2ADUM-OPL301OPCOM-1

FCC Information and Copyright This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (current) 4.0 5.0 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0 OPCOM O.E.(DONGGUAN) INC. 2015-02-03 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, ___ OPCOM O.E.(DONGGUAN) INC..__ hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): Product： OPCOM-1 Trade Name： OPCOM Link Model Name： OPL301 Serial Model： N/A FCC ID： 2ADUM-OPL301 Sincerely, Signature Name: emmaz Zhu Title: Manager Address: Gu Cun Industry Estate Dajing Countryside Committee Houjie Town,Dongguan City Guangdong,China

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 OPCOM O.E.(DONGGUAN) INC. 2015-02-03 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2ADUM-OPL301 We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Schematics - Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature Signature Name: emmaz Zhu Title: Manager Address: Gu Cun Industry Estate Dajing Countryside Committee Houjie Town,Dongguan City Guangdong,China

APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6 Antenna

FCC ID LABELING AND LOCATION FCC ID Label OPCOM-1 Model NO.: OPL301 FCC ID: 2ADUM-OPL301 FCC ID Label Location The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6 Photo 7 Photo 8 Photo 9 Photo 10 Photo 11

FCC RADIO TEST REPORT-WIFI FCC ID: 2ADUM-OPL301 Product： OPCOM-1 Trade Name： OPCOM Link Model Name： OPL301 Serial Model： N/A Report No.： NTEK-2014NT0620972F Prepared for OPCOM O.E.(DONGGUAN) INC. Gu Cun Industry Estate Dajing Countryside Committee Houjie Town,Dongguan City Guangdong,China Prepared by NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street Bao’an District, Shenzhen P.R. China Tel.: +86-0755-61156588 Fax.: +86-0755-61156599 Website:www.ntek.org.cn Page 2 of 49 Report No.: NTEK-2014NT0620972F TEST RESULT CERTIFICATION Applicant’s name ........ OPCOM O.E.(DONGGUAN) INC. Address ........................ Gu Cun Industry Estate Dajing Countryside Committee Houjie Town,Dongguan City Guangdong,China Manufacture's Name ... OPCOM O.E.(DONGGUAN) INC. Address ........................ Gu Cun Industry Estate Dajing Countryside Committee Houjie Town,Dongguan City Guangdong,China Product description Product name .................OPCOM-1 Model and/or type reference ..................... OPL301 Serial Model .................... N/A Standards .................... FCC Part15.247: 01 Oct. 2014 Test procedure ................ ANSI C63.4-2003 and KDB 558074 : June 5, 2014 This device described above has been tested by NTEK, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of NTEK, this document may be altered or revised by NTEK, personal only, and shall be noted in the revision of the document. Date of Test ...................................... Date (s) of performance of tests ....... 01 Sep. 2014 ~07 Nov. 2014 Date of Issue ..................................... 07 Nov. 2014 Test Result ......................................... Pass Testing Engineer : Denny Huang Technical Manager : (Brown Lu) Authorized Signatory : (Bill Yao) Page 3 of 49 Report No.: NTEK-2014NT0620972F Table of Contents Page 1 . SUMMARY OF TEST RESULTS 5 1.1 TEST FACILITY 6 1.2 MEASUREMENT UNCERTAINTY 6 2 . GENERAL INFORMATION 7 2.1 GENERAL DESCRIPTION OF EUT 7 2.2 DESCRIPTION OF TEST MODES 9 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 10 2.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 11 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 12 3 . EMC EMISSION TEST 13 3.1 CONDUCTED EMISSION MEASUREMENT 13 3.1.1 POWER LINE CONDUCTED EMISSION LIMITS 13 3.1.2 TEST PROCEDURE 14 3.1.3 DEVIATION FROM TEST STANDARD 14 3.1.4 TEST SETUP 14 3.1.5 EUT OPERATING CONDITIONS 14 3.1.6 TEST RESULTS 15 3.2 RADIATED EMISSION MEASUREMENT 17 3.2.1 RADIATED EMISSION LIMITS 17 3.2.2 TEST PROCEDURE 18 3.2.3 DEVIATION FROM TEST STANDARD 18 3.2.4 TEST SETUP 19 3.2.5 EUT OPERATING CONDITIONS 20 3.2.6 TEST RESULTS (BETWEEN 9KHZ – 30 MHZ) 21 3.2.7 TEST RESULTS (BETWEEN 30MHZ – 1GHZ) 22 3.2.8 TEST RESULTS (ABOVE 1000 MHZ) 24 4 . POWER SPECTRAL DENSITY TEST 25 4.1 APPLIED PROCEDURES / LIMIT 25 4.1.1 TEST PROCEDURE 25 4.1.2 DEVIATION FROM STANDARD 25 4.1.3 TEST SETUP 25 4.1.4 EUT OPERATION CONDITIONS 25 4.1.5 TEST RESULTS 26 5 . BANDWIDTH TEST 32 5.1 APPLIED PROCEDURES / LIMIT 32 5.1.1 TEST PROCEDURE 32 Page 4 of 49 Report No.: NTEK-2014NT0620972F Table of Contents Page TEST SETUP 32 5.1.2 EUT OPERATION CONDITIONS 32 5.1.3 TEST RESULTS 33 6 . PEAK OUTPUT POWER TEST 39 6.1 APPLIED PROCEDURES / LIMIT 39 6.1.1 TEST PROCEDURE 39 6.1.2 DEVIATION FROM STANDARD 39 6.1.3 TEST SETUP 39 6.1.4 EUT OPERATION CONDITIONS 39 6.1.5 TEST RESULTS 40 7 . 100 KHZ BANDWIDTH OF FREQUENCY BAND EDGE 41 7.1 DEVIATION FROM STANDARD 41 7.2 TEST SETUP 41 7.3 EUT OPERATION CONDITIONS 41 7.4 TEST RESULTS 42 8 . ANTENNA REQUIREMENT 47 8.1 STANDARD REQUIREMENT 47 8.2 EUT ANTENNA 47 9 . EUT TEST PHOTO 48 APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Page 5 of 49 Report No.: NTEK-2014NT0620972F 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15 (15.247) , Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS 15.247 (a)(2) 6dB Bandwidth PASS 15.247 (b) Peak Output Power PASS 15.247 (c) Radiated Spurious Emission PASS 15.247 (d) Power Spectral Density PASS 15.205 Band Edge Emission PASS 15.203 Antenna Requirement PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report Page 6 of 49 Report No.: NTEK-2014NT0620972F 1.1 TEST FACILITY NTEK Testing Technology Co., Ltd Add.:1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street, Bao’an District, Shenzhen P.R. China. FCC Registration No.:238937; IC Registration No.:9270A-1 CNAS Registration No.:L5516 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission Test ±1.38dB 2 RF power,conducted ±0.16dB 3 Spurious emissions,conducted ±0.21dB 4 All emissions,radiated(<1G) ±4.68dB 5 All emissions,radiated(>1G) ±4.89dB 6 Temperature ±0.5°C 7 Humidity ±2% Page 7 of 49 Report No.: NTEK-2014NT0620972F 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment OPCOM-1 Trade Name OPCOM Link Model Name OPL301 Serial Model N/A Model Difference N/A Product Description The EUT is a OPCOM-1 Operation Frequency: 802.11b/g/n(20MHz): 2412~2462MHz Modulation Type: CCK/OFDM/DBPSK Bit Rate of Transmitter 802.11b:11/5.5/2/1 Mbps 802.11g:54/48/36/24/18/12/9/6Mbps 802.11n(20MHz):150/144.44/130/117/ 115.56/104/86.67/78/52/6.5Mbps Number Of Channel 802.11b/g/n20MHz:11CH Antenna Designation: Please see Note 3. Antenna Gain (dBi) 1.8 dBi Channel List Please refer to the Note 2. Ratings DC 12V Adapter Model:DSA-18PFG-12 FUS 120125 Input: 100-240V~,50/60Hz, 0.6A Output: 12V , 1.25A Battery N/A Connecting I/O Port(s) Please refer to the User's Manual Note: 1. For a more detailed features description, pl…

Text truncated - open the document above for the full version.

Page 48 of 49 Report No.: NTEK-2014NT0620972F 9. EUT TEST PHOTO Radiated Measurement Photos Page 49 of 49 Report No.: NTEK-2014NT0620972F Conducted Measurement Photos