2ADSOAM08S2.4G Transmitting Box

（Apex Toys) 2 Manaual The important parameters： 1，2.4G Remote control distance is more than 30 meters 2，Pull the transmitter out and enter the sleep time: 10 seconds. 3，Usage duration: more than 10 hours 4，Static Battery when it sleep: below 0.1mA FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. （Apex Toys) 3 Block diagram Product Features: This product can be connected with the mobile phone to control the toy plane Product main components： 80MAH li-polymer battery Master MCU, with a sleep function 3.5 mm plug Audio signal 2.4G Transmitting module Power Light Charge system （Apex Toys) 4 1. The upper body of transmitter 2. The red light 3. The bottom body of transmitter 4. Charger hole 5. 3.5mm Audio plug 6. PCBA 8. 2.4G transmitting module 7. Master MCU （Apex Toys) 5 2.4G Audio transmitter function light description： NO. Name Material Color Requirements 1 The upper body of transmitter 30%PC+ABS Black/White Injection& Sink printing 2 Power light Red Soft and Not dazzling 3 The bottom body of transmitter 30%PC+ABS Black/White Injection& Sink printing 4 Charger hole Black DC Seat 5 3.5mm audio plug Nickel-plated Standard mobile phones with 3.5mm four plug section 6 PCBA FR-4 White word & Green oil HAL 7 Master MCU Black 8 2.4G transmitting module White word & Green oil HAL 9 Battery 80MAH li-polymer battery 10 Antenna Copper White 11 Transparent hold LED ABS Transparent 9. Battery 11. Transparent hold LED 10. Antenna （Apex Toys) 6 The internal assembly structure： Function Description Function light Color Functioning Pattern The status of the lamp Successful connection on the phone Flashing slowly, 1/second 2.4G connected successfully Often Bright state Sleep Light off Indicator Light Red No connected Light off The internal assembly structure （Apex Toys) 7 The upper body of transmitter The bottom body of transmitter （Apex Toys) 8 2.4G Audio transmitter matching process： Switch on the Helicopter The LED lamp is flashing. To insert the 2.4 audio transmitter into mobile phone Enter the corresponding control software Push the ON/OFF on the software to the ON file, Then the 2.4G audio transmitter will paired with Aircraft automatically. The pairing is successful, the LED light on the 2.4G transmitter will light up, and the LED light on the plan also will light up. Operation in the user interface, Then you can control the toys.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (current) 4.0 5.0 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0 Apex Toys (Shenzhen)Co., Ltd. A. Floor 4, A001 Building, Zhi Ji Industrial Park, No.92 KuiChong Street, LongGang District, ShenZhen, China 2014-12-11 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, Apex Toys (Shenzhen)Co., Ltd. hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): FCC ID: 2ADSOAM08S Model: AM08S Product name: 2.4G Transmitting Box Sincerely, signature : name / title: Amy Zhang / Manager address: A. Floor 4, A001 Building, Zhi Ji Industrial Park, No.92 KuiChong Street, LongGang District, ShenZhen, China

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 Apex Toys (Shenzhen)Co., Ltd. A. Floor 4, A001 Building, Zhi Ji Industrial Park, No.92 KuiChong Street, LongGang District, ShenZhen, China 2014-12-11 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2ADSOAM08S We hereby request confidential treatment of information accompanying this application as outlined below: Block Diagram Schematics Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, signature : name / title: Amy Zhang / Manager address: A. Floor 4, A001 Building, Zhi Ji Industrial Park, No.92 KuiChong Street, LongGang District, ShenZhen, China

Label location Model No.: AM08S FCC ID: 2ADSOAM08S

Antenna location

FCC ID: 2ADSOAM08S Keyway Testing Technology Co., Ltd. Report No. 14KWE122012F Page 1 of 19 FCC TEST REPORT for Apex Toys (Shenzhen)Co., Ltd. 2.4G Transmitting Box Model Number: AM08S FCC ID: 2ADSOAM08S Prepared for : Apex Toys (Shenzhen)Co., Ltd. Address : 4th Floor, B7 Building, Xujinchang Industry Park, Haoye Road, Fuyong Town, Baoan District, Shenzhen City, China. Prepared by : Keyway Testing Technology Co., Ltd. Address : Building 1, Baishun Industrial Zone, Zhangmotou Town, Dongguan, Guangdong, China Tel: 86-769-8718 2258 Fax: 86-769-8718 1058 Report No. : 14KWE122012F Date of Test : Dec. 7~10, 2014 Date of Report : Dec. 11, 2014 FCC ID: 2ADSOAM08S Keyway Testing Technology Co., Ltd. Report No. 14KWE122012F Page 2 of 19 TABLE OF CONTENTS Declaration Page 1. TEST SUMMARY .......................................................................................................................... 4 2. GENERAL PRODUCT INFORMATION......................................................................................... 4 2.1. Product Function.................................................................................................................... 4 2.2. Description of Device (EUT) .................................................................................................. 4 2.3. Difference between Model Numbers...................................................................................... 4 2.4. Independent Operation Modes .............................................................................................. 4 2.5. Test Supporting System......................................................................................................... 4 3. TEST SITES .................................................................................................................................. 5 3.1. Test Facilities ......................................................................................................................... 5 3.2. List of Test and Measurement Instruments............................................................................ 6 4. TEST SET-UP AND OPERATION MODES .................................................................................. 7 4.1. Principle of Configuration Selection .......................................................................................7 4.2. Block Diagram of Test Set-up ................................................................................................ 7 4.3. Test Operation Mode and Test Software ............................................................................... 7 4.4. Special Accessories and Auxiliary Equipment ....................................................................... 7 4.5. Countermeasures to Achieve EMC Compliance.................................................................... 7 5. EMISSION TEST RESULTS ......................................................................................................... 8 5.1. Radiated Emission Test ......................................................................................................... 8 6. 20DB OCCUPY BANDWIDTH..................................................................................................... 14 6.1. Limits.................................................................................................................................... 14 6.2. Test setup ............................................................................................................................ 14 7. BAND EDGE COMPLIANCE TEST............................................................................................. 16 7.1. Limits.................................................................................................................................... 16 7.2. Test setup ............................................................................................................................ 16 8. ANTENNA REQUIREMENTS...................................................................................................... 17 8.1. Limits.................................................................................................................................... 17 8.2. Result................................................................................................................................... 17 9. PHOTOGRAPHS OF TEST SET-UP .......................................................................................... 18 10. PHOTOGRAPHS OF THE EUT............................................................................................... 19 FCC ID: 2ADSOAM08S Keyway Testing Technology Co., Ltd. Report No. 14KWE122012F Page 3 of 19 Keyway Testing Technology Co., Ltd. Applicant: Address: Apex Toys (Shenzhen)Co., Ltd. 4th Floor, B7 Building, Xujinchang Industry Park, Haoye Road, Fuyong Town, Baoan District, Shenzhen City, China. Manufacturer: Address: Apex Toys (Shenzhen)Co., Ltd. 4th Floor, B7 Building, Xujinchang Industry Park, Haoye Road, Fuyong Town, Baoan District, Shenzhen City, China. E.U.T: 2.4G Transmitting Box Model Number: AM08S Trade Name: Serial No.: ------ Date of Receipt: Dec. 7, 2014 Date of Test: Dec. 7~10, 2014 Test Specification: FCC Part 15, Subpart C Section 15.249: Oct. 1, 2014 ANSI C63.4:2009 Test Result: The equipment under test was found to be compliance with the requirements of the standards applied. Issue Date: Dec. 11, 2014 Tested by: Reviewed by: Approved by: Jack Bu / Engineer Andy Gao / Supervisor Jade Yang/ Supervisor Other Aspects: None. Abbreviations: OK/P=passed fail/F=failed n.a/N=not applicable E.U.T=equipment under tested This test report is based on a single evaluation of one sample of above mentioned products. It is not permitted to be duplicated in extracts without written approval of Keyway Testing Technology Co., Ltd. FCC ID: 2ADSOAM08S Keyway Testing Technology Co., Ltd. Report No. 14KWE122012F Page 4 of 19 1. TEST SUMMARY Test Items …

Text truncated - open the document above for the full version.

Radiated Emission