani Title: Vice President QA-FR-170-B

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS Charging box

EXHIBIT A - FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS BT Antenna Charging box

26MHz AB5337 Circuit Description 1. Battery(3.7V)provides energy for the Bluetooth chip( A) ;Crystal oscillator() provides the clock signal for the Bluetooth chip. Bluetooth signals get through a matching circuit, and then transmitted to the space through the antenna（2402MHz‐2480MHz）. When the product is connected, the product can be in two‐way communication with other Bluetooth devices, and then the device's Bluetooth module sends Bluetooth signals into space, the product receives the Bluetooth signal through an antenna, transmission to the Bluetooth chip via matching circuit.

Note: This report must not be used by the customer to claim product certification, approval, or endorsement by A2LA* or any agency of the Federal Government. This report may contain data that are not covered by the A2LA accreditation and are marked with an asterisk “★”. BACL is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with an asterisk ’*’. Customer model name, addresses, names, trademarks etc. are not considered data. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. FCC PART 15.247 TEST REPORT For Zeeva International Limited Suite 1007B, 10th Floor, Exchange Tower 33 Wang Chiu Road, Kowloon Bay, HongKong, China FCC ID: 2ADM5-EP-0617-L Report Type: Original Report Product Type: BT TWS SPORT AST Re port Number: RSZ200323831-00 Re port Date: 2020-04-24 Reviewed B y: Jimmy Xiao RF En gineer Prepared By: Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F., West Wing, Third Phase of Wanli Industrial Building, Shihua Road, Futian Free Trade Zone, Shenzhen, Guangdong, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ200323831-00 FCC Part 15.247 Page 2 of 29 TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 4 OBJECTIVE ................................................................................................................................................................... 4 RELATED SUBMITTAL(S)/GRANT(S) ............................................................................................................................. 4 TEST METHODOLOGY .................................................................................................................................................. 4 MEASUREMENT UNCERTAINTY .................................................................................................................................... 5 TEST FACILITY ............................................................................................................................................................. 5 SYSTEM TEST CONFIGURATION .......................................................................................................................... 6 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 6 EUT EXERCISE SOFTWARE .......................................................................................................................................... 6 SPECIAL ACCESSORIES ................................................................................................................................................. 6 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 6 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 6 EXTERNAL I/O CABLE .................................................................................................................................................. 6 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 7 SUMMARY OF TEST RESULTS ............................................................................................................................... 8 TEST EQUIPMENT LIST ........................................................................................................................................... 9 FCC§15.247 (i), §1.1307 (b) (1) &§2.1093 – RF EXPOSURE ...................................................................................... 10 APPLICABLE STANDARD ............................................................................................................................................ 10 FCC §15.203 – ANTENNA REQUIREMENT .......................................................................................................... 11 APPLICABLE STANDARD ............................................................................................................................................ 11 ANTENNA CONNECTOR CONSTRUCTION .................................................................................................................... 11 FCC §15.207 (a) – AC LINE CONDUCTED EMISSIONS ..................................................................................... 12 APPLICABLE STANDARD ............................................................................................................................................ 12 EUT SETUP ................................................................................................................................................................ 12 EMI TEST RECEIVER SETUP ....................................................................................................................................... 12 TEST PROCEDURE ...................................................................................................................................................... 12 CORRECTED FACTOR & MARGIN CALCULATION ......................................................................................…

Text truncated - open the document above for the full version.

Appendix A: 20dB Emission Bandwidth Test Result TestMode Antenna Channel 20db EBW[MHz] Limit[MHz] Verdict DH1 Ant1 2402 0.930 --- PASS 2441 0.930 --- PASS 2480 0.951 --- PASS 2DH1 Ant1 2402 1.248 --- PASS 2441 1.254 --- PASS 2480 1.257 --- PASS 3DH1 Ant1 2402 1.242 --- PASS 2441 1.254 --- PASS 2480 1.260 --- PASS Test Graphs DH1_Ant1_2402 DH1_Ant1_2441 DH1_Ant1_2480 2DH1_Ant1_2402 2DH1_Ant1_2441 2DH1_Ant1_2480 3DH1_Ant1_2402 3DH1_Ant1_2441 3DH1_Ant1_2480 Appendix B: Maximum conducted Peak output power Test Result Test Mode Antenna Channel Result[dBm] Limit[dBm] Verdict DH1 Ant1 2402 -8.09 <=20.97 PASS 2441 -9.29 <=20.97 PASS 2480 -11.06 <=20.97 PASS 2DH1 Ant1 2402 -7.57 <=20.97 PASS 2441 -9.8 <=20.97 PASS 2480 -10.7 <=20.97 PASS 3DH1 Ant1 2402 -7.19 <=20.97 PASS 2441 -9.47 <=20.97 PASS 2480 -10.47 <=20.97 PASS Appendix C: Carrier frequency separation Test Result TestMode Antenna Channel Result[MHz] Limit[MHz] Verdict DH1 Ant1 Hop 1.003 >=0.620 PASS 2DH1 Ant1 Hop 1.000 >=0.832 PASS 3DH1 Ant1 Hop 1.139 >=0.828 PASS Test Graphs DH1_Ant1_Hop 2DH1_Ant1_Hop 3DH1_Ant1_Hop Appendix D: Time of occupancy Test Result Test Mode AntennaChannel Burst Width [ms] Total Hops [Num] Result[s]Limit[s] Verdict DH1 Ant1 Hop 0.38 320 0.120 <=0.4 PASS DH3 Ant1 Hop 1.62 120 0.195 <=0.4 PASS DH5 Ant1 Hop 2.86 80 0.229 <=0.4 PASS 2DH1 Ant1 Hop 0.38 320 0.122 <=0.4 PASS 2DH3 Ant1 Hop 1.63 90 0.146 <=0.4 PASS 2DH5 Ant1 Hop 2.87 90 0.258 <=0.4 PASS 3DH1 Ant1 Hop 0.38 320 0.122 <=0.4 PASS 3DH3 Ant1 Hop 1.63 90 0.146 <=0.4 PASS 3DH5 Ant1 Hop 2.87 60 0.172 <=0.4 PASS Note 1: A period time=0.4*79=31.6(S), Result= Burst Width* Total Hops Note 2: Total Hops=Hopping Number in 3.16s*10 Note 3: Hopping Number in 3.16s=Total of highest signals in 3.16s (Second high signals were other channel) Test Graphs DH1_Ant1_Hop DH3_Ant1_Hop DH5_Ant1_Hop 2DH1_Ant1_Hop 2DH3_Ant1_Hop 2DH5_Ant1_Hop 3DH1_Ant1_Hop 3DH3_Ant1_Hop 3DH5_Ant1_Hop Appendix E: Number of hopping channels Test Result TestMode Antenna Channel Result[Num] Limit[Num] Verdict DH1 Ant1 Hop 79 >=15 PASS 2DH1 Ant1 Hop 79 >=15 PASS 3DH1 Ant1 Hop 79 >=15 PASS Test Graphs DH1_Ant1_Hop 2DH1_Ant1_Hop 3DH1_Ant1_Hop Appendix F:Band edge measurements Test Graphs DH1_Ant1_Low_2402 DH1_Ant1_High_2480 DH1_Ant1_Low_Hop_2402 DH1_Ant1_High_Hop_2480 2DH1_Ant1_Low_2402 2DH1_Ant1_High_2480 2DH1_Ant1_Low_Hop_2402 2DH1_Ant1_High_Hop_2480 3DH1_Ant1_Low_2402 3DH1_Ant1_High_2480 3DH1_Ant1_Low_Hop_2402 3DH1_Ant1_High_Hop_2480

EXHIBIT D - TEST SETUP PHOTOGRAPHS Conducted Emissions - Front View Conducted Emissions - Side View Radiated Emissions View (Below 1 GHz) Radiated Emissions View (Above 1 GHz)