2AE7D-OP1003Bluetooth Speaker

FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Shenzhen One Point Digital Technology Co., Ltd Building 25B, Yuanshan area, Gongming street, Guangming new districts, Shenzhen City, China DATE :2015-06-26 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint Hank.Yan of Global United Technology Services Co., Ltd. 2nd Floor, Block No.2, Laodong Industrial Zone, Xixiang Road Baoan District Shenzhen Guangdong to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with Shenzhen One Point Digital Technology Co., Ltd and Building 25B, Yuanshan area, Gongming street, Guangming new districts, Shenzhen City, China Dated this / Day of 06/26/2015 / Agency agreement expiration date: 06/26/2016 By: Annie Chin Signature Printed Title: Foreign trade manager On behalf of : Shenzhen One Point Digital Technology Co., Ltd Telephone: +86 0755 83531092

Differences Declaration To whom concern, We company Shenzhen One Point Digital Technology Co., Ltd hereby declares: The product model(s) OP1001, OP1002, OP1004, OP1005, OP1006, OP1007, OP1008, OP1009, OP1010, OP1011, OP1012, OP1013, OP1014, OP1015, OP1016, OP1017, OP1018, OP1019, OP1020, OP1021, OP1022, OP1023, OP1024, OP1025, OP1026, OP1027, OP1028, OP1029, OP1030 are identical in the same PCB layout, interior structure and electrical circuits with the model OP1003 which tested in Global Unit Technology Co., Ltd., the only differences are the model name and appearance color for commercial purpose. Authorized signature: Date: 2015-07-10

Date:07/17/2015 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD FCC ID:2AE7D-OP1003 To Whom It May Concern: We,Shenzhen One Point Digital Technology Co., Ltd, are applying FCC DOC for product Bluetooth Speaker which model no. is OP1001, OP1002, OP1003, OP1004, OP1005, OP1006, OP1007, OP1008, OP1009, OP1010, OP1011, OP1012, OP1013, OP1014, OP1015, OP1016, OP1017, OP1018, OP1019, OP1020, OP1021, OP1022, OP1023, OP1024, OP1025, OP1026, OP1027, OP1028, OP1029, OP1030. the FCC DOC is doing at proper FCC authorized and recognized lab, and FCC DOC will be issued soon. If you have any question or concerns, pls. contact us. Sincerely, Client’s signature Client’s name / title Annie Chin / Foreign trade manager Contact information / address Tel: +86 0755 83531092 Address: Building 25B, Yuanshan area, Gongming street, Guangming new districts, Shenzhen City, China recognized MRA lab, and FCC DOC will be issued soon.

Shenzhen One Point Digital Technology Co., Ltd Building 25B, Yuanshan area, Gongming street, Guangming new districts, Shenzhen City, China 2015-06-26 Equipment Authorization Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AE7D-OP1003 Product Name: Bluetooth Speaker Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:  Schematics  Block diagram  Operational Description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 06/26/2015 By: Annie Chin Signature Printed Title: Foreign trade manager On behalf of : Shenzhen One Point Digital Technology Co., Ltd Telephone: +86 0755 8353109 2

Label Location:

Product Name: Bluetooth Speaker Model Name: OP1003 FCC ID: 2AE7D-OP1003

FCC ID: 2AE7D-OP1003 According to 447498 D01 General RF Exposure Guidance v05 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where --f(GHz) is the RF channel transmit frequency in GHz --Power and distance are rounded to the nearest mW and mm before calculation --The result is rounded to one decimal place for comparison eirp = pt x gt = (EXd) 2 /30 where: pt = transmitter output power in watts, gt = numeric gain of the transmitting antenna (unitless), E = electric field strength in V/m, --- 10 ((dBuV/m)/20) /10 6 d = measurement distance in meters (m) ---3m So pt = (EXd) 2 /30 x gt Field strength = 95.67dBuV/m @3m Ant gain= 1.3dBi; so Ant numeric gain=1.35 So pt={[10 (95.67) /10 6 x3] 2 /(30x1.35)}x1000 mW =0.821 mW So (0.821 mW /5mm)x √2.441 = 0.257<3 Then SAR evaluation is not required

Shenzhen Blue Asia Technology Limited. Report No.: GTSE15060109501 FCC REPORT Applicant: Shenzhen One Point Digital Technology Co., Ltd Address of Applicant: Building 25B, Yuanshan area, Gongming street, Guangming new districts, Shenzhen City, China Equipment Under Test (EUT) Product Name:Bluetooth Speaker Model No.: OP1001, OP1002, OP1003, OP1004, OP1005, OP1006, OP1007, OP1008, OP1009, OP1010, OP1011, OP1012, OP1013, OP1014, OP1015, OP1016, OP1017, OP1018, OP1019, OP1020, OP1021, OP1022, OP1023, OP1024, OP1025, OP1026, OP1027, OP1028, OP1029, OP1030 FCC ID: 2AE7D-OP1003 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.249:2014 Date of sample receipt: June 22, 2015 Date of Test: June 22-26, 2015 Date of report issued: June 26, 2015 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above. Authorized Signature: Laboratory Manager Report No.: GTSE15060109501 2Version Version No.DateDescription 00June 26, 2015Original Prepared By: Date: June 26, 2015 Project Engineer Check By:Date: June 26, 2015 Reviewer Shenzhen Blue Asia Technology LimitedProject No.: GTSE150601095RF C1419, Niulanqian Building, Mingzhi Road, LongHua New District, Shenzhen, ChinaPage 2 of 30 Tested By: Report No.: GTSE15060109501 3Contents Page 1 COVER PAGE .............................................................................................................................................1 2 VERSION ...................................................................................................................................................2 3 CONTENTS ...............................................................................................................................................3 4 TEST SUMMARY ......................................................................................................................................4 4.1 MEASUREMENT UNCERTAINTY.............................................................................................................4 5 GENERAL INFORMATION .......................................................................................................................5 5.1 CLIENT INFORMATION..........................................................................................................................5 5.2 GENERAL DESCRIPTION OF EUT..........................................................................................................5 5.3 TEST MODE.........................................................................................................................................7 5.4 DESCRIPTION OF SUPPORT UNITS........................................................................................................7 5.5 TEST FACILITY....................................................................................................................................7 5.6 TEST LOCATION..................................................................................................................................7 5.7 OTHER INFORMATION REQUESTED BY THE CUSTOMER..........................................................................7 6 TEST INSTRUMENTS LIST ......................................................................................................................8 7 TEST RESULTS AND MEASUREMENT DATA .......................................................................................9 7.1 ANTENNA REQUIREMENT......................................................................................................................9 7.2 CONDUCTED EMISSIONS....................................................................................................................10 7.3 RADIATED EMISSION METHOD............................................................................................................13 7.3.1 Field Strength of The Fundamental Signal..................................................................................15 7.3.2 Spurious emissions .....................................................................................................................16 7.3.3 Bandedge emissions...................................................................................................................20 7.4 20DBOCCUPY BANDWIDTH...............................................................................................................21 8 TEST SETUP PHOTO .............................................................................................................................23 9 EUT CONSTRUCTIONAL DETAILS.......................................................................................................25 Shenzhen Blue Asia Technology LimitedProject No.: GTSE150601095RF C1419, Niulanqian Building, Mingzhi Road, LongHua New District, Shenzhen, ChinaPage 3 of 30 Report No.: GTSE15060109501 4Test Summary Test ItemSection in CFR 47Result Antenna requirement15.203Pass AC Power Line Conducted Emission15.207Pass Field strength of the fundamental signal15.249 (a)Pass Spurious emissions15.249 (a) (d)/15.209Pass Band edge15.249 (d)/15.205Pass 20dB Occupied Bandwidth15.215 (c) Pass Pass: The EUT complies with the essential requirements in the standard. Remark ˖Test according to ANSI C63.4:2009 4.1 Measurement Uncertainty Test ItemFrequency RangeMeasurement UncertaintyNotes Radiated Emission9kHz ~ 30MHz 4.34dB (1) Radiated Emission30MHz ~ 1000MHz 4.24dB (1) Radiated Emission1GHz ~ 26.5GHz 4.68dB (1) AC Power Line Conducted Emission 0.15MHz ~ 30MHz3.45dB(1) Note (1): The measurement uncertainty is for coverage factor of k=2 and a level of confidence of 95%. Shenzhen Blue Asia Technology LimitedProject No.: GTSE150601095RF C1419, Niulanqian Building, Mingzhi Road, LongHua New District, Shenzhen, ChinaPage 4 of 30 Report No.: GTSE15060109501 5General Information 5.1 Client Information Applicant: Shenzhen One Point Digital Technology Co., Ltd Address of Applicant: Bu…

Text truncated - open the document above for the full version.

Radiated Emission Conducted Emission