2AEBCXP-PPortable printer

Mini mobile receipt printer M i n i m o b i l e r e c e i p t p r i n t e r POS-P100 User Manual Please keep user manual for reference No part of this manual can be changed without agreement. The company reverses the rights to modify the technology, components, software and hardware. You may ask the distributors for more product information. No part of chapter in this manual can be copied or transmitted in any format without permission. Warning : Notice Pls read the Chapter carefully before printing! Safety notice The printer is equipped with professional battery and power adapter. otherwise, it may cause product damaged, battery leakage, fire or explosion. If not use printer longer time, take out the battery, otherwise, it may cause battery leakage. The liquid of battery has corrosivity, if it is on Skin or clothes under incorrect instructions, pls wash it by water immediately. If it is in eyes, pls wash it clearly by water and go to see doctor. Don’t open paper house when printing or just finished working, and forbidden to touch printhead, it may cause scald by high temperature. The power plug as power disconnect device, and it is next to printer and easy to touch. Do not immerged the printer in water or rainy, it may cause damaged Don’t open the paper house when printing, it may cause unnormal working Don’t remove serial cable when COM port is working, it may cause data incomplete. The work distance not exceed 10 meters by Bluetooth printing, otherwise, it may cause messy code or not work. It works stable between 0°C and 45°C temperature, but higher or lower temperature may cause low quality printing. It may cause low quality printing and printer damaged by poor paper roll or longer storage roller printing. The printer will recharge after the battery all used up, then will guarantee life time. Charge and discharge times are over 500 times, and its function will be reduced with the times increasing. Use Warning Storage’s attentions The printer’s storing temperature is between -10°C60°C and humidity is between 10％ ~ 80％. If store the printer longer time, pls take the battery out and store it alone, otherwise, it may cause the battery not work, even leakage and printer damaged. If the battery stored more than 3 months, then recharge it after installed to avoid damage because of self-discharge. Pls select good quality of thermal paper roll if keep the receipts longer. Can not stored the paper roll in higher temperature or hotter environment. If it’s opened, pls stored it in cool environment. ~ Mini mobile receipt printerMini mobile receipt printer 0102 Power cable plug USB port Switch FEED button POWER LED STATUS LED Environmental requirements Storage temperature: -10°c~60°c Storage humidity: 10%~90% Working °cTemperature: 0~45°c humidity: 10~80%Working % Physical parameters Interface: Bluetooth+USB+Serial Gross weight: 0.19 kg (No paper roll) Dimension: 92.5×75.5×37mm (L×W×H) Paper roll diameter: ≤30mm Print 1D Bar code: UPC-A/UPC-E/JAN13（EAN13）JAN8（EAN8）/ ITF/CODABAR/CODE93CODE39//CODE128； Characters: Chinese GB18030 Printing method: Direct thermal Printing speed: 70mm/s Paper width: 58mm Paper thickness: 0.06~0.08mm Character per line: 384 dots/line Outlook and model number for printerFunctions and features Paper housePaper exit Mini mobile receipt printerMini mobile receipt printer Resolution: 8 dots (203dpi) 0304 Other Features Preparation Install battery Paper method: Easy paper loading Paper end sensor: STATUS LED is twinkle when paper runs out. Control commands: Compatible with ESC/POS commands set. Power : 2000 mAh rechargeable li-ion battery Charge: quick charge and can be full between 1 and 4 hours A single charge time available: 25% printer column is more than 90m and standby time is over 7 days. It is technical reference, if the battery used longer and may cause power capacity down and not sure printing time. Battery Battery house Install paper roll Plastic roller Paper house Paper roll Methods of application Mini mobile receipt printerMini mobile receipt printer 0506 Basic functions Start Press Power button for one second when it is off state, then it will enter to work and power LED is on. Dormancy state It will be in Dormancy state when lower power capacity. Then Power LED is off, STATUS is on, the printer stop working. Off state Press POWER button for one second under start state. The printer is off and all LEDs are off. Self-test The steps: Press FEED Button in off state, then restart power and release FEED, then the current state and printer settings showed on the bill. Standby state Manual Power button and it will enter standby state if printer not work longer, then will save battery level. Notes: the printer not work and receive any data if power indicator off and state LED on, if want print, then restart POWER and ready printing. Printer Test The printer can be tested by POS printer CD . Bluetooth connection The hander terminal with Bluetooth, laptop and other pos terminals can be printed by drive. P100 Mobile printer can be compatible with Bluetooth 2.0 version, and continue work for 10m. Besides, our default BT-Name is printer Bluetooth printer, BT-Pin is 123456, it may amend BT-Name and Pin by POS Test software. The master device should be paired to mobile printer before working, and Matching process initiated by the master device. The details of methods below: 1. Start printer 2. The master device search external Bluetooth Name 3. Select printer Bluetooth Printer if there are several external Bluetooth Names 4. Enter password 123456 5. Finished paired Pls reference manual of Bluetooth for details pairing. The mobile printer is ON state when pairing. Notice: if user not amend BT-Name, pls not start several printers meanwhile, then will not sure which one is paired successfully. Indicators and Beeper There are 2 indicators on printer. One is POWER, the other is STATUS. The each functions below: Mini mobile receipt printerMini mobile receipt printer 0708 Claim It is…

Text truncated - open the document above for the full version.

ZHUHAI HONOR TECHNOLOGY CO.LTD Statement Model No.: XP-P100,XP-P200,XP-P300,XP-P400, XP-P500,XP-P600,XP-P800,XP-P810,XP-P820,XP-P830 FCC ID: 2AEBCXP-P We hereby state that these models are identical in interior structure, electrical circuits and components, and just model names and appearance colors are different for the marketing requirement. Your assistance on this matter is highly appreciated. Sincerely, Client’s signature ： Client’s name / title：Wei Wu / Engineer Contact information / address ：5th Floor, 2 Building, No.613 Huawei Road,Xiangzhou District, Zhuhai, China

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (current) 4.0 5.0 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0 ZHUHAI HONOR TECHNOLOGY CO.LTD 2015-03-12 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, ZHUHAI HONOR TECHNOLOGY CO.LTD hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): Product Description: Portable printer Model name: XP-P100,XP-P200,XP-P300,XP-P400,XP-P500,XP-P600,XP-P800, XP-P810,XP-P820,XP-P830 FCC ID: 2AEBCXP-P Sincerely, Client’s signature ： Client’s name / title：Wei Wu / Engineer Contact information / address ：5th Floor, 2 Building, No.613 Huawei Road,Xiangzhou District, Zhuhai, China

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 ZHUHAI HONOR TECHNOLOGY CO.LTD 2015-03-12 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2AEBCXP-P We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Operational Description - Schematic The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature ： Client’s name / title：Wei Wu / Engineer Contact information / address ：5th Floor, 2 Building, No.613 Huawei Road,Xiangzhou District, Zhuhai, China

FCC ID: 2AEBCXP-P

Antenna

FCC ID : 2AEBCXP-P Portable device According to §15.247(e)(i) and §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to KDB 447498 D01 General RF Exposure Guidance v05, section 4.3.1 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, 16 where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation 17 The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. GFSK Frequency (MHz) Output Power(dBm) Output Power(mW) Target power (dBm) Calculation Value Threshold Value 2402 4.71 2.96 4 ± 1 0.98 3.0 2440 3.80 2.40 4 ± 1 0.99 3.0 2480 4.83 3.04 4 ± 1 1.00 3.0 Threshold at which no SAR required is ≤ 3.0 for 1-g SAR, Separation distance is 5mm. Conclusion: No SAR is required. SIMULTANEOUS TRANSMISSION EVALUATION N/A

REPORT NO. ATE20150286 Page 1 of 56 FCC ID: 2AEBCXP-P ACCURATE TECHNOLOGY CO. LTD APPLICATION CERTIFICATION On Behalf of ZHUHAI HONOR TECHNOLOGY CO.LTD Portable printer Model No.: XP-P100,XP-P200,XP-P300,XP-P400, XP-P500,XP-P600,XP-P800,XP-P810,XP-P820,XP-P830 FCC ID: 2AEBCXP-P Prepared for : ZHUHAI HONOR TECHNOLOGY CO.LTD Address : 5th Floor, 2 Building, No.613 Huawei Road,Xiangzhou District, Zhuhai, China Prepared by : ACCURATE TECHNOLOGY CO. LTD Address : F1, Bldg. A, Changyuan New Material Port, Keyuan Rd. Science & Industry Park, Nanshan, Shenzhen, Guangdong P.R. China Report Number : ATE20150286 Date of Test : Feb 04-Mar 03,2015 Date of Report : Mar 04,2015 REPORT NO. ATE20150286 Page 2 of 56 FCC ID: 2AEBCXP-P ACCURATE TECHNOLOGY CO. LTD TABLE OF CONTENTS Description Page Test Report Certification 1. GENERAL INFORMATION .......................................................................................................... 4 1.1. Description of Device (EUT)....................................................................................................................5 1.2. Description of Test Facility ......................................................................................................................6 1.3. Measurement Uncertainty.........................................................................................................................6 2. MEASURING DEVICE AND TEST EQUIPMENT ..................................................................... 7 3. OPERATION OF EUT DURING TESTING ................................................................................. 8 3.1. Operating Mode ........................................................................................................................................8 3.2. Configuration and peripherals ..................................................................................................................8 4. TEST PROCEDURES AND RESULTS ......................................................................................... 9 5. 20DB BANDWIDTH TEST............................................................................................................10 5.1. Block Diagram of Test Setup..................................................................................................................10 5.2. The Requirement For Section 15.247(a)(1) ............................................................................................10 5.3. EUT Configuration on Measurement .....................................................................................................10 5.4. Operating Condition of EUT ..................................................................................................................10 5.5. Test Procedure ........................................................................................................................................11 5.6. Test Result ..............................................................................................................................................11 6. CARRIER FREQUENCY SEPARATION TEST........................................................................ 13 6.1. Block Diagram of Test Setup..................................................................................................................13 6.2. The Requirement For Section 15.247(a)(1) ............................................................................................13 6.3. EUT Configuration on Measurement .....................................................................................................13 6.4. Operating Condition of EUT ..................................................................................................................13 6.5. Test Procedure ........................................................................................................................................14 6.6. Test Result ..............................................................................................................................................14 7. NUMBER OF HOPPING FREQUENCY TEST ......................................................................... 16 7.1. Block Diagram of Test Setup..................................................................................................................16 7.2. The Requirement For Section 15.247(a)(1)(iii) ......................................................................................16 7.3. EUT Configuration on Measurement .....................................................................................................16 7.4. Operating Condition of EUT ..................................................................................................................16 7.5. Test Procedure ........................................................................................................................................17 7.6. Test Result ..............................................................................................................................................17 8. DWELL TIME TEST ..................................................................................................................... 18 8.1. Block Diagram of Test Setup..................................................................................................................18 8.2. The Requirement For Section 15.247(a)(1)(iii) ......................................................................................18 8.3. EUT Configuration on Measurement .....................................................................................................18 8.4. Operating Condition of EUT ..................................................................................................................18 8.5. Test Procedure .....................................................................................................................................…

Text truncated - open the document above for the full version.