2ADTA-RFID1233093/3094

Caution: This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.

FCC ID: 2ADTA-RFID123 Page 1 of 2 External Picture FCC ID: 2ADTA-RFID123 Page 2 of 2

label position 3cm 0.7cm 4cm Model:3093/3094 FCC ID:2ADTA-RFID123

FCC ID: 2ADTA-RFID123 Page 1 of 3 Internal Picture FCC ID: 2ADTA-RFID123 Page 2 of 3 FCC ID: 2ADTA-RFID123 Page 3 of 3

FCC ID: 2ADTA-RFID123 TTRFfcc15.249a/effective date: September 15 th , 2009 Page 1 of 18 EMC TEST REPORT for Intentional Radiator No. 141200755SHA-001 Applicant : The Kyjen Company 15514 East Hinsdale Circle,Unit A Centennial,CO 80112 Manufacturer : Jiangsu KSBL TECH CO.,LTD NO,19Tianquan RD.,QILIN IND.,PARK,Jiangning District,Nanjing City Jiangsu Province,CN Product Name : MOVE N SHAKE HEDGEHOG&FROG Type/Model : 3093/3094 SUMMARY The equipment complies with the requirements according to the following standard(s): 47CFR Part 15 (2013): Radio Frequency Devices ANSIC63.4 (2003): American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz Date of issue: Dec 15, 2014 Prepared by: Reviewed by: Jesse Xu (Project Engineer) Daniel Zhao (Reviewer) FCC ID: 2ADTA-RFID123 TTRFfcc15.249a/effective date: September 15 th , 2009 Page 2 of 18 Description of Test Facility Name: Intertek Testing Services Limited Shanghai Address: Building 86, No. 1198 Qinzhou Rd., North, Shanghai 200233, P.R. China FCC Registration Number: 236597 IC Assigned Code: 2042B-1 Name of contact: Jonny Jing Tel: +86 21 61278271 Fax: +86 21 54262353 FCC ID: 2ADTA-RFID123 TTRFfcc15.249a/effective date: September 15 th , 2009 Page 3 of 18 Content SUMMARY .......................................................................................................................................................... 1 DESCRIPTION OF TEST FACILITY ......................................................................................................................... 2 1. GENERAL INFORMATION ............................................................................................................................ 4 1.1 Applicant Information ..................................................................................................... 4 1.2 Identification of the EUT ................................................................................................ 4 1.3 Technical specification ................................................................................................... 5 1.4 Mode of operation during the test / Test peripherals used .............................................. 5 2. TEST SPECIFICATION .................................................................................................................................. 6 2.1 Instrument list ................................................................................................................. 6 2.2 Test Standard .................................................................................................................. 6 3. RADIATED EMISSION ................................................................................................................................... 8 3.1 Test limit ......................................................................................................................... 8 3.2 Test Configuration .......................................................................................................... 8 3.3 Test procedure and test setup .......................................................................................... 9 3.4 Test protocol ................................................................................................................. 10 4. ASSIGNED BANDWIDTH (20DB BANDWIDTH) ............................................................................................ 10 4.1 Limit .............................................................................................................................. 11 4.2 Test Configuration ........................................................................................................ 11 4.3 Test procedure and test setup ........................................................................................ 11 4.4 Test protocol ................................................................................................................. 12 5. POWER LINE CONDUCTED EMISSION ........................................................................................................ 13 5.1 Limit .............................................................................................................................. 13 5.2 Test configuration ......................................................................................................... 13 5.3 Test procedure and test set up ....................................................................................... 14 5.4 Test protocol ................................................................................................................. 15 6. OCCUPIED BANDWIDTH ............................................................................................................................ 16 6.1 Test limit ....................................................................................................................... 16 6.2 Test Configuration ........................................................................................................ 16 6.3 Test procedure and test setup ........................................................................................ 16 6.4 Test protocol ................................................................................................................. 16 7. SPURIOUS EMISSION FOR RECEIVER ......................................................................................................... 17 7.1 Test limit ....................................................................................................................... 17 7.2 Test Configuration ........................................................................................................ 17 7.3 Test procedure and test setup ........................................................................................ 17 7.4 Test protocol .................…

Text truncated - open the document above for the full version.

FCC ID: 2ADTA-RFID123 Page 1 of 2 Test Setup FCC ID: 2ADTA-RFID123 Page 2 of 2 1. Radiated Emission 30MHz-1000MHz Higher than 1GHz