2AE77DGU12T5Q300SA2Car AVN

HYOLIM XE CO., LTD. 89, Seongseo4cheomdan-ro, Dalseo-gu, Daegu, Korea Attestation Statement – FCC §2.911(d)(5)(i) / Covered List (Kaspersky Lab) Non-Applicability Declaration Date: 25.11.25 Applicant: HYOLIM XE CO., LTD. FCC ID: 2AE77DGU12T5Q300SA2 Product Name: Car AVN Pursuant to §2.911(d)(5)(i) and §2.903 of the FCC rules, and in accordance with FCC Report and Order FCC-22-84 regarding equipment covered under the "Covered List", including cybersecurity and anti-virus software produced by Kaspersky Lab, Inc., its successors, and assignees, the undersigned hereby provides the following attestation. Declaration of Inherent Compliance The device referenced above is a Car AVN. It is a hardware-only product that: - Does not contain any operating system capable of running third-party software, - Has no storage capacity or memory architecture suitable for installing or executing software applications, - Cannot connect to the internet or external devices in any way other than via Bluetooth audio streaming and car phone projection , - Has no embedded or pre-installed cybersecurity or antivirus software, - Therefore, is not capable of storing or running any software included in the FCC's Covered List, including any software developed or distributed by Kaspersky Lab, Inc. Conclusion As such, this product is inherently compliant with FCC §2.903 and does not require a Software Bill of Materials (SBOM) under the FCC-22-84 order. Authorized Signature: Kisuk Lee / Manager HYOLIM XE CO., LTD.

Declaration of Equivalence For declaration of equality between a product variant to be certified with reference to an original product. To be issued and signed by the company responsible for the product variant. Declare on our sole responsibility that the product - Original Model Product Information Product ID: DGU-12T5-Q300SA-2 are in all relevant parts identical to the product - Variant Model Product Information Product ID: DGU-12T5-Q300SA-1, DGU-12T5-Q300SA-3, DGU-12T5-Q300SA-4, DGU-12T5-Q300SA-5, DGU-12T5-Q300SA-6 - The difference between (original design) and (variant design) is : DGU-12T5-Q300SA-1 : -Same Bare PCB, Camera support specification difference. (Variant model is completely same to original model(electrically and mechanically is same) HW : Camera AVM(Around view monitor) → RVC(Rear View Camera) SW : No change DGU-12T5-Q300SA-3 : -Same Bare PCB, Camera support specification, DAB and SW difference. (Variant model is completely same to original model(electrically and mechanically is same) HW : Camera AVM(Around view monitor) → RVC(Rear View Camera) Non DAB Board → DAB Board SW : Change Non-DAB function to DAB function DGU-12T5-Q300SA-4 : -Same Bare PCB, DAB and SW difference. (Variant model is completely same to original model(electrically and mechanically is same) HW : Non DAB Board → DAB Board SW : Change Non-DAB function to DAB function DGU-12T5-Q300SA-5 : -Same Bare PCB, Camera support specification and SW difference. (Variant model is completely same to original model(electrically and mechanically is same) HW : Camera AVM(Around view monitor) → RVC(Rear View Camera) SW : Change from KPH to MPH DGU-12T5-Q300SA-6 : -Same Bare PCB, SW difference. (Variant model is completely same to original model(electrically and mechanically is same) HW : No change SW : Change from KPH to MPH We, the undersigned, hereby declare that the Second Manufacturer Design is identical in both design and implementation. Signed by Company Name : HYOLIM XE CO.,LTD. Korea / 25 November, 2025 (Place, date of issue) (Signature / stamp) Kisuk Lee/ Manager

HYOLIM XE CO., LTD. 89, Seongseo4cheomdan-ro, Dalseo-gu, Daegu, Korea Rev 1/26/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 11-25-2025 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2AE77DGU12T5Q300SA2 HYOLIM XE CO., LTD. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. HYOLIM XE CO., LTD. (“the applicant”) certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Sincerely, Kisuk Lee / Manager HYOLIM XE CO., LTD. HYOLIM XE CO., LTD. 89, Seongseo4cheomdan-ro, Dalseo-gu, Daegu, Korea Rev 1/26/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 11-25-2025 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AE77DGU12T5Q300SA2 HYOLIM XE CO., LTD. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, Kisuk Lee / Manager HYOLIM XE CO., LTD.

Certification designating a U.S. Agent for service of process: As required by section 2.911(d)(7), the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. In either scenario, the designation of the U.S. agent for service of process should be provided as an attachment to the equipment authorization application. The applicant must provide a written certification, which must: i. Be signed by both the applicant and designated agent for service of process, if the agent is different from the applicant. ii. Acknowledge the applicant’s consent and the designated agent’s obligation to accept service of process. iii. Provide a physical U.S. address and email for the designated agent. iv. Acknowledge the applicant’s acceptance to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Unofficial information provided by FCC personnel on February 14, 2023, via the monthly call with the TCB Council: The Agent for Process of Service: • cannot be a TCB or affiliated with a TCB (e.g. could not be a person who works for a TCB or a company that owns or is owned by the TCB) • cannot be a [FCC recognised] Lab or affiliated with a test lab (e.g. could not be a person who works for a Lab or a company that owns or is owned by the Lab) • Agent can be Individual Entity or a Company Entity • Agent Entity must be located in US, US address/phone • Entity acting as Agent must have FRN (best practice, put FRN on Agent Letter) • Agent letter does not have to be FCC ID specific, can be general Agent for Grantee For devices being marketed or for which marketing has ceased for less than 1 year, if the Agent for Process of Service changes, then for every TC Number the TCB must request the FCC to put application into Audit Mode and Agent Letter needs to be updated (superseded). NOTE: The U.S. Agent for Service of Process should not be confused with the authorized agent used for signing the 731 form, other cover letters within the application, and/or the agent who may interface with the TCB. HYOLIM XE CO., LTD. 89, Seongseo4cheomdan-ro, Dalseo-gu, Daegu, Korea U.S. Agent Designation for Service of Process ATTENTION: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA REGARDING: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company Name: Approve-IT, Inc. Contact Name: Nathan Grinager Street Address: 8011 34 th Ave South, Suite 342 City/Province/Zip: Bloomington, MN 55425 Telephone No: 651-247-1678 Email: [email protected] FRN #: 0027533835 This letter is to confirm that we (“the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U.S. Agent Signature: Date: December 1, 2025 Signed by (Printed Name/Title): Nathan Grinager / Co-President *This letter must be dated within 1-year (update if other terms apply) of the date the application is submitted to the TCB for device certification The Applicant confirms its explicit consent and acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: HYOLIM XE CO., LTD. FCC ID: 2AE77DGU12T5Q300SA2 Contact Name: Kisuk Lee Address: 89, Seongseo4cheomdan-ro, Dalseo-gu, Daegu, Korea Zip: 704-801 Telephone No: +82 10-9250-6343 Email: [email protected] FRN #:0024717274 Applicant Signature: Date: Date: December 1, 2025 Signed by (Printed Name/Title): Kisuk Lee, Manager

HYOLIM XE CO., LTD. 89, Seongseo4cheomdan-ro, Dalseo-gu, Daegu, Korea Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: 2AE77DGU12T5Q300SA2 To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematics / Block Diagram / Operational Description / Parts List / PCB Layouts Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. 2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 180 days External Photos / Internal Photos / Test Setup Photos / User Manual / Construction Equality Declaration Pictures It is our understanding that all measurement test reports, FCC ID label format and correspondence during certification review process cannot be granted as confidential documents and such information will be available for public review once the grant of equipment authorization is issued. Sincerely Yours, Kisuk Lee / Manager HYOLIM XE CO., LTD.

HYOLIM XE CO., LTD. 89, Seongseo4cheomdan-ro, Dalseo-gu, Daegu, Korea Date: 2025.11.25 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. IIA LAB SERVICES, LLC 13146 NW 86th Drive Suite 400 Alachua Florida 32615 USA FCC ID : 2AE77DGU12T5Q300SA2 To whom it may concern: I, the undersigned, hereby authorize Technical Manager Kin Son of DEKRA Korea Co., Ltd. and here after referred to as DEKRA Korea Co., Ltd. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these m atters. Any and all acts carried out by Technical Manager Kin Son of DEKRA Korea Co., Ltd on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing DEKRA KOREA Co., Ltd. as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; HYOLIM XE CO., LTD. 89, Seongseo4cheomdan-ro, Dalseo-gu, Daegu, Korea e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Kisuk Lee / Manager HYOLIM XE CO., LTD. REMARK: 1. This authorization letter will be sent along with your application when filing with the Certification Division. 2. Please follow the format and type it on company letterhead and send original to us. 3. Authorized signature must be in agreement with grantee code contact in FCC database.

Copyright ⓒ DEKRA Korea Co., Ltd. All rights Reserved. Label Information Copyright ⓒ DEKRA Korea Co., Ltd. All rights Reserved. Label information Location&Drawing The location of the label is the top case.

South KoreaKorea, 17030 Tel.: +82-10-9250-6343Tel.: +82-31-338-8837 Fax: -Fax: +82-31-338-8847 In the configuration tested, the EUT complied with the standards specified above. Issue toIssue by HYOLIM XE CO., LTD.DEKRA Korea Co., Ltd. 89, Seongseo4chacheomdan-ro,498-2, Geumeo-ro, Pogok-eup, Dalseo-gu, Daegu,Cheoin-gu, Yongin-si, Gyeonggi-do, IC Number- ApplicantHYOLIM XE CO., LTD. ManufacturerHYOLIM XE CO., LTD. Date of Test(s)2025. 10. 28 ~ 2025. 11. 10 Date of Issue2025. 11. 25 RF EXPOSURE REPORT Equipment Under Test Car AVN Modle Name DGU-12T5-Q300SA-2 Variant Model Name DGU-12T5-Q300SA-1, DGU-12T5-Q300SA-3, DGU-12T5-Q300SA-4, DGU-12T5-Q300SA-5, DGU-12T5-Q300SA-6 FCC ID2AE77DGU12T5Q300SA2 Copyright ⓒ DEKRA Korea Co., Ltd. All rights Reserved. Page :1 / 27 Company name: DEKRA Korea Co., Ltd. Test site number : FCC (247193, KR0151), IC (24841) Address: 498-2, Geumeo-ro, Pogok-eup, Cheoin-gu, Yongin-si, Gyeonggi-do, 17030, Rep. of Korea Web site: http://www.dekra.kr Telephone: +82 31-338-8837 Facsimile: +82 31-338-8847 Laboratory Information Copyright ⓒ DEKRA Korea Co., Ltd. All rights Reserved. Page :2 / 27 1. Regulation RF EXPOSURE The SAR exclusion table from RSS-102 issue 5 is reproduced below: Table 1: SAR evaluation – Exemption limits for routine evaluation based on frequency and separation distance Frequency (MHz) Exemption Limits (mW) At separation distance of ≤5 mm At separation distance of 10 mm At separation distance of 15 mm At separation distance of 20 mm At separation distance of 25 mm ≤300 71 mW101 mW132 mW162 mW193 mW 45052 mW70 mW88 mW106 mW123 mW 83517 mW30 mW42 mW55 mW67 mW 19007 mW10 mW18 mW34 mW60 mW 24504 mW7 mW15 mW30 mW52 mW 35002 mW6 mW16 mW32 mW55 mW 58001 mW6 mW15 mW27 mW41 mW Frequency (MHz) Exemption Limits (mW) At separation distance of 30 mm At separation distance of 35 mm At separation distance of 40 mm At separation distance of 45 mm At separation distance of 50 mm ≤300 223 mW254 mW284 mW315 mW345 mW 450141 mW159 mW177 mW195 mW213 mW 83580 mW92 mW105 mW117 mW130 mW 190099 mW153 mW225 mW316 mW431 mW 580056 mW71 mW85 mW97 mW106 mW 245083 mW123 mW173 mW235 mW309 mW 350086 mW124 mW170 mW225 mW290 mW Copyright ⓒ DEKRA Korea Co., Ltd. All rights Reserved. Page :3 / 27 1. Regulation 2. RF Exposure Compliance Issue f=frequency in MHz, *= plane-wave equivalent power density MPE (Maximum Permissive Exposure) Prediction Predication of MPE limit at a given distance: Equation from page 18 of OET Bulletin 65, Edition 97-01 S = power density [mW/cm 2 ] P = Power input to antenna [mW] G = Power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna [cm] The information should be included in the user’s manual: This appliance and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. A minimum separation distance of 20 cm must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirements. 300 ~ 1 500//f/1 50030 1 500 ~ 15 000//130 1.34 ~ 30824/f2.19/f*(180/f2)30 30 ~ 30027.50.0730.230 According to §15.247(i), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission's guidelines. See § 1.1307(b)(1) of this Chapter. RF EXPOSURE Limits for Maximum Permissive Exposure: RF exposure is calculated. Limits for General Population / Uncontrolled Exposure 0.3 ~ 1.346141.63*(100)30 Frequency Range Electric Field Strength [V/m] Magnetic Field Strength [A/m] Power Density [mW/cm 2 ] Averaging Time [minute]  SPGRRPGS4 4 2  Copyright ⓒ DEKRA Korea Co., Ltd. All rights Reserved. Page :4 / 27 ( R : Distance to the center of the radiation of the antenna20 cm ) EIRP : Equivalent Isotropic Radiated Power (mW) - NOTE P : Max tuneup Power (dBm) G : Maximum Peak Antenna Gain (dBi) Power Density at the specific separation - NOTE- S dBi 7.40 dBm =5.50 mW = 4.00 dBm + mW/cm 2 = 0.001 093 3.40 - EIRP = P + G = Minimum : 2.00 5.50 / ( 4 X 20^2 X π ) = EIRP / (4 X R 2 π) = S : Maximum Power Density (mW/cm 2 ) dBm ) - Maximum Output Power for the Calculation :4.00 dBm Maximum : 4.00 dBm The EUT will only be used with a separation of 20 centimeters or greater between the antenna and the body of the The MPE calculation for this exposure is shown below. dBi (& - Maximum Peak Antenna Gain :3.40 1.00 dB - Measured RF Output Power :3.49 dBm - Target Power & Tolerance 3.00 dBm & ± MPE Calculations : Bluetooth (BDR) - Frequency Range : 2 402 MHz ~ 2 480 MHz Copyright ⓒ DEKRA Korea Co., Ltd. All rights Reserved. Page :5 / 27 ( = 0.001 376 mW/cm 2 EIRP : Equivalent Isotropic Radiated Power (mW) R : Distance to the center of the radiation of the antenna20 cm ) Power Density at the specific separation - S = EIRP / (4 X R 2 π) - NOTE = 6.92 / ( 4 X 20^2 X π ) S : Maximum Power Density (mW/cm 2 ) P : Max tuneup Power (dBm) =8.40 dBmG : Maximum Peak Antenna Gain (dBi) =6.92 mW =5.00 dBm + 3.40dBi - Maximum Output Power for the Calculation :5.00 dBm The EUT will only be used with a separation of 20 centimeters or greater between the antenna and the body of the The MPE calculation for this exposure is shown below. - EIRP = P + G- NOTE Minimum : 3.00 dBm ) - Maximum Peak Antenna Gain :3.40 dBi dB ( Maximum : 5.00 dBm & - Measured RF Output Power :4.84 dBm - Target Power & Tolerance 4.00 dBm & ± 1.00 MPE Calculations : Bluetooth (EDR) - Frequency Range : 2 402 MHz ~ 2 480 MHz Copyright ⓒ DEKRA Korea Co., Ltd. All rights Reserved. Page :6 / 27 ( = 34.67 mW =9.50 dBm + 5.90dBi - Maximum Output Power for the Calculation :9.50 dBm The EUT will only be used with a separation of 20 centimeters or greater between the antenna and the body of the The MPE calculation for this exposure is shown below. - EIRP = P + G- NOTE Minimum : 7.50 dBm ) - Maximum Peak Antenna Gain :5.90 dBi = 0.006 898 mW/cm 2 EIRP : Equivalent Isotr…

Text truncated - open the document above for the full version.

DEKRA Korea Co., Ltd. Report Number: YI-QA-25-RF-I013 YI-QA-P016-04(0) Page : (1) of (68) Effective Data : 2022.01.06 FCC Part 15 Subpart B&C §15.247 Test Report Equipment Under Test Car AVN Model Name DGU-12T5-Q300SA-2 Variant Model Name DGU-12T5-Q300SA-1, DGU-12T5-Q300SA-3, DGU-12T5-Q300SA-4, DGU-12T5-Q300SA-5, DGU-12T5-Q300SA-6 FCC ID 2AE77DGU12T5Q300SA2 IC Number - Applicant HYOLIM XE CO., LTD. Manufacturer HYOLIM XE CO., LTD. Date of Test(s) 2025. 10. 28 ~ 2025. 11. 10 Date of Issue 2025. 11. 25 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full Issue to Issue by HYOLIM XE CO., LTD. 89, Seongseo4chacheomdan-ro, Dalseo-gu, Daegu, South Korea Tel.: +82-10-9250-6343 Fax: - DEKRA Korea Co., Ltd. 498-2, Geumeo-ro, Pogok-eup, Cheoin-gu, Yongin-si, Gyeonggi-do, 17030, Rep. of Korea Tel.: +82 31-338-8837 Fax: +82 31-338-8847 DEKRA Korea Co., Ltd. Report Number: YI-QA-25-RF-I013 YI-QA-P016-04(0) Page : (2) of (68) Effective Data : 2022.01.06 Revision history Revision Date of issue Description Revised by -- 2025.11.25 Initial - -- DEKRA Korea Co., Ltd. Report Number: YI-QA-25-RF-I013 YI-QA-P016-04(0) Page : (3) of (68) Effective Data : 2022.01.06 Table of contents 1. Applicant Information ................................................................................................... 4 2. Laboratory Information ................................................................................................. 4 3. Summary of test results................................................................................................ 5 4. EUT Description ............................................................................................................ 6 5. Measurement equipment .............................................................................................. 7 6. Antenna Requirement ................................................................................................... 8 7. DTS bandwidth & 99% bandwidth measurement ....................................................... 9 8. Maximum peak conducted output power .................................................................. 23 9. Peak power spectral density ...................................................................................... 33 10. Transmitter radiated spurious emissions and conducted spurious emissions .. 43 DEKRA Korea Co., Ltd. Report Number: YI-QA-25-RF-I013 YI-QA-P016-04(0) Page : (4) of (68) Effective Data : 2022.01.06 1. Applicant Information 1.1. Details of applicant Applicant : HYOLIM XE CO., LTD. Address : 89, Seongseo4chacheomdan-ro, Dalseo-gu, Daegu, South Korea Contact Person : KiSuk Lee Telephone : +82-10-9250-6343 Fax : - 1.2. Manufacturer Information Manufacturer : HYOLIM XE CO., LTD. Address : 89, Seongseo4chacheomdan-ro, Dalseo-gu, Daegu, South Korea 2. Laboratory Information Company name : DEKRA Korea Co., Ltd. Test site number : FCC (247193, KR0151), IC (24841) Address : 498-2, Geumeo-ro, Pogok-eup, Cheoin-gu, Yongin-si, Gyeonggi-do, 17030, Rep. of Korea Web site : http://www.dekra.kr Telephone : +82 31-338-8837 Facsimile +82 31-338-8847 DEKRA Korea Co., Ltd. Report Number: YI-QA-25-RF-I013 YI-QA-P016-04(0) Page : (6) of (68) Effective Data : 2022.01.06 4. EUT Description Kind of product Car AVN Model Name DGU-12T5-Q300SA-2 Variant Model Name DGU-12T5-Q300SA-1, DGU-12T5-Q300SA-3, DGU-12T5-Q300SA-4, DGU-12T5-Q300SA-5, DGU-12T5-Q300SA-6 FCC ID 2AE77DGU12T5Q300SA2 IC Number - Power supply DC 12.00 V Frequency range 2 412 MHz ~ 2 462 MHz (802.11b/g/n_HT20) 2 422 MHz ~ 2 452 MHz (802.11n_HT40) Modulation technique DSSS (802.11b), OFDM (802.11g/n_HT20/n_HT40) Number of channels 11 ch (802.11b/g/n_HT20) 7 ch (802.11n_HT40) Antenna gain / Type 5.90 dBi / PCB Antenna Test Site Registration Number FCC (247193, KR0151), IC (24841) H/W version / S/W version 1.0 / 1.0 Test S/W version ADB Command 4.1. Table for Test Modes and Frequency (WLAN) Preliminary tests were performed in different data rate to find the worst radiated emission. The data rate shown in the table below is the worst-case rate with respect to the specific test item. Investigation has been done on all the possible configurations for searching the worst cases. The following table is a list of the test modes shown in this test report. Mode Data rate (Worst case) Frequency (Freq. MHz) 802.11b 1 Mbps Lowest (2 412) / Middle (2 437) / Highest (2 462) 802.11g 6 Mbps Lowest (2 412) / Middle (2 437) / Highest (2 462) 802.11n_HT20 MCS0 Lowest (2 412) / Middle (2 437) / Highest (2 462) 802.11n_HT40 MCS0 Lowest (2 422) / Middle (2 437) / Highest (2 452) DEKRA Korea Co., Ltd. Report Number: YI-QA-25-RF-I013 YI-QA-P016-04(0) Page : (7) of (68) Effective Data : 2022.01.06 5. Measurement equipment Equipment Manufacturer Model Serial number Calibration Interval Calibration date Calibration due. Test Receiver R&S ESW44 103182 1 year 25.08.23 26.08.23 Signal Generator R&S SMB100A 178128 1 year 25.05.15 26.05.15 Spectrum Analyzer R&S FSVA40 101591 1 year 25.03.13 26.05.13 DC Power Supply R&S NGE100 102415 1 year 25.05.15 26.05.15 Power Sensor R&S NRP-Z85 102464 1 year 25.05.16 26.05.16 Horn Antenna R&S HF906 100236 1 year 25.06.05 26.06.05 Horn Antenna AH Systems SAS-572 269 1 year 25.05.26 26.05.26 Bi-Log Ant. S/B VULB 9161SE 4159 2 year 24.03.21 26.03.21 Loop Antenna ETS LINDGREN 6502 00118166 2 year 24.05.16 26.05.16 Power Amplifier TESTEK TK-PA18H 170013-L 1 year 25.05.12 26.05.12 Power Amplifier MITEQ PAM-840A 18050014 1 year 25.05.19 26.05.19 Controller INNCO CO3000 CO3000/812/34240914/L N/A N/A N/A Antenna Master INNCO MA4640-XP-ET None N/A N/A N/A RF Cable SUHNER SUCOFLEX100 84047746 6 month 25.06.23 25.12.23 RF Cable SUHNER SUCOFLEX102 801270/2 6 month 25.06.23 25.12.23 RF Cable SUHNER SUCOFLEX102 801532/2 6 month 25.06.23 25.12.23 Band Rejection Filter Micro-Tonics BRM50702 064 1 year 25.05.15 26.05.15 ※Remark Support equipme…

Text truncated - open the document above for the full version.

Copyright ⓒ DEKRA Korea Co., Ltd. All rights Reserved. Antenna Datasheet Dongguan YiJiaElectronics Communication Technology Co., Ltd. SPECIFICATION FORAPPROVAL C STOMER: C STOMERNO: P Av PARTNAME: SUPP ER NO: J100 BluetoothAntenna YJQ01. A Date FileNo Revision Date: Q “TY: CUSTOMER APPROVED BY APPROVAL CHIEFS PERVISOR ÿ SUPP ER SIGNATURE \ CHECKDESIGN f Xie ChenXingyi YJ-RD-F04-A addÿ Tel:0769-82586086 Fax:0769-82586086 NO. (Contents) (Number of Page) (Page Code) (Spec Cover) (Spec Item (Drawing) (Antenna Specification) S (S Parameter PassiveTest (Antenna Profile) Material Certificate ~45 RqHSJ RoHS Test Report N/AN/AN/A addÿ Tel:0769-82586086 Fax:0769-82586086 RoHS Compatible REV. DESCRIPTION DATE A A A A O CD •K YJ- B WIFI-V02 200.0±4.0 (D PCB Black .OMM PCB FPC1000XA.P01 CoaxialCable Black O.D.1.13 COA1000XA.P01 Mini Connector AuPlated Cu TER1000XA.P01 NO PARTNAME DESCRIPTION Material Part Number Q.TY Tel Dongguan YiJiaElectronics Communication Technology Co., Ltd. Fax:0769-81 PARTNAME: WiFi Antenna PART NO.: YJQ01. A APPROVED BY I CHECKED BY DESIGNED BY DATE: UNITS: mm SCALE: REVISION: A I Tolerance XX X.XX±0.15 X° ±30 Antenna Specification Electrical Properties Frequency 2.4-2.5GHz Impedance Ohm Nominal V.S.W.R Max Gain dBi Radiation Omni-directional Polarization Linear Physical Properties Gonnector IPEX Cable Type .D. 1.13mm Cable Length 200mm CableColor Black Operating Temp. ~ °C Storage Temp Humidity 25±5oC/<70% addÿ Tel:0769-82586086 Fax:0769-82586086 Agilent E IB S Parameter Test// BT Antenna Active Ch/Trace Response Stimulus Mkr/Analysis Instr State GHz -25.S6S dB GHz dE GHz dB Trl Sll LogMag lO.OQdB/ Ref O.OOOdB [Fl] ÿQCg Sll Polar CLin haseÿ Scale l.OOOU [Fl|| f Tr3 AAA SVR Ref [Fl] GHz GHz Hz Hz iHz J r- R2-- k Recall State Reudll by File Name Save Channel Recall Channel Save Type State &Cal Channel/Trace Disp Only Save TraceData... SaveSnP addÿ Tel:0769-82586086 Fax:0769-82586086 PassiveTestFor BT2.4G Freq EffiEffi Gain (MHz) (dB)(dBi) addÿ Tel:0769-82586086 Fax:0769-82586086 东莞市一佳电子通讯科技有限公司 Dongguan YiJia Electronics Communication Technology Co.,Ltd. 规格承认书 SPECIFICATION FOR APPROVAL 日期 Date 2022/05/13 编号 File No 22051302 版本 Revision 1.0 客户 CUSTOMER: 天有为 客户料号 CUSTOMER NO: J100 品名 WiFiAntenna 品名 PART NAME: WiFiAntenna 供方料号 SUPPLIER NO: YJQ01.097.001.302A 送样日期 Date: 送样数量Q“TY: 客户确认CUSTOMER APPROVED BY APPROVALCHIEFSUPERVISOR 供方确认SUPPLIER SIGNATURE APPROVALCHECKDESIGN add：东莞市长安镇沙头社区木鱼路59号元富工业区Tel:0769-82586086 Fax:0769-82586086 APPROVALCHECKDESIGN ChenGuoqiangXieLiChenXingyi YJ-RD-F04-A add：东莞市长安镇沙头社区木鱼路59号元富工业区 Tel:0769-82586086 Fax:0769-82586086 承认书项目表 NO. 内 容 （Contents） 页 数 （Number of Page） 页 码 （Page Code） 1承认书封面（Spec Cover）11 2承认书项目表（Spec Item ）12 3工程成品图 （Drawing）13 4天线规格（Antenna Specification）14 5S参数测试 （S Parameter ）15 6无源测试 （Passive Test ）36 ~ 8 7天线装配图（Antenna Profile）39 ~ 11 8材质证明（ Material Certificate ）3512 ~ 46 9RoHS报告（ RoHS Test Report ）**** 10N/AN/AN/A 11--- 12--- 13--- add：东莞市长安镇沙头社区木鱼路59号元富工业区 Tel:0769-82586086 Fax:0769-82586086 天线规格 Antenna Specification Electrical Properties Frequency 2.4-2.5GHz 5.15-5.85GHz Impedance50 Ohm Nominal V.S.W.R 2.0 [email protected] 2.5 [email protected] Gain 5.9 [email protected] 1.3 [email protected] RadiationOmni-directional Polarizati…

Text truncated - open the document above for the full version.