2AEEK-9005010029Single channel wireless control module

Mach-Wireless-SRC Dr. Mach Lamps + technology 59591210 Description – Mach-Wireless-SRC 26.05.2015 / Ed.01 / Die; Page 1 User Manual Index 1. General information .................................................................................................... 1 2. Hardware: ................................................................................................................... 1 2.1. Connection.............................................................................................................. 1 2.2. Settings................................................................................................................... 1 2.3. Assembly Diagramm ............................................................................................... 2 2.4. Example for linking-up............................................................................................. 2 3. User Information ......................................................................................................... 3 4. Operational Description............................................................................................... 4 1. General information The radio unit Mach-Wireless-SRC enables the operation of existing OT-lights from Dr.Mach GmbH & Co. KG in a wireless mode. The correct functioning of the wireless operation requires one radio unit installed in the light and a second radio unit installed inside the wall control housing. 2. Hardware: 2.1. Connection The radio unit consists of one radio board 67150216 and one radio module 67150215. The radio module is connected to the plug J3 on the radio board. The radio board must be connected to the I2C bus with the 4-pole JST-connectors (CN1 and CN2) between the main control and the key pad. These connectors are assigned with the power supply +5V (Pin1, Pin4) and with one I2C – interface (Pin2 , Pin3). 2.2. Settings The setting of the WCom-Unit is done with dip-switch S1. The WCom-Unit is designed to enable communication only between lights (radio units) with the same WCom-Unit. Settings can be done for a maximum number of 16 different WCom-Unit’s. Dip – Switch S1 (WCom – Unit) 1 2 3 4 WCom- Unit Off Off Off Off 1 On Off Off Off 2 Off On Off Off 3 On On Off Off 4 Off Off On Off 5 On Off On Off 6 Off On On Off 7 On On On Off 8 Off Off Off On 9 On Off Off On 10 Off On Off On 11 On On Off On 12 Off Off On On 13 On Off On On 14 Off On On On 15 On On On On 16 Mach-Wireless-SRC Dr. Mach Lamps + technology 59591210 Description – Mach-Wireless-SRC 26.05.2015 / Ed.01 / Die; Page 2 2.3. Assembly Diagramm 2.4. Example for linking-up Light 1 Wall panel WCom-Unit 5 WCom-Unit 5 Light 2 WCom-Unit 5 All devices are set for the same WCom-Unit . This enables the communication between the lights and the wall control. Radio board 67150216 Radio module 67150215 CN2 CN1 Dip Switch S1 Radio link Mach-Wireless-SRC Dr. Mach Lamps + technology 59591210 Description – Mach-Wireless-SRC 26.05.2015 / Ed.01 / Die; Page 3 3. User Information Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Request for Confidentiality Date: 09.06.2015 Subject: Confidentiality Request for: FCC ID: 2AEEK-9005010029 / IC: 20013-9005010029 Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 6.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 1 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual *Note: ______(Insert Explanation as Necessary)______ Dr. Mach GmbH & Co. KG has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180) 2 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By: ______________ Thomas Ring, Manager Certification (Signature/Title 3 ) CSA Group Bayern GmbH, Ohmstr. 1-4, 94342 Strasskirchen, Germany Phone: +49 9424 9481-250, Email: [email protected] 1 - The asterisked items (*) require further justification before permanent confidentiality will be allowed. These also currently require review by the FCC under their Permit-But-Ask policy before the grant is issued and can delay completion of an application. Further justification should be added to the note above. One such example for a potted device would be: “The EUT is FULLY potted using a non-removable epoxy based material. Removal of potting material causes irreparable damage to internal circuitry. See photographs exhibits that outline the device before and after potting.” 2 - Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 25.06.2015 Request for a Limited Modular Approval - FCC ID: 2AEEK-9005010029 Dear Sirs, Our client’s module with the above FCC ID is seeking FCC authorization as a Modular transmitter. The requirements of the FCC Public notice DA00-1407 and KDB 996369 are met. Please see the following comments: Please contact us if you have any additional questions. Item Requirements EUT 1 Have its own RF shielding No own RF shielding. Module will be installed by professional installers only into end devices of the Grantee, so full compliance of the end product is always ensured. 2 Have buffered modulation/data inputs (if such inputs are provided), The EUT has buffered data inputs. 3 Have it own power supply regulation 5 VDC Refer to operational description and test report. 4 Meet the antenna requirements of Section 15.203 The antenna is a small PCB integrated PIF type. Special tools are required for replacing the antenna, that prevents manipulation by user. No external power amplifier can be connected. The requirements of part 15.203 and 15.204 are met. 5 Be tested in a stand-alone configuration, i.e., the antenna, AC or DC power and data input/output lines must be connected to the module but, the module must not be inside another case during testing Device was tested in a stand-alone configuration on a Test Jig. Refer to setup photos & internal photos. 6 Be labelled with its own FCC ID number, and if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. The module has its own label. Refer to FCC ID label format and location file. 7 The modular transmitter is manufactured so that the user cannot influence the operation of the transmitter that will operate outside of the scope of the regulations. Module installation in hosts will require professional installation, therefore the user cannot influence the operation of the transmitter 8 Compliance with RF exposure requirements is the responsibility of the grantee and will be addressed for all final host configurations Compliance with RF exposure requirements Thomas Ring / Team Lead Global Market Access CSA Group Bayern GmbH, Ohmstr. 1-4, 94342 Strasskirchen, Germany Phone: +49 9424 9481 250, Email: [email protected]

CSA Group Bayern GmbH File No. T39444-00-xxTK, page 1 of 5 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 Attachment A Type / Model Name : Mach-Wireless-SRC Product Description : Single channel wireless control module Applicant : Dr. Mach GmbH Co. KG Address : Flossmannstraße 28 85560 EBERSBERG, GERMANY Manufacturer : calima engineering Address : Greimelstraße 26 83236 ÜBERSEE, GERMANY Licence holder : Dr. Mach GmbH Co. KG Address : Flossmannstraße 28 85560 EBERSBERG, GERMANY according to Test Report No. : T39444-00-xxTK 07. May 2015 ______________________________________________________________________________________________ Date of issue The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permission of the test laboratory. CSA Group Bayern GmbH File No. T39444-00-xxTK, page 2 of 5 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 Contents 1 Photo documentation of the EUT 3 1.1 EUT 3 1.2 EUT with keystroke simulation 4 1.3 Antenna structure 5 CSA Group Bayern GmbH File No. T39444-00-xxTK, page 3 of 5 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 1 Photo documentation of the EUT 1.1 EUT Top view Bottom view Wireless section CSA Group Bayern GmbH File No. T39444-00-xxTK, page 4 of 5 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 1.2 EUT with keystroke simulation CSA Group Bayern GmbH File No. T39444-00-xxTK, page 5 of 5 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 1.3 Antenna structure RF section and antenna application

25.03.2015 16:40:12 f=3.00 U:\1A_Projekte\Fernbedienung\FernbedienungLED2_5_Calima\Calima\67150216.01_Funkplatine LED2_5\Projekt\Eagle\150318\Mach-Wireless-SRC-01.brd

CSA Group Bayern GmbH File No. T39444-00-xxTK, page 1 of 5 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 Attachment A Type / Model Name : Mach-Wireless-SRC Product Description : Single channel wireless control module Applicant : Dr. Mach GmbH Co. KG Address : Flossmannstraße 28 85560 EBERSBERG, GERMANY Manufacturer : calima engineering Address : Greimelstraße 26 83236 ÜBERSEE, GERMANY Licence holder : Dr. Mach GmbH Co. KG Address : Flossmannstraße 28 85560 EBERSBERG, GERMANY according to Test Report No. : T39444-00-xxTK 07. May 2015 ______________________________________________________________________________________________ Date of issue The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permission of the test laboratory. CSA Group Bayern GmbH File No. T39444-00-xxTK, page 2 of 5 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 Contents 1 Photo documentation of the EUT 3 1.1 EUT 3 1.2 EUT with keystroke simulation 4 1.3 Antenna structure 5 CSA Group Bayern GmbH File No. T39444-00-xxTK, page 3 of 5 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 1 Photo documentation of the EUT 1.1 EUT Top view Bottom view Wireless section CSA Group Bayern GmbH File No. T39444-00-xxTK, page 4 of 5 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 1.2 EUT with keystroke simulation CSA Group Bayern GmbH File No. T39444-00-xxTK, page 5 of 5 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 1.3 Antenna structure RF section and antenna application

CSA Group Bayern GmbH File No. T39444-00-03TK, page 1 of 18 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 EMI − T E S T R E P O R T - Human Exposure - Type / Model Name : Mach-Wireless-SRC Product Description : Single channel wireless control module Applicant : Dr. Mach GmbH Co. KG Address : Flossmannstraße 28 85560 EBERSBERG, GERMANY Manufacturer : Dr. Mach GmbH Co. KG Address : Flossmannstraße 28 85560 EBERSBERG, GERMANY Licence holder : Dr. Mach GmbH Co. KG Address : Flossmannstraße 28 85560 EBERSBERG, GERMANY Test Result according to the standards listed in clause 1 test standards: POSITIVE Test Report No. : T39444-00-03TK 25. June 2015 ______________________________________________________________________________________________ Date of issue The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permission of the test laboratory. FCC ID: 2AEEK-9005010029 IC: 20013-9005010029 CSA Group Bayern GmbH File No. T39444-00-03TK, page 2 of 18 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 Contents 1 TEST STANDARDS 3 2 EQUIPMENT UNDER TEST 4 2.1 Photo documentation of the EUT – see ATTACHMENT A 4 2.2 Equipment type, category 4 2.3 Short description of the equipment under test (EUT) 4 2.4 Variants of the EUT 4 2.5 Operation frequency and channel plan 4 2.6 Transmit operating modes 5 2.7 Antennas 5 2.8 Power supply system utilised 5 2.9 Peripheral devices and interface cables 5 2.10 Final measurement conditions 6 3 TEST RESULT SUMMERY 7 3.1 Final assessment 7 4 TEST ENVIRONMENT 8 4.1 Address of the test laboratory 8 4.2 Environmental conditions 8 4.3 Statement of the measurement uncertainty 8 4.4 Measurement protocol for FCC and IC 9 5 TEST CONDITIONS AND RESULTS 10 5.1 Maximum peak output power 10 6 HUMAN EXPOSURE 12 6.1 Maximum permissible exposure (MPE) 12 6.2 Co-location and Co-transmission 14 6.3 SAR test exclusion considerations 15 6.4 Correction for pulsed operation (duty cycle) 17 ATTACHMENT A as separte supplement FCC ID: 2AEEK-9005010029 IC: 20013-9005010029 CSA Group Bayern GmbH File No. T39444-00-03TK, page 3 of 18 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 1 TEST STANDARDS The tests were performed according to following standards: FCC Rules and Regulations Part 1, Subpart I - Procedures Implementing the National Environmental Policy Act of 1969 Part 1, Subpart I, Section 1.1310 Radiofrequency radiation exposure limits Part 1, Subpart 2, Section 2.1093 Radiofrequency radiation exposure evaluation: portable device OET Bulletin 65, 65A, 65B Edition 97-01, August 1997 – Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. KDB 447498 D01 v05r02 Mobile and portable devices RF Exposure procedures and equipment authorisation policies, February 7, 2014. KDB 865664 D01 SAR Measurement Requirements for 100 MHz to 6 GHz, February 7, 2014. ANSI C95.1: 2005 IEEE Standard for Safety Levels with respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz ETSI TR 100 028 V1.3.1: 2001-03, Electromagnetic Compatibility and Radio Spectrum Matters (ERM); Uncertainties in the Measurement of Mobile Radio Equipment Characteristics—Part 1 and Part 2 FCC ID: 2AEEK-9005010029 IC: 20013-9005010029 CSA Group Bayern GmbH File No. T39444-00-03TK, page 4 of 18 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 2 EQUIPMENT UNDER TEST 2.1 Photo documentation of the EUT – see ATTACHMENT A 2.2 Equipment type, category Proprietary wireless transceiver, fixed equipment. 2.3 Short description of the equipment under test (EUT) The EUT is a 2.4 GHz wireless module on a micro controller module to send I²C-Bus commands within a modulated wireless transmission. A special test hardware is used to simulate a keystroke. The EUT has no external antenna and no temporary connector. All measurement are performed radiated. Number of tested samples: 1 Serial number: 67150216 Firmware version: V1.06 Mach-Wireless-SRC EUT configuration: (The CDF filled by the applicant can be viewed at the test laboratory.) 2.4 Variants of the EUT None 2.5 Operation frequency and channel plan Note: the marked frequencies are determined for final testing. Channel Frequency (MHz) Channel Frequency (MHz) Channel Frequency (MHz) Channel Frequency (MHz) 12400222421432442642463 22401232422442443652464 32402242423452444662465 42403252424462445672466 52404262425472446682467 62405272426482447692468 72406282427492448702469 82407292428502449712470 92408302429512450722471 102409312430522451732472 112410322431532452742473 122411332432542453752474 132412342433552454762475 142413352434562455772476 152414362435572456782477 162415372436582457792478 172416382437592458802479 182417392438602459812480 192418402439612460822481 202419412440622461832482 212420422441632462842483 FCC ID: 2AEEK-9005010029 IC: 20013-9005010029 CSA Group Bayern GmbH File No. T39444-00-03TK, page 5 of 18 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 2.6 Transmit operating modes The EUT uses GMSK modulation with a data rate of 250 kbps (kbps = kilobits per second) 2.7 Antennas The following antennas shall be used with the EUT: 2.8 Power supply system utilised Power supply voltage, V nom : 5 VDC (USB powered) Power supply voltage (alternative) : Input: 100-240 V, 47-63 Hz, 1  Power supply, Output: +5 VDC. 2.9 Peripheral devices and interface cables The following peripheral devices and interface cables are connected during the measurements: - Arduino controller system with LCD Model : Seeeduino v3.0 (Keyboard simulation) Arduino controller system with LCD Seeeduino v3.0 (Companion …

Text truncated - open the document above for the full version.

CSA Group Bayern GmbH File No. T39444-00-01TK, page 1 of 30 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 EMI − T E S T R E P O R T - FCC Part 15.249, RSS210 - Type / Model Name : Mach-Wireless-SRC Product Description : Single channel wireless control module Applicant : Dr. Mach GmbH Co. KG Address : Flossmannstraße 28 85560 EBERSBERG, GERMANY Manufacturer : Dr. Mach GmbH Co. KG Address : Flossmannstraße 28 85560 EBERSBERG, GERMANY Licence holder : Dr. Mach GmbH Co. KG Address : Flossmannstraße 28 85560 EBERSBERG, GERMANY Test Result according to the standards listed in clause 1 test standards: POSITIVE Test Report No. : T39444-00-01TK 24. June 2015 ______________________________________________________________________________________________ Date of issue The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test results without the written permission of the test laboratory. FCC ID: 2AEEK-9005010029 IC: 20013-9005010029 CSA Group Bayern GmbH File No. T39444-00-01TK, page 2 of 30 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 Contents 1 TEST STANDARDS 3 2 EQUIPMENT UNDER TEST 4 2.1 Photo documentation of the EUT – Detailed photos see attachment A 4 2.2 Equipment category 4 2.3 Short description of the equipment under test (EUT) 4 2.4 Variants of the EUT 4 2.5 Operation frequency and channel plan 4 2.6 Transmit operating modes 5 2.7 Antenna 5 2.8 Power supply system utilised 5 2.9 Peripheral devices and interface cables 5 2.10 Determination of worst case conditions for final measurement 5 3 TEST RESULT SUMMERY 7 3.1 Final assessment 7 4 TEST ENVIRONMENT 8 4.1 Address of the test laboratory 8 4.2 Environmental conditions 8 4.3 Statement of the measurement uncertainty 8 4.4 Measurement protocol for FCC and IC 9 5 TEST CONDITIONS AND RESULTS 10 5.1 AC power line conducted emissions 10 5.2 Field strength of fundamental 14 5.3 Out-of-band emission, radiated 16 5.4 EBW and OBW 23 5.5 Correction for pulsed operation (duty cycle) 26 5.6 RF exposure consideration for SAR test exclusion 28 5.8 Antenna application 29 6 USED TEST EQUIPMENT AND ACCESSORIES 30 ATTACHMENT A as separate supplement FCC ID: 2AEEK-9005010029 IC: 20013-9005010029 CSA Group Bayern GmbH File No. T39444-00-01TK, page 3 of 30 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 1 TEST STANDARDS The tests were performed according to following standards: FCC Rules and Regulations Part 15, Subpart A - General (September, 2014) Part 15, Subpart A, Section 15.31 Measurement standards Part 15, Subpart A, Section 15.33 Frequency range of radiated measurements Part 15, Subpart A, Section 15.35 Measurement detector functions and bandwidths FCC Rules and Regulations Part 15, Subpart C - Intentional Radiators (September, 2014) Part 15, Subpart C, Section 15.203 Antenna requirement Part 15, Subpart C, Section 15.204 External radio frequency power amplifiers and antenna modifications Part 15, Subpart C, Section 15.205 Restricted bands of operation Part 15, Subpart C, Section 15.207 Conducted limits Part 15, Subpart C, Section 15.209 Radiated emission limits, general requirements Part 15, Subpart C, Section 15.249 Operation within the bands 902 - 928 MHz, 2400 - 2483.5 MHz, 5725 - 5875 MHz, and 24.0 - 24.25 GHz ANSI C63.4: 2014 Methods of Measurement of Radio-Noise Emissions from Low- Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz. ANSI C63.10: 2013 Testing Unlicensed Wireless Devices ANSI C95.1:2005 IEEE Standard for Safety Levels with respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz CISPR 16-4-2: 2013 Uncertainty in EMC measurement CISPR 22: 2008 Information technology equipment EN 55022: 2010 KDB 447498 D01 General RF Exposure Guidance v05r02 FCC ID: 2AEEK-9005010029 IC: 20013-9005010029 CSA Group Bayern GmbH File No. T39444-00-01TK, page 4 of 30 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 2 EQUIPMENT UNDER TEST 2.1 Photo documentation of the EUT – Detailed photos see attachment A 2.2 Equipment category Proprietary wireless transceiver, fixed equipment. 2.3 Short description of the equipment under test (EUT) The EUT is a 2.4 GHz wireless module on a micro controller module to send I²C-Bus commands within a modulated wireless transmission. A special test hardware is used to simulate a keystroke. Number of tested samples: 1 Serial number: 67150216 Firmware version: V1.06 Mach-Wireless-SRC EUT configuration: (The CDF filled by the applicant can be viewed at the test laboratory.) 2.4 Variants of the EUT None 2.5 Operation frequency and channel plan Note: the marked frequencies are determined for final testing. Channel Frequency (MHz) Channel Frequency (MHz) Channel Frequency (MHz) Channel Frequency (MHz) 12400222421432442642463 22401232422442443652464 32402242423452444662465 42403252424462445672466 52404262425472446682467 62405272426482447692468 72406282427492448702469 82407292428502449712470 92408302429512450722471 102409312430522451732472 112410322431532452742473 122411332432542453752474 132412342433552454762475 142413352434562455772476 152414362435572456782477 162415372436582457792478 172416382437592458802479 182417392438602459812480 192418402439612460822481 202419412440622461832482 212420422441632462842483 FCC ID: 2AEEK-9005010029 IC: 20013-9005010029 CSA Group Bayern GmbH File No. T39444-00-01TK, page 5 of 30 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 2.6 Transmit operating modes The EUT uses GMSK modulation with a data rate of 250 kbps (kbps = kilobits per second) 2.7 Antenna The following antennas shall be used with the EUT: 2.8 Power supply system utilised Pow…

Text truncated - open the document above for the full version.

FCC ID: 2AEEK-9005010029 IC: 20013-9005010029 CSA Group Bayern GmbH File No. T39444-00-01TK, page 10 of 29 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 5 T E S T C O N D I T I O N S A N D R E S U L T S 5.1 AC power line conducted emissions For test instruments and accessories used see section 6 Part A4. 5.1.1 Description of the test location Test location: Shielded Room S2 5.1.2 Photo documentation of the test set-up 5.1.3 Applicable standard According to FCC Part 15, Section 15.207(a): Except as shown in paragraphs (b) and (c) of this Section, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed the given limits. 5.1.4 Description of Measurement The measurements are performed following the procedures set out in ANSI C63.4 described under item 4.4.3. If the minimum limit margin appears to be less than 20 dB with a peak mode measurement, the emissions are remeasured using a tuned receiver with quasi-peak and average detection and recorded on the data sheets. 5.1.5 Test result Frequency range: 0.15 MHz - 30 MHz Min. limit margin -15.9 dB at 0.323 MHz FCC ID: 2AEEK-9005010029 IC: 20013-9005010029 CSA Group Bayern GmbH File No. T39444-00-01TK, page 14 of 29 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 5.2 Field strength of fundamental For test instruments and accessories used see section 6 Part CPR3 . 5.2.1 Description of the test location Test location: Anechoic chamber 1 Test distance: 3 m 5.2.2 Photo documentation of the test set-up 5.2.1 Applicable standard According to FCC Part 15C, Section 15.249(a): The field strength of emissions from intentional radiators operated within these frequency bands shall comply with the effective limits. 5.2.2 Description of Measurement The radiated emission of the fundamental wave from the EUT is measured using a spectrum analyser and appropriate linear polarized antennas. The set up of the EUT and the measurement procedure is in accordance to ANSI C63.10, Item 6.5. The EUT is measured in TX continuous mode unmodulated under normal conditions. Analyser settings: Peak measurement: RBW: 1 MHz VBW: 1 MHz Detector: Max peak AV measurement: RBW: 1 MHz VBW: 10 Hz Detector: Max peak FCC ID: 2AEEK-9005010029 IC: 20013-9005010029 CSA Group Bayern GmbH File No. T39444-00-01TK, page 16 of 29 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 5.3 Out-of-band emission, radiated For test instruments and accessories used see section 6 Part SER 2, SER 3. 5.3.1 Description of the test location Test location: OATS 1 Test location: Anechoic chamber 2 Test distance: 3 m 5.3.2 Photo documentation of the test set-up Test setup 30 MHz – 1000 MHz: Test setup 1 GHz – 18 GHz: FCC ID: 2AEEK-9005010029 IC: 20013-9005010029 CSA Group Bayern GmbH File No. T39444-00-01TK, page 23 of 29 Ohmstrasse 1-4  94342 STRASSKIRCHEN  GERMANY Tel.: +49(0)9424-94810  Fax: +49(0)9424-9481440 Rev. No. 4.0, 2015-04-17 5.4 EBW and OBW For test instruments and accessories used see section 6 Part MB. 5.4.1 Description of the test location Test location: AREA4 5.4.2 Photo documentation of the test set-up 5.4.3 Applicable standard According to FCC Part 15, Section 15.215(c): Intentional radiators operating under the alternative provisions to the general emission limits, as contained in Section 15.217 through Section 15.257, must be designed to ensure that the 20 dB bandwidth of the emission is contained within the frequency band designated in the rule section under which the equipment is operated. 5.4.4 Description of Measurement The bandwidth is measured at an amplitude level reduced from the reference level by a specified ratio of -20 dB (99%). The x-dB-down (OBW) function of the analyser is used. The measurement is performed with normal modulation in TX continuous mode. Spectrum analyser settings: RBW: 30 kHz, VBW: 100 kHz, Span: 1.5 MHz, Trace mode: max. hold, Detector: max. peak; FCC ID: 2AEEK-9005010029 IC: 20013-9005010029 CSA Group Bayern G…

Text truncated - open the document above for the full version.