2ADPDGT1216WIFI IOE Module

GT1216 OEM Installation Manual V1.0 Shenzhen Longsys Electronics Co.,Ltd www.Longsys.com 8/F, 1 Building. Finance Base, NO.8, KeFa Road, Shenzhen, China Tel: 86-755-86168848 10/F, CHINA AEROSPACE CENTRE,143 HOI BUN ROAD, HK Tel: 852-23850111 GT1216 OEM Installation Manual Version 1.0 Nov . 2014 GT1216 OEM Installation Manual V1.0 Shenzhen Longsys Electronics Co.,Ltd www.Longsys.com 8/F, 1 Building. Finance Base, NO.8, KeFa Road, Shenzhen, China Tel: 86-755-86168848 10/F, CHINA AEROSPACE CENTRE,143 HOI BUN ROAD, HK Tel: 852-23850111 1. The RF module limited to OEM installation ONLY. •The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified •RF module is integrated. 2. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 3. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. •This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - l Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - l Consult the dealer or an experienced radio/TV technician for help. •FCC Caution •Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or ransmitter. •FCC RF Exposure requirements •This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. • This device is intended only for OEM integrators under the following conditions: •The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. GT1216 OEM Installation Manual V1.0 Shenzhen Longsys Electronics Co.,Ltd www.Longsys.com 8/F, 1 Building. Finance Base, NO.8, KeFa Road, Shenzhen, China Tel: 86-755-86168848 10/F, CHINA AEROSPACE CENTRE,143 HOI BUN ROAD, HK Tel: 852-23850111 •IMPORTANT NOTE: •In the event that these conditions cannot be met (for example certain laptop configurations or colocation with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. •End Product Labeling •This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: 2ADF6GT1216”. •The grantee's FCC ID can be used only when all FCC/ IC compliance requirements are met. •Manual Information To the End User •The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. •The end user manual shall include all required regulatory information/warning as show in this manual. •Operations in 2.412-2.472GHz band are for indoor use only. The module is limited to mobile installations There is a requirement that the grantee provide guidance to the host manufacturer for compliance with Part 15B requirements. GT1216 OEM Installation Manual V1.0 Shenzhen Longsys Electronics Co.,Ltd www.Longsys.com 8/F, 1 Building. Finance Base, NO.8, KeFa Road, Shenzhen, China Tel: 86-755-86168848 10/F, CHINA AEROSPACE CENTRE,143 HOI BUN ROAD, HK Tel: 852-23850111 Features： Wireless Specification Standard supported: IEEE802.11b/g/n Frequency: 2.412 to 2.484GHz Channels: up to 13 channels Performance Specification Host data rates UART: 115200bps, 8, n, 1 SPI: up to 12 Mbps Link rates up to 150MHz Protocols Internet protocols: IPv4/IPv6, TCP/UDP, ARP/NDP, DHCPv4, ICMPv6 Security protocols: WPS, WPA, WPA2, WAPI, WEP, TKIP Typical application Household appliances Gaming consoles Handheld terminals Embedded wireless products security monitoring device industrial remote control Home automation The GT1216 module contains a Qualcomm® QCA4004 chip. The QCA4004 is a single chip system on a chip (SoC) 1x1 802.11 b/g/n device optimized for low-power embedded applications with single-stream capability for both Tx and Rx. The QCA4004 includes a TCP/IP and UDP offload capability. This capability can reduce Flash requirements on a host MCU by up to 100 KBytes and also free up CPU cycles. The IP stack is a simultaneous IPv4/IPv6 stack with a BSD-like interface t…

Text truncated - open the document above for the full version.

2ADPDGT1216 LONGSYS ELECTRONICS (HK) CO.,LIMITEDONGSYS ELECTRONICS (HK) CO.,LIMITED LONGSYS ELECTRONICS (HK) CO.,LIMITED

1 Photographs - EUT Constructional Details

SIZE: 14mm X 16.5mm R=0.5mm 公差为正负0.1mm 材质：聚酰哑胺，白底黑字，单色印刷 DATE:06/11/2014DESIGNER: © Copyright Shenzhen Netcom Electronics Co.,Ltd 2014 | netcom STICKER Part No: longsys Junxia Zhang CHECK: Junxia Zhang GEB06001B 16.5mm 14.0mm 9.7mm 10.7mm 6.0mm 6.0mm 1.6mm WIFI IOE Module GT1216 MAC:XXXXXXXXXXXX FCC ID2ADPDGT1216

1 Photographs - EUT Constructional Details

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM141000562302 Page: 1 of 7 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page RF Exposure Evaluation Report Application No: SZEM1410005623CR Applicant: LONGSYS ELECTRONICS (HK) CO.,LIMITED Manufacturer/Factory: LONGSYS ELECTRONICS (HK) CO.,LIMITED Product Name: WIFI IOE Module Model No.(EUT): GT1216 FCC ID: 2ADPDGT1216 Standards: 47 CFR Part 1.1307(2013) 47 CFR Part 1.1310(2013) Date of Receipt: 2014-10-14 Date of Test: 2014-10-29 to 2014-11-17 Date of Issue: 2014-11-20 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM141000562302 Page: 2 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2014-11-20 Original Authorized for issue by: Tested By 2014-11-17 (Jim Huang) /Project Engineer Date Prepared By 2014-11-20 (Sade Luo) /Clerk Date Checked By 2014-11-24 (Emen Li) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM141000562302 Page: 3 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Contents Page 1 COVER PAGE .......................................................................................................................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Ltd. No. 1 Workshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM141000562301 Page: 1 of 117 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page FCC REPORT Application No: SZEM1410005623CR Applicant: LONGSYS ELECTRONICS (HK) CO.,LIMITED Manufacturer/Factory: LONGSYS ELECTRONICS (HK) CO.,LIMITED Product Name: WIFI IOE Module Model No.(EUT): GT1216 FCC ID: 2ADPDGT1216 Standards: 47 CFR Part 15, Subpart C (2013) Date of Receipt: 2014-10-14 Date of Test: 2014-10-29 to 2014-11-17 Date of Issue: 2014-11-20 Test Result: PASS * . * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM141000562301 Page: 2 of 117 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2014-11-20 Original Authorized for issue by: Tested By 2014-11-17 (Jim Huang) /Project Engineer Date Prepared By 2014-11-20 (Sade Luo) /Clerk Date Checked By 2014-11-24 (Emen Li) /Reviewer Date SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM141000562301 Page: 3 of 117 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Test Summary Test Item Test Requirement Test method Result Antenna Requirement 47 CFR Part 15, Subpart C Section 15.203/15.247 (c) ANSI C63.10 2009 PASS AC Power Line Conducted Emission 47 CFR Part 15, Subp…

Text truncated - open the document above for the full version.

1 Photographs - EUT Test Setup Test model No.: GT1216 1.1 Radiated Spurious Emission 1.2 Conducted Emission