2AE6B1228Walkie Talkies

Federal Communication Commission Interference Statement FCC ID: 2AE6B1228 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Radiation Exposure Statement: This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless device employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. Tests for SAR are conducted using standard operating positions (10mm for Face up, 0mm for Back touch) accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. The device is authorized to operate at a duty factor not to exceed 50%. The use of holsters and similar accessories should not contain metallic components in its assembly, the use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.

Rev1/26/2023 ChenghaiXianxinPlasticToysFactory FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 USA Date:2026-06-11 FCCID:2AE6B1228 Ref.#1:AttestationStatementsPart2.911(d)(5)(i)Filing ChenghaiXianxinPlasticToysFactorycertifiesthattheequipmentforwhichauthorizationissoughtis not“covered”equipmentprohibitedfromreceivinganequipmentauthorizationpursuanttosection 2.903oftheFCCrules. ChenghaiXianxinPlasticToysFactorycertifiesthattheequipmentforwhichauthorizationissoughtdoes notincludecybersecurityoranti-virussoftwareproducedorprovidedbyKasperskyLab,Inc.oranyofits successorsandassignees,includingequipmentwithintegratedKasperskyLab,Inc.(oranyofits successorsandassignees)cybersecurityoranti-virussoftwarepursuanttoDA-24-886andKDB986446 D01CoveredEquipmentGuidancesectionB(2a). Deviceisinherentlycompliantbasedonhardwarelimitationsorsoftwarecontrols. or ASoftwareBillofMaterials(SBOM)isprovidedtotheTCBforreview,and Theend-userorthirdpartiescannotinstalladditionalsoftwareonthisdevice. Ref.#2:AttestationStatementsPart2.911(d)(5)(ii)Filing ChenghaiXianxinPlasticToysFactorycertifiesthat,asofthedateofthefilingoftheapplication,the applicantisnotidentifiedontheCoveredList(asaspecificallynamedentityoranyofitssubsidiariesor affiliates)asanentityproducing“covered”equipment. Applicant:ChenghaiXianxinPlasticToysFactory Address:ZhenXingRoad,PuMei,ChenghaiDistrict,ShantouCity,Guangdong,China ContactPerson:XinWu Tel.:+8613411938563 Email:[email protected] Sincerely, Signature:

ChenghaiXianxinPlasticToysFactory OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USA Date:June12,2026 Subject;RequestforConfidentiality FCCID: 2AE6B1228 ToWhomItMayConcern, PursuanttotheprovisionsoftheCommission’srulesTitle47Sections§0.457and§0.459,we arerequestingtheCommissiontowithholdthefollowingattachment(s)asconfidential documentsfrompublicdisclosureindefinitely. Thesedocumentscontaindetailedsystemandequipmentdescriptionsandareconsideredas proprietaryinformationinoperationoftheequipment.Thepublicdisclosureofthese documentsmightbeharmfultoourcompanyandwouldgivecompetitorsanunfairadvantage inthemarket. SchematicDiagram BlockDiagram PartsList OperationalDescription Tune-upProcedure SOFTWARESECURITYREQUIREMENTSFORU-NIIDEVICES Inadditionaltoabovementioneddocuments,inordertocomplywiththemarketingregulations inTitle47CFR§2.803andtheimportationrulesinTitle47CFR§2.1204,whileensuringthat businesssensitiveinformationremainsconfidentialuntiltheactualmarketingofnewly authorizeddevices,werequestShortTermConfidentialityofthefollowingattachment(s); ExternalPhotos TestSetupPhotos InternalPhotos UserManual For45days,pursuanttoPublicNoticeDA04-1705. OR For180dayspursuanttoKDB726920D01. Itisourunderstandingthatallmeasurementtestreports,FCCIDlabelformatand correspondenceduringthecertificationreviewprocesscannotbegrantedasconfidential documentsandthisinformationwillbeavailableforpublicreviewoncethegrantofequipment authorizationisissued. Sincerely, Signature: Name:XinWu Title:Manager

EffectiveDate:April2,2020QSF7.6.4-8–AgentAuthorizationLetterTemplatePage1of1 RevisionDate:Revision:0 ChenghaiXianxinPlasticToysFactory Date：2026-06-11 ProductModelNumber:1228-17,1228-7,1228-7A,1228-7B,1228-8,1228-9,1228-10,1228-16,1228-18, 1228-19,1228-20,1228-21,1228-22,1228-23,1228-25,1228-26,1228-27 FCCID：2AE6B1228 Towhomitmayconcern, Re:ProductCertificationRepresentativeAuthorizationLetter WeauthorizeQAILaboratoriesLtd.3980NorthFraserWay,BurnabyB.C.CanadaV5J5K5to actonourbehalfonallmattersconcerningtheabovenamedequipment. Thisshallincludethefollowing: Testing Approvalapplicationsandprocedures  WedeclarethatQAILaboratoriesLtd.isallowedtoforwardallinformationrelatedtothe approvalprojecttotheappliedcertificationbodyandtothenotificationentitiesandtodiscuss anyissuesconcerningtheapprovalapplication.AnyandallactscarriedoutbyQAI LaboratoriesLtd.onourbehalfshallhavethesameeffectasactsofourown. Signature: By:XinWu ContactListedonFCCWesbite Title:Manager Email:[email protected] Onbehalfof:ChenghaiXianxinPlasticToysFactory

ChenghaiXianxinPlasticToysFactory DeclarationLetterofModelDifference Date:2026-06-11 FCCID:2AE6B1228 TestedModelNumber:1228-17, AddingModelNumber(s):1228-7,1228-7A,1228-7B,1228-8,1228-9,1228-10,1228-16, 1228-18,1228-19,1228-20,1228-21,1228-22,1228-23,1228-25,1228-26,1228-27 AllAddingModelNumber(s)is/aresameelectricallyidenticalasTestedModelNumber.Onlythe model,colorandappearancearedifferent. YoursSincerely, Applicant:ChenghaiXianxinPlasticToysFactory Address:ZhenXingRoad,PuMei,ChenghaiDistrict,ShantouCity,Guangdong,China ContactPerson:XinWu Tel.:+8613411938563 Email:[email protected] Sincerely, Signature:

Page 1 of 11 Report No.: LGT26E202 Appendix - External Photographs of EUT Constructional Details Photo 1 Photo 2 Page 2 of 11 Report No.: LGT26E202 Appendix - External Photographs of EUT Constructional Details Photo 3 Photo 4 Page 3 of 11 Report No.: LGT26E202 Appendix - External Photographs of EUT Constructional Details Photo 5 Photo 6 Page 4 of 11 Report No.: LGT26E202 Appendix - External Photographs of EUT Constructional Details Photo 7 Photo 8 Page 5 of 11 Report No.: LGT26E202 Appendix - External Photographs of EUT Constructional Details Photo 9 Photo 10 Page 6 of 11 Report No.: LGT26E202 Appendix - External Photographs of EUT Constructional Details Photo 11 Photo 12 Page 7 of 11 Report No.: LGT26E202 Appendix - External Photographs of EUT Constructional Details Photo 13 Photo 14 Page 8 of 11 Report No.: LGT26E202 Appendix - External Photographs of EUT Constructional Details Photo 15 Photo 16 Page 9 of 11 Report No.: LGT26E202 Appendix - External Photographs of EUT Constructional Details Photo 17 Photo 18 Page 10 of 11 Report No.: LGT26E202 Appendix - External Photographs of EUT Constructional Details Photo 19 Photo 20 Page 11 of 11 Report No.: LGT26E202 Appendix - External Photographs of EUT Constructional Details Photo 21 Photo 22

Size: 12*18mm FCC ID: 2AE6B1228

Page 1 of 7 Report No.: LGT26E202 Appendix - Internal Photographs of EUT Constructional Details Photo 1 Photo 2 Page 2 of 7 Report No.: LGT26E202 Appendix - Internal Photographs of EUT Constructional Details Photo 3 Photo 4 ANT Page 3 of 7 Report No.: LGT26E202 Appendix - Internal Photographs of EUT Constructional Details Photo 5 Photo 6 Page 4 of 7 Report No.: LGT26E202 Appendix - Internal Photographs of EUT Constructional Details Photo 7 Photo 8 ANT Page 5 of 7 Report No.: LGT26E202 Appendix - Internal Photographs of EUT Constructional Details Photo 9 Photo 10 Page 6 of 7 Report No.: LGT26E202 Appendix - Internal Photographs of EUT Constructional Details Photo 11 Photo 12 Page 7 of 7 Report No.: LGT26E202 Appendix - Internal Photographs of EUT Constructional Details Photo 13

Page: 1/10 Ref : ACR.37.13.26.PAR.B Cancel and replace the report ACR.37.13.26.PAR.A SHENZHEN LGT TEST SERVICE CO., LTD. ROOM 205, BUILDING 13,ZONE B, ZHENXIONGINDUSTRIAL PARK, NO.177, RENMIN WEST ROAD,JINSHA, KENGZI STREET, PINGSHAN DISTRICT,SHENZHEN, GUANGDONG, CHINA MVG COMOSAR DOSIMETRIC E-FIELD PROBE SERIAL NO.: 0326-EPGO-431 Calibrated at MVG 13 Rue du Zephyr 91140 Villejust - FRANCE Calibration date: 2026/01/22 Scope available on :https://a2la.org/ Summary: This document presents the method and results from an accredited COMOSAR Dosimetric E-Field Probe calibration performed at MVG, using the CALIPROBE test bench, for use with a MVG COMOSAR system only. The test results covered by accreditation are traceable to the International System of Units (SI). COMOSAR E-Field Probe Calibration Report Docusign Envelope ID: 441A23A1-88DE-4D98-BD64-561319DF94DB COMOSAR E-FIELD PROBE CALIBRATION REPORT Ref: ACR.37.13.26.PAR.B Page: 2/10 Template_ACR.DDD.N.YY.MVGB.ISSUE_COMOSAR Probe vN This document shall not be reproduced, except in full or in part, without the written approval of MVG. The information contained herein is to be used only for the purpose for which it is submitted and is not to be released in whole or part without written approval of MVG. Name Function Date Signature Prepared by : Pedro Ruiz Technical Manager 2/6/2026 Checked & approved by: Pedro Ruiz Technical Manager 2/6/2026 Authorized by: Christophe Barrot Quality Manager Customer Name Distribution : SHENZHEN LGT TEST SERVICE CO., LTD Issue Name Date Modifications A Pedro Ruiz 2/6/2026 Initial release B Pedro Ruiz 04/10/2026 Update customer address Docusign Envelope ID: 441A23A1-88DE-4D98-BD64-561319DF94DB 2026 April 13 COMOSAR E-FIELD PROBE CALIBRATION REPORT Ref: ACR.37.13.26.PAR.B Page: 3/10 Template_ACR.DDD.N.YY.MVGB.ISSUE_COMOSAR Probe vN This document shall not be reproduced, except in full or in part, without the written approval of MVG. The information contained herein is to be used only for the purpose for which it is submitted and is not to be released in whole or part without written approval of MVG. TABLE OF CONTENTS 1 Device Under Test ..................................................................................................... 4 2 Product Description ................................................................................................... 4 2.1 General Information _______________________________________________________ 4 3 Measurement Method ................................................................................................ 4 3.1 Sensitivity _______________________________________________________________ 4 3.2 Linearity ________________________________________________________________ 4 3.3 Isotropy _________________________________________________________________ 5 3.4 Boundary Effect __________________________________________________________ 5 3.5 Probe Modulation Response _________________________________________________ 5 4 Measurement Uncertainty .......................................................................................... 6 5 Calibration Results ..................................................................................................... 6 5.1 Calibration in air __________________________________________________________ 6 5.2 Calibration in liquid _______________________________________________________ 7 6 Verification Results ................................................................................................... 8 7 List of Equipment ...................................................................................................... 9 Docusign Envelope ID: 441A23A1-88DE-4D98-BD64-561319DF94DB COMOSAR E-FIELD PROBE CALIBRATION REPORT Ref: ACR.37.13.26.PAR.B Page: 4/10 Template_ACR.DDD.N.YY.MVGB.ISSUE_COMOSAR Probe vN This document shall not be reproduced, except in full or in part, without the written approval of MVG. The information contained herein is to be used only for the purpose for which it is submitted and is not to be released in whole or part without written approval of MVG. 1 DEVICE UNDER TEST Device Under Test Device Type COMOSAR DOSIMETRIC E FIELD PROBE Manufacturer MVG Model SSE2 Serial Number 0326-EPGO-431 Product Condition (new / used) New Frequency Range of Probe 0.15 GHz-7.5GHz Resistance of Three Dipoles at Connector Dipole 1: R1=0.234 M Dipole 2: R2=0.234 M Dipole 3: R3=0.214 M 2 PRODUCT DESCRIPTION 2.1 GENERAL INFORMATION MVG’s COMOSAR E field Probes are built in accordance to the IEC/IEEE 62209-1528 and FCC KDB865664 D01 standards. Figure 1 – MVG COMOSAR Dosimetric E field Probe Probe Length 330 mm Length of Individual Dipoles 2 mm Maximum external diameter 8 mm Probe Tip External Diameter 2.5 mm Distance between dipoles / probe extremity 1 mm 3 MEASUREMENT METHOD The IEC/IEEE 62209-1528 and FCC KDB865664 D01 standards provide recommended practices for the probe calibrations, including the performance characteristics of interest and methods by which to assess their effect. All calibrations / measurements performed meet the fore-mentioned standards. 3.1 SENSITIVITY The sensitivity factors of the three dipoles were determined using a two step calibration method (air and tissue simulating liquid) using waveguides as outlined in the standards for frequency range 600- 7500MHz and using the calorimeter cell method (transfer method) as outlined in the standards for frequency 150-450 MHz. 3.2 LINEARITY The evaluation of the linearity was done in free space using the waveguide, performing a power sweep to cover the SAR range 0.01W/kg to 100W/kg. Docusign Envelope ID: 441A23A1-88DE-4D98-BD64-561319DF94DB COMOSAR E-FIELD PROBE CALIBRATION REPORT Ref: ACR.37.13.26.PAR.B Page: 5/10 Template_ACR.DDD.N.YY.MVGB.ISSUE_COMOSAR Probe vN This document shall not be reproduced, except in full or in part, without the written approval of MVG. The information contained herein is to be used only for the purpose for which it is submitted and is…

Text truncated - open the document above for the full version.

The test report is effective only with both signature and specialized stamp. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report only apply to the tested sample. Shenzhen LGT Test Service Co., Ltd. Tel: 0755-89668180 E-mail:[email protected] Web: www.lgt-cert.com Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Page 1 of 30 SAR TEST REPORT Product Name: Walkie Talkies Model Number: 1228-17, 1228-7, 1228-7A, 1228-7B, 1228-8, 1228-9, 1228- 10, 1228-16, 1228-18, 1228-19, 1228-20, 1228-21, 1228-22, 1228-23, 1228-25, 1228-26, 1228-27 FCC ID: 2AE6B1228 Issued For : Chenghai Xianxin Plastic Toys Factory ZhenXing Road, PuMei, Chenghai District, Shantou City, Guangdong, China Issued By : Shenzhen LGT Test Service Co., Ltd. Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Report Number: LGT26E202HA01 Sample Received Date: May 28, 2026 Date of Test June 03, 2026 – June 08, 2026 Date of Issue June 11, 2026 Max. SAR (1g) Body: 0.181 W/kg Reprot No.: LGT26E202HA01 Page 2 of 30 Table of Contents 1. General Information 5 1.1 EUT Description 5 1.2 Test Environment 6 1.3 Test Factory 6 2. Test Standards and Limits 7 3. SAR Measurement System 8 3.1 Definition of Specific Absorption Rate (SAR) 8 3.2 SAR System 8 4. Tissue Simulating Liquids 11 4.1 Simulating Liquids Parameter Check 11 5. SAR System Validation 13 5.1 Validation System 13 5.2 Validation Result 13 6. SAR Evaluation Procedures 14 7. EUT Antenna Location Sketch 15 8. EUT Test Position 16 8.1 Body-worn Position Conditions 16 9. Uncertainty 17 9.1 Measurement Uncertainty 17 9.2 System validation Uncertainty 18 10. Conducted Power Measurement 19 10.1 Test Result 19 10.2 Tune Up Power 19 11. EUT and Test Setup Photo 20 11.1 EUT Photos 20 11.2 Setup Photos 23 12. SAR Result Summary 24 12.1 Body-worn SAR 24 13. Equipment List 25 Appendix A. System Validation Plots 26 Appendix B. SAR Test Plots 28 Appendix C. Probe Calibration and Dipole Calibration Report 30 Reprot No.: LGT26E202HA01 Page 3 of 30 Revision History Rev. Issue Date Contents 00 June 03, 2026 Initial Issue Reprot No.: LGT26E202HA01 Page 4 of 30 TEST REPORT CERTIFICATION Applicant Chenghai Xianxin Plastic Toys Factory Address ZhenXing Road, PuMei, Chenghai District, Shantou City, Guangdong, China Manufacture Chenghai Xianxin Plastic Toys Factory Address ZhenXing Road, PuMei, Chenghai District, Shantou City, Guangdong, China Product Name Walkie Talkies Trademark N/A Model Number 1228-7, 1228-7A, 1228-7B, 1228-8, 1228-9, 1228-10, 1228-16, 1228- 18, 1228-19, 1228-20, 1228-21, 1228-22, 1228-23, 1228-25, 1228- 26, 1228-27 Sample number LGT2605289-6 APPLICABLE STANDARDS STANDARD TEST RESULTS ANSI/IEEE Std. C95.1-2019 FCC 47 CFR Part 2 (2.1093) IEEE 1528: 2013 PASS Prepared by: Approved by: Deng Deng Engineer Vita Li Manager Reprot No.: LGT26E202HA01 Page 5 of 30 1. General Information Environmental evaluation measurements of specific absorption rate (SAR) distributions in emulated human head and body tissues exposed to radio frequency (RF) radiation from wireless portable devices for compliance with the rules and regulations of the U.S. Federal Communications Commission (FCC). 1.1 EUT Description Product Name Walkie Talkies Test Model Number 1228-17 Series Number 1228-7, 1228-7A, 1228-7B, 1228-8, 1228-9, 1228-10, 1228-16, 1228-18, 1228-19, 1228-20, 1228-21, 1228-22, 1228-23, 1228-25, 1228-26, 1228-27 Model Difference Only the model, color and appearance are different Device Category Portable Product stage Production unit RF Exposure Environment General Population / Uncontrolled Hardware Version KE-Y6314 Software Version KE-Y6314 Frequency Range 462.5625MHz Modulation Type: FM Max. Reported SAR(1g): Test distance: Face up:10mm Back Touch:0mm Mode Face up (with 10mm separation) Back Touch (with 0mm separation) Analog 0.072 0.181 Limit 1.6 W/kg Battery Capacity: 100mAh Rated Voltage: 3.7V Operating Mode Maximum continuous output Antenna Specification Dipole Antenna Reprot No.: LGT26E202HA01 Page 6 of 30 1.2 Test Environment Ambient conditions in the SAR laboratory: Items Required Temperature (°C) 18-25 Humidity (%RH) 30-70 1.3 Test Factory Company Name: Shenzhen LGT Test Service Co., Ltd. Address: Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Accreditation Certificate FCC Registration No.: 746540 CAB ID: CN0136 Reprot No.: LGT26E202HA01 Page 7 of 30 2. Test Standards and Limits No. Identity Document Title 1 47 CFR Part 2 Frequency Allocations and Radio Treaty Matters; General Rules and Regulations 2 ANSI/IEEE Std. C95.1-2019 IEEE Standard for Safety Levels with Respect to Human Exposure to Electric, Magnetic, and Electromagnetic Fields, 0 Hz to 300 GHz 3 IEEE Std. 1528-2013 Recommended Practice for Determining the Peak Spatial- Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques 4 FCC KDB 447498 D01 v06 Mobile and Portable Device RF Exposure Procedures and Equipment Authorization Policies 5 FCC KDB 865664 D01 v01r04 SAR Measurement 100 MHz to 6 GHz 6 FCC KDB 865664 D02 v01r02 RF Exposure Reporting 7 FCC KDB 648474 D04 v01r03 SAR Evaluation Considerations for Wireless Handsets (A). Limits for Occupational/Controlled Exposure (W/kg) Whole-Body Partial-Body Hands, Wrists, Feet and Ankles 0.4 8.0 20.0 (B). Limits for General Population/Uncontrolled Exposure (W/kg) Whole-Body Partial-Body Hands, Wrists, Feet and Ankles 0.08 1.6 4.0 NOTE: Whole-Body SAR is averaged over the entire body, partial-body SAR is averaged over any 1 gram of tissue defined as a tissue volume in the shape of a cube. SAR for hands, wrists, feet and ankles is averaged over any 10 grams o…

Text truncated - open the document above for the full version.

The test report is effective only with both signature and specialized stamp. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report only apply to the tested sample. Shenzhen LGT Test Service Co., Ltd. Tel: 0755-89668180 E-mail:[email protected] Web: www.lgt-cert.com Room 205, Building 13, Zone B, Chen Hsong Industrial Park, No.177 Renmin West Road, Jinsha Community, Kengzi Street, Pingshan New District, Shenzhen, China RF TEST REPORT Product Name: Walkie Talkies Model Number: 1228-17, 1228-7, 1228-7A, 1228-7B, 1228-8, 1228-9, 1228-10, 1228-16, 1228-18, 1228-19, 1228-20, 1228-21, 1228-22, 1228-23, 1228-25, 1228-26, 1228-27 FCC ID: 2AE6B1228 Issued For : Chenghai Xianxin Plastic Toys Factory ZhenXing Road, PuMei, Chenghai District, Shantou City, Guangdong, China Issued By : Shenzhen LGT Test Service Co., Ltd. Room 205, Building 13, Zone B, Chen Hsong Industrial Park, No.177 Renmin West Road, Jinsha Community, Kengzi Street, Pingshan New District, Shenzhen, China Report Number: LGT26E202RF01 Sample Received Date: May 27, 2026 Date of Test: May 27, 2026 – June 11, 2026 Date of Issue: June 11, 2026 Report No.: LGT26E202RF01 Page 2 of 25 TEST REPORT CERTIFICATION Applicant: Chenghai Xianxin Plastic Toys Factory Address: ZhenXing Road, PuMei, Chenghai District, Shantou City, Guangdong, China Manufacturer: Chenghai Xianxin Plastic Toys Factory Address: ZhenXing Road, PuMei, Chenghai District, Shantou City, Guangdong, China Product Name: Walkie Talkies Trademark: N/A Model Number: 1228-17, 1228-7, 1228-7A, 1228-7B, 1228-8, 1228-9, 1228-10, 1228-16, 1228-18, 1228-19, 1228-20, 1228-21, 1228-22, 1228-23, 1228-25, 1228-26, 1228-27 Sample Status: Normal APPLICABLE STANDARDS STANDARD TEST RESULTS FCC Part 95 TIA 603-E-2016 PASS Prepared by: Approved by: Chris Chen Vita Li Engineer Technical Director Report No.: LGT26E202RF01 Page 3 of 25 Table of Contents Page 1. SUMMARY OF TEST RESULTS 6 1.1 TEST FACTORY 7 1.2 MEASUREMENT UNCERTAINTY 7 2. GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF THE EUT 8 2.2 DESCRIPTION OF THE TEST MODES 9 2.3 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 9 2.4 EQUIPMENTS LIST 10 3. FIELD STRENGTHS AND RADIATED SPURIOUS EMISSION 11 3.1 RADIATED EMISSION LIMITS 11 3.2 TEST PROCEDURE 11 3.3 TEST SETUP 12 3.4 EUT OPERATING CONDITIONS 12 3.5 TEST RESULT 13 4. SPURIOUS EMISSION ON ANTENNA PORT 14 4.1 LIMIT 14 4.2 TEST PROCEDURE 14 4.3 TEST SETUP 14 4.4 EUT OPERATION CONDITIONS 14 4.5 TEST RESULT 14 5. BANDWIDTH TEST 15 5.1 LIMIT 15 5.2 TEST PROCEDURE 15 5.3 TEST SETUP 15 5.4 EUT OPERATION CONDITIONS 15 5.5 TEST RESULTS 16 6. EFFECTIVE RADIATED POWER (E.R.P) 17 6.1 LIMIT 17 6.2 TEST PROCEDURE 17 6.3 TEST SETUP 17 6.4 TEST RESULTS 18 7. EMISSION MASK 19 7.1 LIMIT 19 Report No.: LGT26E202RF01 Page 4 of 25 Table of Contents Page 7.2 TEST PROCEDURE 19 7.3 TEST SETUP 19 7.4 EUT OPERATION CONDITIONS 19 7.5 TEST RESULT 20 8. FREQUENCY STABILITY 21 8.1 LIMIT 21 8.2 TEST PROCEDURE 21 8.3 TEST SETUP 21 8.4 EUT OPERATION CONDITIONS 21 8.5 TEST RESULT 22 9. MODULATION LIMIT 23 9.1 LIMIT 23 9.2 TEST PROCEDURE 23 9.3 TEST SETUP 23 9.4 TEST RESULT 24 Report No.: LGT26E202RF01 Page 5 of 25 Revision History Rev. Issue Date Contents 00 June 11, 2026 Initial Issue Report No.: LGT26E202RF01 Page 6 of 25 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part 95 Standard Section Test Item Judgment Remark FCC Part 95.567 Effective Radiated Power (e.r.p) PASS -- FCC Part 95.573 Authorized Bandwidth PASS -- FCC Part 95.579 Emission Mask PASS -- FCC Part 95.579 Transmitter Radiated Spurious Emission PASS -- FCC Part 95.579 Spurious Emission On Antenna Port PASS -- FCC Part 95.565 FCC Part 2.1055 Frequency Stability PASS -- FCC Part 95.575 FCC Part 2.1047 Modulation Limit PASS -- FCC Part 95.575 FCC Part 2.1047 Audio Frequency Response PASS -- NOTE: (1) ‘N/A’ denotes test is not applicable in this Test Report. Report No.: LGT26E202RF01 Page 7 of 25 1.1 TEST FACTORY Company Name: Shenzhen LGT Test Service Co., Ltd. Address: Room 205, Building 13, Zone B, Chen Hsong Industrial Park, No.177 Renmin West Road, Jinsha Community, Kengzi Street, Pingshan New District, Shenzhen, China Accreditation Certificate A2LA Certificate No.: 6727.01 FCC Registration No.: 746540 CAB ID: CN0136 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 RF output power, conducted ±0.68dB 2 Unwanted Emissions, conducted ±2.988dB 3 All emissions, radiated 9K-30MHz ±2.84dB 4 All emissions, radiated 30M-1GHz ±4.39dB 5 All emissions, radiated 1G-6GHz ±5.10dB 6 All emissions, radiated>6G ±5.48dB 7 Conducted Emission (9KHz-150KHz) ±2.79dB 8 Conducted Emission (150KHz-30MHz) ±2.80dB Report No.: LGT26E202RF01 Page 8 of 25 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF THE EUT Product Name: Walkie Talkies Test Model Number: 1228-17 Series Number: 1228-7, 1228-7A, 1228-7B, 1228-8, 1228-9, 1228-10, 1228-16, 1228-18, 1228-19, 1228-20, 1228-21, 1228-22, 1228-23, 1228-25, 1228-26, 1228-27 Model Difference: Only the model, color and appearance are different Operation Frequency: 462.5625MHz Modulation Type: FM Emission Type: 7K64F3E Antenna Type: Monopole Antenna Antenna Gain (dBi): 2 Channel List: Please refer to the Note 3. Battery: Capacity: 100mAh Rated Voltage: 3.7V Hardware Version: KE-Y6314 Software Version: KE-Y6314 Connecting I/O Port(s): Please refer to the Note 1. Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications or the User Manual. 2. The antenna information refers to the manufacturer provide report, applicable only to the tested sample identified in the report. Due to the incorrect antenna information, a series of problems such as the accuracy of the test results will be bor…

Text truncated - open the document above for the full version.

FCC ID_SAR Setup photos Body Face up (separation distance is 10mm) Body Back Touch (separation distance 0mm)

Page 1 of 1 Report No.: LGT26E202 Appendix - Test Setup photos Set-up for Radiated Spurious Emission, Below 1GHz Set-up for Radiated Spurious Emission, Above 1GHz