2ADZKFT900Activity Tracker

Activity Tracker User Manual Model: FT900 Page 1 Package content This product contains an item: • Activity Tracker Activity Tracker layout Page 2 Wearing To calculate your movement accurately, wear the Activity Tracker in your left/right wrist. Replacing the Battery In replacing the battery, here are the procedures : 1. Unscrew the four screws (See label A). 2. Remove the back case (See label B). 3. Label C is the battery. It is now ready to be re placed. Page 3 Specifications Type Description General Type Wearable Tracking metrics Motion / Ste p s Processor nRF-51822 Memory 2Mb ( 256 KB) + 2Mb Fl ash Me mory Water Resistance 3 ATM Power Battery life 150 days Syncing and connectivity Syncing type Wireless (Bluetooth Low Energy) Display Screen resolution 144 x 168 mm Screen type TFT FCC Notice This device complies with part 15 of the FCC Rules . Operation is s ubject to the following two conditions : 1. This device may not caus e harmful interfe rence, and 2. This device mus t accept any interference received, including interfe rence that may caus e undes ired operation. WARNING Changes or modifications not expres s ly approved by the party res pons ible for compliance could void the us er’s authority to ope rate the equipment. NOTE This equipment has been tes ted and found to comply with the limits for a Class B digital device, purs uant to part 15 of the FCC Rules . Thes e limits are des igned to provide reas onable protection against harmful interference in a residential installation. This equipment generates, us es and can radiate radio frequency ene rgy and, if not ins talled and us ed in accordance with the ins tructions , may caus e harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does caus e harmful interfe rence to radi o or televis ion reception, which can be determined by turning the equipme nt off and on, the us er is encouraged to try to correct the interference by one or more of the following measures: Page 4 • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Cons ult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation expos ure limits s et forth for an uncontrolled environme nt. End us er mus t follow the s pecific operating ins tructions for s atis fying RF expos ure compliance. This trans mitte r mus t not be co-located or operating in conjunction with any other antenna or trans mitter. The portable device is designed to meet the re quire me nts for expos ure to radio waves es tablis hed by the Fede ral Communications Commis s ion (USA). Thes e requireme nts s et a SAR limit of 1.6 W/kg averaged over one gram of tis s ue. The highes t SAR value reported unde r this s tandard during product certification for us e when prope rly worn on the body is W/kg. Page 5

1 Photographs - EUT Constructional Details Test Model No.: FT900

Serial No. label 20mm 1:1 5.5mm Fixed: 0002=PE961 Serial no.: 000001, 000002, 000003, 000004 etc... 20mm 1:1 5.5mm Fixed: 0002=PE961 Serial no.: 000001, 000002, 000003, 000004 etc... MODEL:FT900 FCC ID:NTMFT900 PATENT PENDING MODEL:FT900 FCC ID:NTMFT900 PATENT PENDING MODEL:FT900 FCC ID:NTMFT900 PATENT PENDING MODEL:FT900 FCC ID:NTMFT900 PATENT PENDING MODEL:FT900 FCC ID:NTMFT900 PATENT PENDING MODEL:FT900 FCC ID:NTMFT900 PATENT PENDING DETAILS: FONT: ARIAL BOLD FONT SIZE: 4.55 pt POSITION: CENTER OF BACK CASE 9.60 mm 9.60 mm 26.00 mm 5.50 mm MODEL:FT900 FCC ID:2ADZKFT900 PATENT PENDING MODEL:FT900 FCC ID:2ADZKFT900 PATENT PENDING MODEL:FT900 FCC ID:2ADZKFT900 PATENT PENDING 5.19 mm5.19 mm

1 Photographs - EUT Constructional Details Test Model No.: FT900

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM130100036302 Page: 1 of 6 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page SAR Evaluation Report Application No.: SZEM1501000320CR Applicant: Fortify Technologies, LLC. Manufacturer: iDT Technology Limited Factory: iDT Technology Limited Product Name: Activity Tracker Model No.(EUT): FT900 FCC ID: 2ADZKFT900 Standards: 47 CFR Part 1.1307 (2014) 47 CFR Part 2.1093 (2014) KDB447498D01 General RF Exposure Guidance v05 Date of Receipt: 2015-01-22 Date of Test: 2015-01-23 to 2015-01-27 Date of Issue: 2015-01-30 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM130100036302 Page: 2 of 6 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2015-01-30 Original Authorized for issue by: Tested By 2015-01-27 (Eric Fu) /Project Engineer Date Prepared By 2015-01-30 (Linlin Lv) /Clerk Date Checked By 2015-02-03 (Kevin Feng) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM130100036302 Page: 3 of 6 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Contents Page 1 COVER PAGE .............................................................................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM150100032001 Page: 1 of 48 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page FCC REPORT Application No: SZEM1501000320CR Applicant: Fortify Technologies, LLC. Manufacturer: iDT Technology Limited Factory: iDT Technology Limited Product Name: Activity Tracker Model No.(EUT): FT900 FCC ID: 2ADZKFT900 Standards: 47 CFR Part 15, Subpart C (2014) Date of Receipt: 2015-01-22 Date of Test: 2015-01-23 to 2015-01-27 Date of Issue: 2015-01-30 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM150100032001 Page: 2 of 48 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2015-01-30 Original Authorized for issue by: Tested By 2015-01-27 (Eric Fu) /Project Engineer Date Prepared By 2015-01-30 (Linlin Lv) /Clerk Date Checked By 2015-02-03 (Kevin Feng) /Reviewer Date SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM150100032001 Page: 3 of 48 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Test Summary Test Item Test Requirement Test method Result Antenna Requirement 47 CFR Part 15, Subpart C Section 15.203/15.247 (c) ANSI C63.10 2009 PASS Conducted Peak Output Power 47 CFR Part 15, Subpart C Se…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Page: 1 of 7 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” Appendix A Photographs of EUT Constructional Details for SZEM1501000320CR SGS-CSTC Standards Technical Services Ltd. Page: 2 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Photographs - EUT Constructional Details Test Model No.: FT900 SGS-CSTC Standards Technical Services Ltd. Page: 3 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” SGS-CSTC Standards Technical Services Ltd. Page: 4 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduce…

Text truncated - open the document above for the full version.

1 Photographs - EUT Test Setup Test model No.: FT900 1.1 Radiated Emission 1.2 Radiated Spurious Emission