2AEQM-KATALYSTMobile Booster

1 5 Band WIRELESS 4G/LTE Consumer Mobile 50dB Booster USER MANUAL Model # Katalyst FCC ID: 2AEQM-KATALYST IC: 20195-KATALYST 2 KIKA KATALYST WIRELESS 4G/LTE BOOSTER Instruction Guide Table of Contents 2 Warnings 2 Placement of your Kika Katalyst Wireless Mobile Booster 3 The Inside Panel Antenna 4 The Outside Window Mount Antenna 5 Connecting the Kika Katalyst Wireless Mobile Booster 6 Your Warranty 7 Technical Specifications 8 3 THIS IS A CONSUMER DEVICE BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by Kika M2M. Antennas MUST be installed at least 20cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider. WARNING: E911 location information may not be provided or may be inaccurate for calls served by using this device. You are cautioned that changes or modifications not expressly approved by the FCC will void your authority to operate the equipment and will void your warranty. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference(2) this device must accept any interference received, including interference that may cause undesired operation. No antennas can be used with this Booster that is not listed within this manual. Using Non Approved antennas will violate FCC regulations, and will result in your warranty being voided. 4 PLACEMENT OF YOUR KIKA KATALYST WIRELESS MOBILE 4G/LTE BOOSTER It is strongly suggested that you follow the instructions in this guide to obtain the best performance of your device. Fail- ing to do so could result in causing a disturbance to the network you are using and the booster shutting off until the problem has been rectified. Select a location for the Booster placement, making sure you pick a spot with good ventilation and no moisture will come in contact with your Kika Katalyst Wireless Mobile 4G/LTE Booster. When deciding where to put your new Kika Katalyst Wireless Mobile 4G/LTE Booster, you must take into ac- count the cable lengths of your two antennas (Exterior Window Mount Antenna (12 feet), Interior Panel Antenna (10 feet), and your power supply cable (4 feet) must be able to reach the spot you have decided to place your new Kika Katalyst Wireless Mobile 4G/LTE Booster. This will avoid having problems after your installation (i.e. improp- er placement, cable extension problems etc.), and cause problems with a network provider or FCC regulations thus causing the Kika Katalyst Wireless Mobile 4G/LTE Booster to shut off. Network signals are sent and received by the cell tower and the wireless cellphone/device constantly passes though the Katalyst Wireless Mobile 4G/LTE Booster and back to the cell tower. The reason you purchased the Katalyst Wireless Mobile 4G/LTE Booster is the ability of your cellphone/device to constantly connect to a cell tower. When you are in a mobile vehicle the signal from the cell tower is often inconsistent and the Katalyst Wire- less Mobile 4G/LTE Booster will find the cell tower and transmit the signal through the outdoor antenna back and forth through the Katalyst Wireless Mobile 4G/LTE Booster to the indoor antenna where up to eight users/devices can all have service inside their vehicle. THE USE OF NON KIKA M2M LISTED ANTENNAS, CABLES OR EXTEDING THE CABLE LENGTH IS NOT PERMITTED BY THE FCC AND CAUSE THE BOOSTER TO SHUT DOWN AND MAY DAMAGE THE BOOSTER AND COULD VOID YOUR WARRANTY. 5 INSTALLING THE INERNAL ANTENNA The Kika Katalyst Wireless Mobile 4G/LTE Booster requires two antennas with a vertical separation of at least of four feet and a minimum horizontal separation of Eight feet from the other antenna. The Inside Panel Antenna should not be installed any further than twelve feet from the Kika Wireless Mobile 4G/LTE Booster. The extension of any cables may cause problems with a network provider or FCC regulations thus causing the Kika Katalyst Wireless Mobile 4G/LTE Booster to shut off. Find an appropriate location in the vehicle such as in the glove compartment or on under the seat, between the front seats etc. Before making the placement permanent make sure the Inside Panel antenna cable can reach your Kika Katalyst Wireless Mobile 4G/LTE Booster. Run the Interior Panel Antenna cable to the Kika Katalyst Wireless Mobile 4G/LTE Booster. Never use any sharp ob- jects to secure the cable, and be careful not to pierce the outer cable casing because it will negatively affect how your Kika Katalyst Wireless Mobile 4G/LTE Booster works. Remove the adhesive backing of the Inside Panel Antenna making sure that that the adhesive side is facing the in- terior of the vehicle and then secure the Inside Panel Antenna to the inside of your glove compartment or the fire- wall of your vehicle, etc. Never use tools to secure your Kika Katalyst Wireless Mobile 4G/LTE Booster to the connector labeled INT-ANT, as you could damage the Booster and could void your warranty. THE USE OF NON KIKA M2M LISTED ANTENNAS, CABLES OR EXTEDING THE CABLE LENGTH IS NOT PERMITTED BY THE FCC AND CAUSE THE BOOSTER TO SHUT DOWN AND MAY DAMAGE THE BOOSTER AND COULD VOID YOUR WARRANTY. 6 INSTALLING Exterior Window Mount Antenna The Kika Katalyst Wireless Mobile 4G/LTE Booster utilizes antennas that require a vertical separation of at least of three feet and a minimum horizontal separation of five feet. The external window mount antenna MUST have a minimum of 180º degree line of sight with a minimum of eight inches above any obstruction. The external window mount antenna should not be installed any further than twelve feet from the Kika Katalyst Wireless Booster Wi…

Text truncated - open the document above for the full version.

Kika M2M LLC. 4050 ne 6th ave, Oakland Park, FL 33334 www.kikam2m.com 8003881160 May 19, 2015 Compliance Testing, LLC 1724 S. Nevada Way Mesa, AZ 85204 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Diana Williams and Compliance Testing, LLC to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug use Act of 1988, 21 U.S.C.853(a). Regards, Ricardo Salguero Ricardo Salguero President / Chief Discovery Officer Kika M2M [email protected]

Kika M2M LLC. 4050 ne 6th ave, Oakland Park, FL 33334 www.kikam2m.com 8003881160 May 19, 2015 Attestation For Kika M2M: FCC ID: 2AEQM-KATALYST To whom it may concern, The following statements are accurate Each Signal Booster certificated under FCC ID: 2AEQM-KATALYST is manufactured and each booster is ensured to be FCC compliant: (1) This consumer booster is not user programmable and does not require fine tuning or adjustments, or require professional installation. However, in a case the booster LED indicator light shows the need, the gain/power will self adjust as described in the User Manual. Such adjustments are built-in “failsafe”, guards as they will not allow the booster to be non-compliant to NPS compliance or safeguard requirements. (2) Future software upgrade will not cause non-compliance. (3) NPS and other compliance/safeguard features cannot be field reconfigured, disabled, or removed and does not require professional installation. (4) Licensee consent is not required for FCC certification equipment authorization purposes, but licensee consent does remain applicable per 20.21 provisions for both provider specific and wideband boosters. (5) NPS and other compliance/safeguard features have been implemented. (3) NPS and other compliance/safeguard features are defaulted to be “On” (in operation). Regards, Ricardo Salguero Ricardo Salguero President / Chief Discovery Officer Kika M2M [email protected]

Kika M2M LLC. 4050 ne 6th ave, Oakland Park, FL 33334 www.kikam2m.com 8003881160 LONG TERM CONFIDENTIALITY REQUEST LETTER 5/19/2015 Compliance Testing LLC 1724 S. Nevada Way Mesa, AZ 85204 RE: Long term confidentiality request for Kika Katalyst, FCC ID: 2AEQM-KATALYST To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the following documents required to be submitted with this application be permanently withheld from public review. ● Block Diagram ● Schematics ● Theory of Operation ● Parts List ● Tune Up Procedure These documents contain detailed system and equipment descriptions and related information about the product, which manufacturer/applicant considers to be proprietary, confidential, and a custom design and otherwise, would not release to the general public. Since this design is a basis from which future technological products will evolve, manufacturer/applicant feels that this information would be of benefit to its competitors, and that the disclosure of the information in these documents would give our competitors an unfair advantage in the market. Regards, Ricardo Salguero Ricardo Salguero President / Chief Discovery Officer Kika M2M [email protected]

Kika M2M LLC. 4050 ne 6th ave, Oakland Park, FL 33334 www.kikam2m.com 8003881160 Short Term Confidentiality Request Letter 5/19/2015 Compliance Testing LLC 1724 S. Nevada Way Mesa, AZ 85204 RE: Short Term Confidentiality Request For Kika Katalyst FCC ID: 2AEQM-KATALYST To Whom It May Concern: In accordance with sections 0.457 and 0.459 of CFR 47, Kika M2M. requests short-term Confidentiality of following sections of this application for a period of 180 days after grant is issued. • Test setup photos • External photos • Internal photos • User’s manual These documents contain detailed system and equipment descriptions and related information about the product, which manufacturer/applicant considers to be proprietary, confidential, and a custom design and otherwise, would not release to the general public. Since this design is a basis from which future technological products will evolve, manufacturer/applicant feels that this information would be of benefit to its competitors, and that the disclosure of the information in these documents would give our competitors an unfair advantage in the market. Grantee will not market or distribute product during the period requested. Once product is available for marketing, Grantee will notify FCC or TCB. Please contact me if there is any information you may need Regards, Ricardo Salguero Ricardo Salguero President / Chief Discovery Officer Kika M2M [email protected]

Kika M2M LLC. 4050 ne 6th ave, Oakland Park, FL 33334 www.kikam2m.com 8003881160 Mobile External Antenna Kitting Configurations Mobile Internal Antenna Kitting Configurations 1. EMM‐ 6321 Magnetic Mount w/12ft RG58 Cable 1. IBA ‐ 0321 Blade w/ 10ft RG 174 Cable 2. ELPN ‐ 5822 Low Profile w/ 12ft RG 174U Cable 2. IPA ‐ 0544 Patch w/10ft RG 174 Cable 3. EWM ‐ 4323 Window Mount w/10ft RG 58 Cable 3. ILPOA ‐ 1954 Low Profile Omni w/25ft RG 58 Cable 4. E4MM ‐ 6324 Magnetic Mount V2 w/12ft cable 4. IDC ‐7972 Direct Connect (no cable) 5. EHPMM ‐ 5856 HP Low Profile w/12ft RG174U Cable 5. IDA ‐ 9953 Dome Omni w/25ft RG 58 Cable 6. ETA ‐ 3162 Trucker w/ 10ft RG58 Cable 6. IDA2 ‐ 9969 Dome v2 Omni w/25ft RG 58 Cable 7. ESTA ‐ 3122 Trucker V2 W/15ft RG58 Cable 7. IPA ‐ 8734 Panel Directional w/ 50ft RG 58 8. FY9E – 7230S Uni Omni w/ 25ft RG 58 cable 8. IPA‐ 0544 Panel V2 Directional w/ 50ft RG 58 9. FY14E ‐ 7231 Uni Omni V2 w/ 25ft RG 58 cable 9. IDA ‐ 9953 Dome Omni w/ 25ft RG58 10. O32A ‐ 8882 Omni Directional w/ 25ft RG 58 cable 10. IDA2 ‐ 9969 Dome V2 Omni w/ 25ft RG58 11. O18A ‐ 8889 Omni Directional V2 w/ 25ftRG 58 cable 11. IDC ‐7972 Omni 12. O8A ‐ 8883 Omni Directional V3 w/ 25ft RG 58 cable Up‐Link Frequency Band (MHz) 698‐716 777‐787824‐849 1710‐1755 1850‐1915 MSCL Minimum (dB) 28.70 28.21 26.88 32.60 31.80 1.5' Separation Distance Path Loss (dB) 22.70 23.60 24.10 30.50 31.20 Polarity Loss 3.00 3.00 3.00 3.00 3.00 Max Antenna Gain Less Cable Loss (dB) ‐3.00 ‐1.61 0.22 0.90 2.40 Conducted Uplink Power Uplink Frequency (MHz) 698‐716 776‐787824‐849 1710‐1755 1850‐1915 Uplink Output Power (dBm) 26.51 25.57 25.25 25.64 25.32 Downlink Output Power (dBm) 14.90 15.24 15.44 16.01 11.65 Mobile External Kitting Configurations 1. EMM‐ 6321 Magnetic Mount w/12ft RG58 DS Cable Antenna Gain (dBI) 2.12 1.34 1.47 2.21 3.77 Coax Cable Loss (dB) 2.88 4.31 3.91 3.97 3.54 Final Antenna Gain less Loss (dB) ‐0.76 ‐2.97 ‐2.44 ‐1.76 0.23 Uplink Output Power EIRP (dBm) 25.75 22.60 22.81 23.88 25.55 Downlink Output Power EIRP (dBm) 14.14 12.27 13.00 14.25 11.88 2. ELPN ‐ 5822 Low Profile w/12 ft RG 58 DS Cable Antenna Gain (dBI) 1.23 1.54 1.77 2.56 3.99 Coax Cable Loss (dB) 2.71 4.21 3.77 3.61 3.93 Final Antenna Gain less Loss (dB) ‐1.48 ‐2.67 ‐2.00 ‐1.05 0.06 Uplink Output Power EIRP (dBm) 25.03 22.90 23.25 24.59 25.38 Downlink Output Power EIRP (dBm) 13.42 12.57 13.44 14.96 11.71 3. EWM ‐ 4323 Window Mount w/12ft RG 58 Cable Antenna Gain (dBI) 2.19 2.72 3.38 3.34 2.47 Coax Cable Loss (dB) 3.71 3.21 2.98 2.87 3.65 Kika M2M LLC. 4050 ne 6th ave, Oakland Park, FL 33334 www.kikam2m.com 8003881160 Final Antenna Gain less Loss (dB) ‐1.52 ‐0.49 0.40 0.47 ‐1.18 Uplink Output Power EIRP (dBm) 24.99 25.08 25.65 26.11 24.14 Downlink Output Power EIRP (dBm) 13.38 14.75 15.84 16.48 10.47 4. E4MM ‐ 6324 Magnetic Mount V2 w/12 ft RG 58 Cable Antenna Gain (dBI) 3.88 3.71 2.88 4.59 5.01 Coax Cable Loss (dB) 2.86 4.32 3.87 4.01 3.61 Final Antenna Gain less Loss (dB) 1.02 ‐0.61 ‐0.99 0.58 1.40 Uplink Output Power EIRP (dBm) 27.53 24.96 24.26 26.22 26.72 Downlink Output Power EIRP (dBm) 15.92 14.63 14.45 16.59 13.05 5. EHPMM ‐ 5856 HP Low Profile w/10 ft RG174 DS Cable Antenna Gain (dBI) 2.21 2.22 2.56 3.87 4.01 Coax Cable Loss (dB) 2.43 2.77 3.24 3.57 3.66 Final Antenna Gain less Loss (dB) ‐0.22 ‐0.55 ‐0.68 0.30 0.35 Uplink Output Power EIRP (dBm) 26.29 25.02 24.57 25.94 25.67 Downlink Output Power EIRP (dBm) 14.68 14.69 14.76 16.31 12.00 6. ETA ‐ 3162 Trucker Antenna w/ 12ft RG58 DS Cable Antenna Gain (dBI) 5.93 5.54 3.67 3.60 2.11 Coax Cable Loss (dB) 3.87 3.88 3.34 2.76 2.88 Final Gain less Loss (dB) 2.06 1.66 0.33 0.84 ‐0.77 Uplink Output Power EIRP (dBm) 28.57 27.23 25.58 26.48 24.55 Downlink Output Power EIRP (dBm) 16.96 16.90 15.77 16.85 10.88 7. ESTA ‐ 3122 Trucker V2 W/12ft RG58 DS Cable Antenna Gain (dBi) 3.13 3.99 3.92 2.88 3.09 Coax Cable Loss (dB) 3.78 3.32 3.67 4.39 3.34 Final Gain less Loss (dB) ‐0.65 0.67 0.25 ‐1.51 ‐0.25 Uplink Output Power EIRP (dBm) 25.86 26.24 25.5 24.13 25.07 Downlink Output Power EIRP (dBm) 14.25 15.91 15.69 14.50 11.40 Fixed External Kitting Configurations 1. FY9E ‐ 7230 Yagi Antenna w/ 50ft RG 58 cable Antenna Gain (dBI) 5.61 5.12 6.77 6.97 6.01 Coax Cable Loss (dB) 6.29 6.81 7.77 7.91 8.18 Kika M2M LLC. 4050 ne 6th ave, Oakland Park, FL 33334 www.kikam2m.com 8003881160 Final Gain less Loss (dB) ‐0.68 ‐1.69 ‐1.00 ‐0.94 ‐2.17 Uplink Output Power EIRP (dBm) 25.83 23.88 24.25 24.7 23.15 Downlink Output Power EIRP (dBm) 14.22 13.55 14.44 15.07 9.48 2. FY14E ‐ 7231 Yagi Antenna V2 w/ 25ft RG 58 cable Antenna Gain (dBI) 7.22 3.78 5.40 4.84 5.57 Coax Cable Loss (dB) 4.97 5.39 5.55 3.95 3.45 Final Gain less Loss (dB) 2.25 ‐1.61 ‐0.15 0.89 2.12 Uplink Output Power EIRP (dBm) 28.76 23.96 25.10 26.53 27.44 Downlink Output Power EIRP (dBm) 17.15 13.63 15.29 16.90 13.77 3. O32A ‐ 8882 Omni Antenna w/ 50ft RG 58 cable Antenna Gain (dBI) 3.88 4.62 3.96 5.04 5.98 Coax Cable Loss (dB) 6.29 6.81 7.77 7.91 8.18 Final Gain less Loss (dB) ‐2.41 ‐2.19 ‐3.81 ‐2.87 ‐2.2 Uplink Output Power EIRP (dBm) 24.1 23.38 21.44 22.77 23.12 Downlink Output Power EIRP (dBm) 12.49 13.05 11.63 13.14 9.45 4. O18A ‐ 8889 Omni Directional V2 w/ 25ftRG 58 cable Antenna Gain (dBI) 4.65 3.63 4.87 3.04 3.92 Coax Cable Loss (dB) 4.97 5.23 4.48 3.89 3.45 Final Gain less Loss (dB) ‐0.32 ‐1.60 0.39 ‐0.85 0.47 Uplink Output Power EIRP (dBm) 26.19 23.97 25.64 24.79 25.79 Downlink Output Power EIRP (dBm) 14.58 13.64 15.83 15.16 12.12 5. O8A ‐ 8883 Omn Directional V3 w/ 25ft RG 58 cable Antenna Gain (dBI) 2.65 2.21 2.89 2.04 3.07 Coax Cable Loss (dB) 4.97 4.03 3.77 3.89 3.45 Final Gain less Loss (dB) ‐2.32 ‐1.82 ‐0.88 ‐1.85 ‐0.38 Uplink Output Power EIRP (dBm) 24.19 23.75 24.37 23.79 24.94 Downlink Output Power EIRP (dBm) 12.58 13.42 14.56 14.16 11.27 Mobile Internal Kitting Configurations 1. IBA0321 Blade w/ 10ft RG 174 Cable Antenna Gain (dBI) 1.56 2.62 1.77 2.33 2.87 Coax Cable Loss (dB) 4.73 4.39 3.87 3.91 4.01 Final Gain less Loss (dB) ‐3.…

Text truncated - open the document above for the full version.

THIS IS A CONSUMER DEVICE BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 in) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed service provider. WARNING: E911 location information may not be provided or may be inaccurate for calls served using this device. Frequency Bands 698-716 MHz / 728 -746 MHz / 776-787 MHz / 746- 757 MHz/ 824-949 MHz 869 - 894 MHz / 1850 - 1910 MHz / 1930 - 1990 MHz / 1710 - 1755MHz 2110 -2155 MHz FCC ID: 2AEQM-KATALYST IC: 20195-KATALYST Model # KATALYST USA Made

p1550022_FCC_Part 20_Rev 1.0 Page 1 of 141 Test Report Prepared for: Kika M2M LLC Model: KIKA KATALYST Description: Wireless 4G/LTE Booster FCC ID: 2AEQM-KATALYST To FCC Part 20 Date of Issue: May 29, 2015 On the behalf of the applicant: Kika M2M LLC 4050 NE 6 th Ave Oakland Park, FL 33334 Attention of: Ricardo Salguero, President/Chief Discovery Officer Ph: (800) 388-1160 E-Mail: [email protected] Prepared By Compliance Testing, LLC 1724 S. Nevada Way Mesa, AZ 85204 (480) 926-3100 phone / (480) 926-3598 fax www.compliancetesting.com Project No: p1550022 Mike Graffeo Project Test Engineer This report may not be reproduced, except in full, without written permission from Compliance Testing. All results contained herein relate only to the sample tested. p1550022_FCC_Part 20_Rev 1.0 Page 2 of 141 Test Report Revision History Revision Date Revised By Reason for Revision 1.0 February 20, 2015 Mike Graffeo Original Document p1550022_FCC_Part 20_Rev 1.0 Page 3 of 141 Table of Contents Description Page Standard Test Conditions and Engineering Practices 5 Test Result Summary 6 Authorized Frequency Band 7 Maximum Power and Gain 13 Intermodulation 16 Out-of-Band Emissions 22 Conducted Spurious Emissions 53 Noise Limits 76 Uplink Inactivity 83 Variable Gain 84 Occupied Bandwidth 90 Oscillation Detection 121 Radiated Spurious 138 Test Equipment Utilized 141 p1550022_FCC_Part 20_Rev 1.0 Page 4 of 141 ILAC / A2LA Compliance Testing, LLC, has been accredited in accordance with the recognized International Standard ISO/IEC 17025:2005. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to the joint ISO-ILAC-IAF Communiqué dated January 2009). The tests results contained within this test report all fall within our scope of accreditation, unless noted below. Please refer to http://www.compliancetesting.com/labscope.html for current scope of accreditation. Testing Certificate Number: 2152.01 FCC Site Reg. #349717 IC Site Reg. #2044A-2 Non-accredited tests contained in this report: N/A p1550022_FCC_Part 20_Rev 1.0 Page 5 of 141 Test and Measurement Data Sub-part 2.1033(c)(14): All tests and measurement data shown were performed in accordance with FCC Rules and Regulations, Part 2, Subpart J and the following individual Parts: 20.21 in conjunction with latest version of KDB 935210. Standard Test Conditions and Engineering Practices Except as noted herein, the following conditions and procedures were observed during the testing: In accordance with ANSI/C63.4-2009, and unless otherwise indicated in the specific measurement results, the ambient temperature of the actual EUT was maintained within the range of 10° to 40°C (50° to 104°F), unless the particular equipment requirements specified testing over a different temperature range. Also, unless otherwise indicated, the humidity levels were in the range of 10% to 90% relative humidity. Environmental Conditions Temp (ºC) Humidity (%) Pressure (mbar) 24.9 – 31.0 33.5 – 63.0 985.5 - 943.0 Measurement results, unless otherwise noted, are worst-case measurements. EUT Description Model: KIKA KATALYST Description: Wireless 4G/LTE Booster Firmware: N/A Software: N/A Accessories: Power adaptor supplied from customer Serial Number: N/A Additional Information: The EUT is a Mobile, bi-directional amplifier for the boosting of cellular phone signals and data communication devices. The following frequency bands and emission types are utilized. Special test modes were utilized at times Frequency Band (MHz) Uplink 698 - 716 776 - 787 824 - 849 1850 – 1910 1710 – 1755 Downlink 728 - 746 746 - 757 869 - 894 1930 - 1990 2110 - 2155 Modulation Type LTE GSM, CDMA, EDGE, HSPA. EVDO, LTE CDMA, HSPA, LTE, EDGE, EVDO Emission Designators CDMA HSPA LTE EVDO EDGE GSM F9W F9W G7D F9W G7W GXW The modulation types and emission designators listed in the tables represent the modulations that the cell phone providers use for each frequency band. GSM, CDMA, and WCDMA represent all the modulation types (phase and amplitude or a combination thereof) utilized within the industry. EDGE, HSPA, LTE etc. are all protocols or multiplexing techniques using the base modulations. EUT Operation during Tests The EUT was in a normal operating condition. p1550022_FCC_Part 20_Rev 1.0 Page 6 of 141 Test Result Summary Specification Test Name Pass, Fail, N/A Comments 20.21(e)(3) Authorized Frequency Band Pass 20.21(e)(8)(i)(B) 20.21(e)(8)(i)(C) 20.21(e)(8)(i)(D) Maximum Power and Gain Pass 20.21(e)(8)(i)(F) Intermodulation Pass 20.21(e)(8)(i)(E) Out-of-Band Emissions Pass 2.1051 22.917(a) 24.238((a) Conducted Spurious Emissions Pass 20.21(e)(8)(i)(A) 20.21(e)(8)(I) Noise Limits N/A Per the test data on page 32, the noise is below - 70dBm/MHz (“Transmit Power OFF Mode”) therefore is by default compliant to the Variable Uplink Noise Power Tests, Variable Downlink Noise Power Tests, and Noise timing tests. These tests are not applicable. 20.21(e)(8)(i)(I) Uplink Inactivity N/A per rule 20.21e... if noise is less than -70dBm/MHz (“Transmit Power OFF Mode”) then EUT will not shut off, therefore this test will not be performed 20.21(e)(8)(i)(C)(1) 20.21(e)(8)(i)(C)(H) 20.21(e)(8)(i)(C)(2)(iii)(mobile) Variable Gain Pass 2.1049 Occupied Bandwidth Pass 20.21(e)(8)(ii)(A) Oscillation Detection Pass 2.1053 Radiated Spurious Pass 20.21(e)(8)(i)(B) Spectrum Block Filtering N/A This only applies to devices utilizing spectrum block filtering p1550022_FCC_Part 20_Rev 1.0 Page 7 of 141 Authorized Frequency Band Engineer: Mike Graffeo Test Date: 2/16/15 Test Procedure The EUT was connected to a spectrum analyzer through an attenuator with the losses being input into the spectrum analyzer as a combination of reference level offset and correction factor as needed to ensure accurate readings. A signal generator was utilized to produce a CW input signal tuned to the center channel of the operational band. The RF input level was increased…

Text truncated - open the document above for the full version.

Test Setup Photos FCC ID: AEQM-KATALYST IC: 20195-KATALYST RF Conducted Test Setup Photos FCC ID: AEQM-KATALYST IC: 20195-KATALYST RF Radiated #1 (Frequencies < 1GHz) Test Setup Photos FCC ID: AEQM-KATALYST IC: 20195-KATALYST RF Radiated #2 (Frequencies > 1GHz)