2AEL5PC-55-Channel Door Popper System Controller

5-Channel Door Popper System Controller Funcion Manual Work Voltage: 12V A output (-) , brown wire on the main unit When the main unit received the remote signal from button “1”, the main unit A output once negative for 1 second. B output (-) , blue wire on the main unit When the main unit received the remote signal from button “2”, the main unit, B output once negative for 1 second.. C output (-) , pink wire on the main unit When the main unit received the remote signal from button “3”, the main unit, C output once negative for 1 second.. D output (-) , orange wire on the main unit When the main unit received the remote signal from button “4”, the main unit, D output once negative for 1 second.. E output (-) , white wire on the main unit When the main unit received the remote signal from button “5”, the main unit, E output once negative for 1 second. . Main unit code learning Function : Press code learning button on the main unit for 3 seconds, LED will keep lighting, it means already enter into learning code status. If the main unit received any signal from the remote and the LED flash once. It shows the main unit code learning function programming successefully . 6. Safety Inhibit: Option On (default): When the ignition is on, there cannot be any output from the main unit system. When the ignition is off, the main unit system works normally. Option Off: There is output from the main unit system regardless of whether the ignition is on or off. 1).Enable this function on the main unit : When ACC is ON, keep pressing code learning button on the main unit for 5 times, the main unit LED function flash 3 times, then will enable the fafety inhibit output on the main unit . 2). Disable this function: When ACC is ON. keep pressing code learning button on the main unit for 4 times, the main unit LED flash 5 times, then will disable the fafety inhibit output on the main unit . Factory default safety inhibit option on the main unit is off . Factory default safety inhibit option off . Wiring Diagram FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the followingmeasures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (current) 4.0 5.0 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0 Digitel, LLC 2015.04.24 To: SIEMIC, Inc. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, Digitel, LLC hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): Product description: 5-Channel Door Popper System Controller model name: PC-5 FCC ID: 2AEL5PC-5 Sincerely, Client’s signature Client’s name / title : Winnie Schaffer / Manager Contact information / address: 2094 N Dragoon St, Tucson AZ,USA

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 4.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (obsolete) 2.0 3.0 Jan-31-2012 Added IC confidentiality letter form (current) 3.0 4.0 March-26-2015 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 4.0 Digitel, LLC 2015/4/24 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2AEL5PC-5 We hereby request confidential treatment of information accompanying this application as outlined below: - e.g. Block Diagram - e.g. Schematics - e.g. Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature Client’s signature Client’s name / title : Winnie Schaffer / Manager Contact information / address: 2094 N Dragoon St, Tucson AZ,USA

Shenzhen BCTC Technology Co., Ltd. FCC Report Tel: 400-788-9558 0755-33019988 Web:Http//www.bctc-lab.com Page1 of 5 APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Photo 1 Photo 2 Shenzhen BCTC Technology Co., Ltd. FCC Report Tel: 400-788-9558 0755-33019988 Web:Http//www.bctc-lab.com Page2 of 5 Photo 3 Photo 4 Shenzhen BCTC Technology Co., Ltd. FCC Report Tel: 400-788-9558 0755-33019988 Web:Http//www.bctc-lab.com Page3 of 5 Photo 5 Photo 6

3.1*3.8cm

Shenzhen BCTC Technology Co., Ltd. FCC Report Tel: 400-788-9558 0755-33019988 Web:Http//www.bctc-lab.com Page4 of 5 Photo 7 Photo 8 433.92MHz RECEIVER ANT Shenzhen BCTC Technology Co., Ltd. FCC Report Tel: 400-788-9558 0755-33019988 Web:Http//www.bctc-lab.com Page5 of 5 Photo 10 Photo 9

Shenzhen BCTC Technology Co., Ltd. Report No.: BCTC-150403970 FCC Report Tel: 400-788-9558 0755-33019988 Web:Http//www.bctc-lab.com Page1 of 22 PART15B TEST REPORT Product Name: 5-Channel Door Popper System Controller Trademark: N/A FCC ID: 2AEL5 PC-5 Model Number: Digitel, LLC Prepared For : 2094 N Dragoon St, Tucson AZ USA Address : Shenzhen BCTC Technology Co., Ltd. Prepared By : A. Floor 3, 44 Building, Tanglang Industrial Park B, Taoyuan Street, Nanshan District, Shenzhen, China Test Date: Apr. 13 - Apr. 20, 2015 Date of Report : Apr. 20, 2015 Report No.: BCTC-150403970 Shenzhen BCTC Technology Co., Ltd. Report No.: BCTC-150403970 FCC Report Tel: 400-788-9558 0755-33019988 Web:Http//www.bctc-lab.com Page2 of 22 TABLE OF CONTENTS TEST REPORT DECLARATION .................................................................................................. 3 1. GENERAL INFORMATION ....................................................................................................... 4 1.1. Report information .................................................................................................................................. 4 1.2. Measurement Uncertainty ....................................................................................................................... 4 1.3. Test Facility ............................................................................................................................................. 4 1.4. Test Uncertainty ...................................................................................................................................... 4 2. PRODUCT DESCRIPTION ......................................................................................................... 5 2.1. EUT Description ..................................................................................................................................... 5 2.2. Block Diagram of EUT Configuration .................................................................................................... 5 2.3. Test Conditions ....................................................................................................................................... 5 3. TEST RESULTS SUMMARY ..................................................................................................... 6 4. TEST EQUIPMENT USED .......................................................................................................... 7 4.1. For Conducted Emission Test ................................................................................................................. 7 4.2. For Radiated Emission Measurement ..................................................................................................... 7 5. CONDUCTED EMISSION TEST ............................................................................................... 8 5.1. Block Diagram of Test Setup .................................................................................................................. 8 5.2. Test Standard ........................................................................................................................................... 8 5.3. Conducted Emission Limit (Class B) ...................................................................................................... 8 5.4. EUT Configuration on Test ..................................................................................................................... 8 5.5. Operating Condition of EUT ................................................................................................................... 8 5.6. Test Procedure ......................................................................................................................................... 9 5.7. Test Result ............................................................................................................................................... 9 6. RADIATED EMISSION MEASUREMENT ............................................................................ 10 6.1. Block Diagram of Test Setup ................................................................................................................ 10 6.2. Test Standard ......................................................................................................................................... 11 6.3. Radiated Emission Limit(Class B) ........................................................................................................ 11 6.4. EUT Configuration on Test ................................................................................................................... 12 6.5. Test Procedure ....................................................................................................................................... 12 6.6. Test Result ............................................................................................................................................. 12 APPENDIX I (PHOTOS OF THE EUT) ...................................................................................... 17 APPENDIX II (TEST PHOTOS OF THE EUT) ......................................................................... 21 Shenzhen BCTC Technology Co., Ltd. Report No.: BCTC-150403970 FCC Report Tel: 400-788-9558 0755-33019988 Web:Http//www.bctc-lab.com Page3 of 22 TEST REPORT DECLARATION Applicant : Digitel, LLC Address : 2094 N Dragoon St, Tucson AZ USA EUT Description : 5-Channel Door Popper System Controller Model Number : PC-5 Operation Frequency: 433.92MHz(Only receiver) Test Standards: FCC Part 15 B: 2014 ANSI C63.4: 2014 The EUT described above is tested by US to determine the maximum emission levels emanating from the EUT, the maximum emission levels are compared to the FCC Part 15 B Subpart Class B limits. The measurement results are contained in this test report and Shenzhen BCTC Technology Co., Ltd. is assumed of full responsibility for the accuracy…

Text truncated - open the document above for the full version.