2AEN5-NASUrbanista Nashville Bluetooth Speaker

FCC COMPLIANCE This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, inclu- ding interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter- ference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the in- structions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televi- sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver. • Connect the equipment in to an outlet on a ci r cui t different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by Urbanista AB could void the user’s authori- ty to operate this equipment. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC ID: 2AEN5-NAS ICED CANADA This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the followingt two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause unde- sired operation of the device. Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio exempt de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’ en compromettre le fonctionnement. CAN ICES-3(B) /NMB-3(B) IC: 26612-NAS Bluetooth ® frequency band of operation 2402-2480MHz MHz • Bluetooth: Maximum transmit power less than 4.77 dBm EIRP EU/UK COMPLIANCE Urbanista AB hereby declares that this wireless device is in compliance with Direc tive 2014/53/EU and Radio Equipment Regulations 2017. A copy of the Declaration of Conformity is available at www.urbanista. com/compliance. Urbanista AB déclare par la présente que cet appareil sans fil est conforme aux exigences stipulées dans la Directive européenne 2014/53/EU et la réglementation britannique Radio Equipment Regulations 2017. Une copie de la Déclaration de conformité est disponible àl’adresse www.urbanista.com/ compliance. Hiermit erklärt Urbanista AB, dass sich dieses drahtlose Gerät in Ubereinstimmung mit der Richtlinie 2014/53/EU und den Regelungen über Funkanlagen von 2017 befindet. Eine Kopie der Konformitätserklärung ist her ver- fügbar www.urbanista.com/compliance. EU importer: Strax GmbH, Belgische Allee 52 - 54, 53842 Troisdorf Battery information Your device has an internal, non-removable, rechargeable battery. Do not attempt to remove the battery, as you may damage the device. The battery can be charged and discharged hundreds of times, but it will eventually wear out. Charging time can vary depending on device capability. Battery safety If left unused, a fully charged battery will lose its charge over time. Always keep the battery between -10°C and 40°C (14°F and 104°F) for optimal performance. Extreme temperatures reduce the capacity and lifeti- me of the battery. A device may temporarily stop working if its battery is too hot or too cold. Do not dispose of batteries in a fire as they may explode. Obey local regulations. Recycle when po ssible. Do not dispose of as household waste. Use the battery for its intended purpose only. Improper use of, or use of unapproved or incompatible, batteries may present a risk of fire explosion, or other hazards, and may invalidate any approval or warranty. If you believe the battery is damaged, take it to a service center or your local shop before continuing to use it. Never use a damaged battery. Do not charge your device during a lightning storm. DON’T attempt to remove the rechargeable lithium-ion battery from this product. Contact your local Urbanista retailer or other qualified professional for removal. Please dispose of used batteries properly, following local regulations. Disposal and recycling Information The symbol above means that according to local laws and regulations your product and/ or its battery shall be disposed of separately from household waste. When this product reaches its end of life, take it to a collection point designated by local authorities. The separate collection and recycling of your product and/or its battery at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. Informations sur la mise au rebut et le recyclage Le symbole ci-dessus signifie que, confor- mément aux lois et réglementations locales, vous devez mettre au rebut votre produit et/ou sa batterie sépar ément des ordures ménagères. Lorsque ce produit n’est plus utili- sable, déposez-le dans un centre de collecte des déchets agréé par les autorités locales. La collecte et le recyclage séparés de votre produit et/ou de sa batterie lors de ’élimina- tion contribuent à préserver les resources naturelles et à protéger l’environnement et la santé des êtres humans. Informationen zur entsorgung und zum recycling Das Symbol oben bedeutet, dass dieses Produkt und/oder die Batterie entsprechend den gelte…

Text truncated - open the document above for the full version.

Reference No.: WTX22X11232661W001 Page 2 of 13 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EXHIBIT 2 - EUT EXTERNAL PHOTOGRAPHS EUT View 1 EUT View 2 Reference No.: WTX22X11232661W001 Page 3 of 13 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EUT View 3 EUT View 4 Reference No.: WTX22X11232661W001 Page 4 of 13 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EUT View 5 EUT View 6 Reference No.: WTX22X11232661W001 Page 5 of 13 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EUT View 7 EUT View 8

Reference No.: WTX22X11232661W001 Page 1 of 13 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format FCC ID: 2AEN5-NAS Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the device’s expected lifetime. Proposed Label Location on EUT FCC ID Label Location

Reference No.: WTX22X11232661W001 Page 6 of 13 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EXHIBIT 3 - EUT INTERNAL PHOTOGRAPHS EUT Housing and Board View 1 EUT Housing and Board View 2 Reference No.: WTX22X11232661W001 Page 7 of 13 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EUT Housing and Board View 3 EUT Housing and Board View 4 Reference No.: WTX22X11232661W001 Page 8 of 13 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Solder Board-Component View 1 Solder Board-Component View 2 Reference No.: WTX22X11232661W001 Page 9 of 13 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Solder Board-Component View 3 Solder Board-Component View 4

Reference No.: WTX22X11232661W001 Page 10 of 13 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Solder Board-Component View 5 Antenna View

1. RF Exposure Requirements 1.1 General Information Client Information Applicant: Urbanista AB Address of applicant: Master Samuelsgatan 10, 1 Tr, Stockholm, Sweden Manufacturer: Urbanista AB Address of manufacturer: Master Samuelsgatan 10, 1 Tr, Stockholm, Sweden General Description of EUT: Product Name: Urbanista Nashville Bluetooth Speaker Trade Name / Model No.: Urbanista Nashville Adding Model(s): / Rated Voltage: DC3.7V Battery Capacity: 4000mAh FCC ID: 2AEN5-NAS Equipment Type: Mobile device Technical Characteristics of EUT: Bluetooth Bluetooth Version: V5.3 (BR/EDR mode) Frequency Range: 2402-2480MHz RF Output Power: 0.96dBm (Conducted) Data Rate: 1Mbps, 2Mbps Modulation: GFSK, π/4 DQPSK Quantity of Channels: 79 Channel Separation: 1MHz Type of Antenna: FPC Antenna Antenna Gain: 1.35dBi 1.2 RF Exposure Exemption According to §1.1307(b)(3) and 447498 D04 Interim General RF Exposure Guidance v01, system operating under the provisions of this section shall be operating in a manner that the public is not exposed to radio frequency energy level in excess limit for maximum permissible exposure. Option A: FCC Rule Part 1.1307 (b)(3)(i)(A):The available maximum time-averaged power is no more than 1mW, regardless of separation distance. Option B: FCC Rule Part 1.1307 (b)(3)(i)(B): The available maximum time-averaged power or effective radiated power (ERP), whichever is greater, is less than or equal to the threshold P th (mW) described in the following formula. P th is given by: Option C: FCC Rule Part 1.1307 (b)(3)(i)(C): The minimum separation distance (R in meters) from the body of a nearby person for the frequency (f in MHz) at which the source operates, the ERP (watts) is no more than the calculated value prescribed for that frequency. R must be at least λ/2π, where λ is the free-space operating wavelength in meters. Single RF Sources Subject to Routine Environmental Evaluation RF Source frequency (MHz) Threshold ERP (watts) 0.3-1.34 1,920 R 2 1.34-30 3,450 R 2 /f 2 30-300 3.83 R 2 300-1,500 0.0128 R 2 f 1,500-100,000 19.2R 2 For Multiple RF sources: FCC Rule Part 1.1307(b)(3)(ii): (A) The available maximum time-averaged power of each source is no more than 1 mW and there is a separation distance of two centimeters between any portion of a radiating structure operating and the nearest portion of any other radiating structure in the same device, except if the sum of multiple sources is less than 1 mW during the time-averaging period, in which case they may be treated as a single source (separation is not required). (B) In the case of fixed RF sources operating in the same time-averaging period, or of multiple mobile or portable RF sources within a device operating in the same time averaging period, if the sum of the fractional contributions to the applicable thresholds is less than or equal to 1 as indicated in the following equation. 1.3 Calculated Result Radio Access Technology Min. Frequency Max. Output Power Max. Tune-Up Output Power Antenna Gain Duty Cycle Tune-Up EIRP (MHz) (dBm) (dBm) (dBi) (%) (dBm) Bluetooth 2402 0.96 / 1.35 100 4.77 Frequency Option Min. Distance Tune-Up ERP Exposure Limit Ratio Result (MHz) (cm) (dBm) (mW) (mW) Pass/Fail 2441 B 0.5 2.62 1.83 2.76 0.66 Pass Note: 1. ERP=EIRP-2.15dB; EIRP= Output Power + Antenna gain 2. Option A, B and C refers as clause 1.2. 3. For option B, Pth(mW) convert to Exposure Limit(mW); For option C, ERP(W) convert to Exposure Limit(mW). 4. Ratio= Tune-Up ERP(mW)/ Exposure Limit (mW) Mode for Simultaneous Multi-band Transmission: Radio Access Technology Ratio 1 Ratio 2 Simultaneous Ratio Limit Result Pass/Fail -- -- -- -- -- -- Result: Pass

1 ShenZhen City FeiMin Technology CO.,LTD. SPECIFICATION FOR APPROVED CUSTOMER: Hunan Qiande Industry Co., Ltd PRODUCTS: Built-in 2.4G antenna PART NO: Spec.: FM-S2249-2064 -BT Data: 2022.10.21 REMARK:Please send us one(or copy)of this approval with stamp after accepting,other copies filed by the customer. ADD:Room 303,Building C,Hengnan one Road,Gushu community,Xixiang Street,Bao’an District,Shenzhen City Tel: 0755-23035723 Fax: 0755-23036702 E-mail: [email protected] HTTP:www.fmant.cn CUSTOMER ACCEPTED BY CHECKED BY APPROVED BY SUPPLIER PREPARED BY CHECKED BY APPROVED BY YangXuan Xia Xingxi Ma Doggdong SHENZHEN FEIMIN TECHNOLOGY CO.,LTD. 深圳市飞敏科技有限公司 Shenzhen Feimin Technology Co.,Ltd 2 Table of contents 1.Project Information ................................................................................... 4 1.1. Appearance and Dimensions ............................................................ 4 2. Electrical Characteristics .......................................................................... 5 2.1. Test Environment Conditions ........................................................... 5 2.2. Measurement method ....................................................................... 5 2.2.1. VSWR .......................................................................................... 5 2.2.2. Log Mag ...................................................................................... 6 2.3. Efficiency and Gain ....................................................................... 6 2.3.1. Test system .................................................................................. 6 2.3.2. No-source test data ...................................................................... 7 2.3.3. Antenna Radiation Pattern .......................................................... 7 3. Notes ......................................................................................................... 8 4.Product packaging specification ............................................................... 8 SHENZHEN FEIMIN TECHNOLOGY CO.,LTD. 深圳市飞敏科技有限公司 Shenzhen Feimin Technology Co.,Ltd 3 Revision history Version date state A1 2022-10-21 First edition change content： First change： Before the change：（If necessary, please add the corresponding picture, the change details should be clearly described here） After the change：（If necessary, please add the corresponding picture, the change details should be clearly described here） ANTENNA SPECIFICATION 深圳市飞敏科技有限公司 Shenzhen Feimin Technology Co.,Ltd 4 1.Project Information 1.1. Appearance and Dimensions ANTENNA SPECIFICATION 深圳市飞敏科技有限公司 Shenzhen Feimin Technology Co.,Ltd 5 2.Electrical Characteristics 2.1. Test Environment Conditions Temperature Ordinary Temperature (5 to 35°C) Humidity Ordinary Humidity (25 to 85% RH) 2.2. Measurement method 2.2.1. VSWR ANTENNA SPECIFICATION 深圳市飞敏科技有限公司 Shenzhen Feimin Technology Co.,Ltd 6 2.2.2. Log Mag 2.3. Efficiency and Gain 2.3.1. Test system ANTENNA SPECIFICATION 深圳市飞敏科技有限公司 Shenzhen Feimin Technology Co.,Ltd 7 2.3.2. No-source test data Frequency (MHz) Gain (dBi) Efficiency (%) 2400 MHz 1.07 37.2 2410 MHz 1.11 38.57 2420 MHz 1.25 39.66 2430 MHz 1.13 38.89 2440 MHz 1.26 39.03 2450 MHz 1.35 40.94 2460 MHz 1.33 40.79 2470 MHz 1.27 39.33 2480 MHz 1.18 38.55 2490 MHz 1.15 38.36 2500 MHz 1.22 39.58 2.3.3. Antenna Radiation Pattern XOY-plane@2450MHz YOZ-plane@2450MHz XOZ-plane@2450MHz 3D-plane @2450MHz ANTENNA SPECIFICATION 深圳市飞敏科技有限公司 Shenzhen Feimin Technology Co.,Ltd 8 3.Notes 1、Be careful not to be too close to the metal part during installation to avoid affecting the antenna performance. 2 、This antenna is only suitable for this model. The position of the antenna cannot be changed at will. If it is used on other machines, the effect will deteriorate, which has nothing to do with our company. 4.Product packaging specification product name: 2.4G antenna Antenna form：FPC+shielded wire 1、Labeling requirements The inner label is 7CM long and 4CM wide The outer label is 7CM long, about 5CM 2、Packing process Job description： 1.The product __PCS is packed in PE open pockets, and the inner label is affixed to each pouch; Put the __ small bag into the big PE sealing tape bag, except the tail number and spare parts. 2.Each box contains __ large bags of products, and the boxes are sealed with adhesive tape in the shape of "I"。 3.Paste the outer label on the upper right corner of the box, and there must be no missing or wrong filling. 3、Precautions When packing the box, please pay attention to lay the antenna flat and avoid serious shaking after sealing. If the whole box is not filled, it needs to be filled with foam to avoid transportation Circumstances that caused product defects in the process。 client's name supplier Shenzhen Feimin Technology Co., Ltd. Order number ************* Material coding ************* Specification model ****** product name ******* quantity *****PCS QC: spare parts ***PCS Notes supplier Shenzhen Feimin Technology Co., Ltd. product name *********** Material coding *********** Specifications ********** quantity ***PCS product

Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 1 of 61 TEST REPORT Reference No. .................... : WTX22X11232661W001 FCC ID ................................ : 2AEN5-NAS Applicant ........................... : Urbanista AB Address.............................. : Master Samuelsgatan 10, 1 Tr, Stockholm, Sweden Manufacturer ..................... : The same as Applicant Address.............................. : The same as Applicant Product Name ................... : Urbanista Nashville Bluetooth Speaker Model No... ......................... : Urbanista Nashville Standards .......................... : FCC Part 15.247 Date of Receipt sample .... : 2022-11-18 Date of Test........................ : 2022-11-18 to 2022-12-05 Date of Issue ..................... : 2022-12-05 Test Report Form No. ....... : WTX_Part 15_247W Test Result ......................... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of approver. Prepared By: Waltek Testing Group (Shenzhen) Co., Ltd. Address: 1/F., Room 101, Building 1, Hongwei Industrial Park, Liuxian 2nd Road, Block 70 Bao'an District, Shenzhen, Guangdong, China Tel.: +86-755-33663308 Fax.: +86-755-33663309 Email: [email protected] Tested by: Approved by: Gala Wang Silin Chen Reference No.: WTX22X11232661W001 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 2 of 61 TABLE OF CONTENTS 1. GENERAL INFORMATION ...................................................................................................................................5 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .........................................................................5 1.2 TEST STANDARDS .................................................................................................................................................6 1.3 TEST METHODOLOGY ...........................................................................................................................................6 1.4 TEST FACILITY ......................................................................................................................................................6 1.5 EUT SETUP AND TEST MODE ..............................................................................................................................7 1.6 MEASUREMENT UNCERTAINTY .............................................................................................................................9 1.7 TEST EQUIPMENT LIST AND DETAILS ................................................................................................................. 10 2. SUMMARY OF TEST RESULTS ......................................................................................................................... 13 3. ANTENNA REQUIREMENT ................................................................................................................................ 14 3.1 STANDARD APPLICABLE ..................................................................................................................................... 14 3.2 EVALUATION INFORMATION ................................................................................................................................ 14 4. FREQUENCY HOPPING SYSTEM REQUIREMENTS.................................................................................... 15 4.1 STANDARD APPLICABLE ..................................................................................................................................... 15 4.2 FREQUENCY HOPPING SYSTEM ......................................................................................................................... 15 4.3 EUT PSEUDORANDOM FREQUENCY HOPPING SEQUENCE ............................................................................... 16 5. QUANTITY OF HOPPING CHANNELS AND CHANNEL SEPARATION ................................................... 17 5.1 STANDARD APPLICABLE ..................................................................................................................................... 17 5.2 TEST SETUP BLOCK DIAGRAM ........................................................................................................................... 17 5.3 TEST PROCEDURE .............................................................................................................................................. 17 5.4 SUMMARY OF TEST RESULTS/PLOTS ................................................................................................................. 18 6. DWELL TIME OF HOPPING CHANNEL .......................................................................................................... 19 6.1 STANDARD APPLICABLE ..................................................................................................................................... 19 6.2 TEST SETUP BLOCK DIAGRAM ........................................................................................................................... 19 6.3 TEST PROCEDURE .............................................................................................................................................. 19 6.4 SUMMARY OF TEST RESULTS/PLOTS ................................................................................................................. 20 7. 20DB BANDWIDTH ............................................................................................................................................... 21 7.1 STANDARD APPLICABLE ..................................................................................................................................... 21 7.2 TEST SETUP BLOCK DIAGRAM ........................................................…

Text truncated - open the document above for the full version.

Reference No.: WTX22X11232661W001 Page 11 of 13 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn EXHIBIT 4 - TEST SETUP PHOTOGRAPHS Conducted Emission Test Setup Radiation Emission Test Setup (Below 30MHz) Reference No.: WTX22X11232661W001 Page 12 of 13 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Radiation Emission Test Setup (30MHz to 1GHz) Radiation Emission Test Setup (1GHz to 18GHz) Reference No.: WTX22X11232661W001 Page 13 of 13 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Radiation Emission Test Setup (Above 18GHz) ***** END OF REPORT *****