2AF2NDNS360LBMultifunction Sensor

72 mm (2.83 in) 63 mm (2.48 in) 41 mm (1.61 in) 39 mm (1.54 in) Installation Instructions DNS360CCA 2 120° IEC Pollution Degree II PIRPIR 2.1 - 4.0 m (6.9 - 13.1 ft) 7 m (23 ft)* 2.4 m (7.9 ft)* 5.5 m (18 ft)* 25 ̊ C (77 ̊ F)* > 2 m (6.5 ft) 1A1B DNS360LB-CR-PIR-DYNET DNS360LB-CR-PIR-DYNET-RAL9005 Installation Instructions Instructions d’installation Installationsanweisungen Instrucciones de instalación Istruzioni per l’installazione Installatie-instructies インストール手順 安装指南 DNS360LB-CR-PIR-DYNET Multifunction Sensor 45° C (113° F) 0° C (32° F) ≤90% Devices must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations. Les appareils doivent être installés par un électricien diplômé conformément à tous les codes et réglementations électriques et de construction nationaux et locaux. Die Geräte sind von einem qualifizierten Elektriker in Übereinstimmung mit allen geltenden Vorschriften zu installieren. Los dispositivos deben ser instalados por un electricista calificado y cumpliendo todas las normas y regulaciones, tanto nacionales como locales, sobre instalaciones eléctricas y obras. I dispositivi devono essere installati da un elettricista qualificato in conformità con le norme locali e nazionali vigenti in materia di costruzioni edilizie e installazione di impianti elettrici. De apparaten moeten worden aangebracht door een gekwalificeerde elektricien en in overeenstemming met alle nationale en plaatselijke elektriciteits- en bouwvoorschriften. 装置を取り付ける際は、資格のある電気技師に依頼し、 国および地域の電気および建設に関するすべての法令に 従ってください。 根据国家/地区及当地的电气与建筑规范和法规，该设 备必须由有资质的电工进行安装。 . 0.5 Nm 4.4 Lb-in Reset Switch 12 - 24 V 5 mA RS-485 DyNet SELV/Class 2 (UL) 12-24 V D- ≤ 20 mm (0.79 in) D+ GND SHLD 0.3-2.5 mm 2 22-12 AWG 0.4 Nm 3.5 Lb-in 64 mm (2.5 in) +V D- D+ GND SHLD ≤ 2 A 6.5 mm (0.26 in) 4.5 mm (0.18 in) 3 – 25 mm (0.12 – 0.98 in) 4.5 mm (0.18 in) 64 mm (2.5 in) DALI Insulation: Basic DA DA DALI ELV 12 - 22.5 V 5 mA 0.4 Nm 3.5 Lb-in ≤1 mm 2 16+ AWG x2 60° 60° 34 8 9 RS-485 DyNet PEIR 5 6 7 IEC Overvoltage Category II AZZ 626 0526 Pr05 © 2026 Signify Holding. All rights reserved. Specifications are subject to change without notice. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. Trademarks are owned by Signify Holding or their respective owners. www.dynalite.com FCC Radiation Exposure Statement – This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated with a minimum distance 20cm between the radiator and your body. ISED Radiation Exposure Statement – This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet équipement respecte les limites d’exposition aux rayonnements ionisants fixées pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20cm entre le radiateur et votre corps. Cet émetteur ne doit pas être localisé ou fonctionner en conjonction avec une autre antenne ou un autre émetteur. Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice – This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any modifications not approved by the manufacturer of this device could void the user’s authority to operate this device. This device complies with part 15 of the FCC Rules and Innovation, Science and Economic Development Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil contient des émetteurs/récepteurs exemptés de licence qui sont conformes aux RSS exemptés de licence d’innovation, sciences et développement économique Canada. Le fonctionnement est soumis aux deux conditions suivantes: (1) Cet appareil ne peut pas causer d’interférences. (2) Cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un fonctionnement indésirable de l’appareil. This Class B digital apparatus complies with Canadian ICES-003: CAN ICES-003(B)/NMB-003(B). Cet appareil numerique de la Classe B est conforme a la norme NMB-003 du Canada: CAN ICES-003(B)/NMB-003(B). Installation of a home and building automation and control system shall comply with IEC 60364 (all parts). The temperature limits and current-carrying capacities for the communication wires specified in IEC 60364-5-52 shall not be exceeded. the communication wires specified in IEC 60364-5-52 shall not be exceeded. Refer to…

Text truncated - open the document above for the full version.

CFR 47 §2.911 (d)(7) Agent Designation Attestation Date: 2026-03-31 FRN: 0024909822 FCC ID: 2AF2NDNS360LB Product Model Number: DNS360LB-CR-PIR-DYNET, DNS360LB-CR-PIR-DYNET-RAL9005 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Signify North America Corporation (“the applicant”) as required by section 2.911(d)(7), designates the following agent, located in the United States, for purposes of acting as the applicant’s agent for service of process. The applicant acknowledges that they will maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the agent information changes. U. S. Agent Information: Contact Person: Yuhong Fang Company Name: Signify North America Corporation Company Address: 10275 West Higgins Road, Rosemont, IL 60018 Email: [email protected] Sincerely yours, Name: Yuhong Fang Job Title: R&D Architect Company Name: Signify North America Corporation Email: [email protected]

CFR 47 §2.911 (d)(5) Attestation v1 Date: 2026-03-31 FRN: 0024909822 FCC ID: 2AF2NDNS360LB Product Model Number: DNS360LB-CR-PIR-DYNET, DNS360LB-CR-PIR-DYNET-RAL9005 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA 1. Signify North America Corporation (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. 2. Signify (China) Investment Co., Ltd (“the applicant”) certifies that, the device does not have cybersecurity and / or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, identified on the Covered List installed on the device, nor will it be installed by the applicant any time after certification. Sincerely yours, Name: Yuhong Fang Address: 10275 West Higgins Road, Rosemont, IL 60018 Email: [email protected] Job Title: R&D Architect Company Name: Signify North America Corporation

CFR 47 §2.911 (d)(5) Attestation v2 Date: 2026-03-31 FRN: 0024909822 FCC ID: 2AF2NDNS360LB Product Model Number: DNS360LB-CR-PIR-DYNET, DNS360LB-CR-PIR-DYNET-RAL9005 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA 1. Signify North America Corporation (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment and is not an affiliate or subsidiary of an entity identified on the Covered List. Sincerely yours, Name: Yuhong Fang Address: 10275 West Higgins Road, Rosemont, IL 60018 Email: [email protected] Job Title: R&D Architect Company Name: Signify North America Corporation

Signify North America Corporation POWER OF ATTORNEY DATE: March 9, 2026 To Whom It May Concern: We, the undersigned, hereby authorize Eurofins TA Technology (Shanghai) Co., Ltd /Liu Mengting on our behalf, to apply to FCC Approval for FCC ID: 2AF2NDNS360LB on our equipment. Any and all acts carried out by Eurofins TA Technology (Shanghai) Co., Ltd/Liu Mengting on our behalf shall have the same effect as acts of our own. Sincerely, Signify North America Corporation <SIGNATURE> ---------------------- (PERSON) Yuhong Fang -------------- (TITLE) R&D Architect ---------------

Signify North America Corporation Request for Confidentiality Date: 2026/3/09 Subject: Confidentiality Request for: _____ FCC ID: 2AF2NDNS360LB _____ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 1 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual *Note: ______(Insert Explanation as Necessary)______ ____ Signify North America Corporation_____ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of __ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TCB in the event information regarding the product or the product is made available to the public. TCB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, R&D Architect By: Yuhong Fang (Signature/Title 2 ) (Print name)

Signify North America Corporaon Date: May 8, 2026 Dear Examiner, The main differences between the two models are described below: Different Model DNS360LB-CR-PIR-DyNet DNS360LB-CR-PIR-DyNet-RAL9005 HVIN DNS360LB-CR-PIR-DyNet DNS360LB-CR-PIR-DyNet-RAL9005 12NC 913703274409 913703405209 Descripon DyNet, Ceiling Recessed white DyNet, Ceiling Recessed Black Main difference is the color of the case is different Sincerely yours, Name: Liu Mengng Company: Signify North America Corporaon

EUT Appearance Report No.: EFTA25120109-IE-04 Eurofins TA Technology (Shanghai) Co., Ltd. TA-MB-01-032E Page 1 of 3 This report shall not be reproduced except in full, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd. EUT Appearance DNS360LB-CR-PIR-DyNet EUT Appearance Report No.: EFTA25120109-IE-04 Eurofins TA Technology (Shanghai) Co., Ltd. TA-MB-01-032E Page 2 of 3 This report shall not be reproduced except in full, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd. EUT Appearance Report No.: EFTA25120109-IE-04 Eurofins TA Technology (Shanghai) Co., Ltd. TA-MB-01-032E Page 3 of 3 This report shall not be reproduced except in full, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd. Picture 1: Constituents of EUT

EUT Appearance Report No.: EFTA25120109-IE-04 Eurofins TA Technology (Shanghai) Co., Ltd. TA-MB-01-032E Page 1 of 3 This report shall not be reproduced except in full, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd. EUT Appearance DNS360LB-CR-PIR-DyNet-RAL9005 EUT Appearance Report No.: EFTA25120109-IE-04 Eurofins TA Technology (Shanghai) Co., Ltd. TA-MB-01-032E Page 2 of 3 This report shall not be reproduced except in full, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd. EUT Appearance Report No.: EFTA25120109-IE-04 Eurofins TA Technology (Shanghai) Co., Ltd. TA-MB-01-032E Page 3 of 3 This report shall not be reproduced except in full, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd. Picture 1: Constituents of EUT

Shld Gnd D+ D- +V ENERGY MGT EQPT E546032 DNS360LB-CR-PIR-DYNET Multifunction Sensor SUPPLY: 12-24 Vdc, 10 mA max, SELV /Class 2 (UL) Ta: 0°- 45°C (32°- 113°F) CAN ICES-003(B)/NMB-003(B) IC: 20659-DNS360LB FCC ID: 2AF2NDNS360LB www.dynalite.com Made in Australia Signify, IBRS 10461, 5600VB, NL Revision Drawn Checked Approved Date ECO Drawing Scale: PART NUMBER: DESCRIPTION: PRODUCTION PROCESS: MATERIAL: COLOUR: FINISH: 3568 A B C D E F G A B C D E F G 12479 1 2 47 9 3 56 8 Page Size A4 Part NumberPart NameQuantity Bill Of Materials Back Cover Assy Labelled DNS360LB-CR-PIR-DyNet Laser Engraved As per BOM Light Grey (close to RAL 7035) - 282-302-01 Rev4 Not to Scale Sheet 1 of 1 282-298-01 Rev2Back Cover Assy DNS360LB 1 NOTES Layer “INFORMATION” - All drawing information Layer “CUT” - All cut details Layer “ARTWORK” - All artwork details Layer “HOUSING” -For reference only Layer “PCB” -For reference only - Dimensional Tolerance ±0.5mm - Graphics to Cut line Tolerance ±0.5mm - Colours must be true to specified RAL Rev 4 Andrew Larkin - - 09/03/26 - Rev2 Andrew Larkin - - 10/12/2025 - Rev3 Andrew Larkin - - 09/02/2026 All Laser marking on these faces

Shld Gnd D+ D- +V ENERGY MGT EQPT E546032 DNS360LB-CR-PIR-DYNET-RAL9005 Multifunction Sensor SUPPLY: 12-24 Vdc, 10 mA max, SELV /Class 2 (UL) Ta: 0°- 45°C (32°- 113°F) CAN ICES-003(B)/NMB-003(B) IC: 20659-DNS360LB FCC ID: 2AF2NDNS360LB www.dynalite.com Made in Australia Signify, IBRS 10461, 5600VB, NL Revision Drawn Checked Approved Date ECO Drawing Scale: PART NUMBER: DESCRIPTION: PRODUCTION PROCESS: MATERIAL: COLOUR: FINISH: 3568 A B C D E F G A B C D E F G 12479 1 2 47 9 3 56 8 Page Size A4 Part NumberPart NameQuantity Bill Of Materials Back Cover Assy Labelled DNS360LB-CR-PIR-DyNet-RAL9005 Laser Engraved As per BOM Light Grey (close to RAL 7035) - 282-313-01 Rev4 Not to Scale Sheet 1 of 1 282-298-01 Rev2Back Cover Assy DNS360LB 1 NOTES Layer “INFORMATION” - All drawing information Layer “CUT” - All cut details Layer “ARTWORK” - All artwork details Layer “HOUSING” -For reference only Layer “PCB” -For reference only - Dimensional Tolerance ±0.5mm - Graphics to Cut line Tolerance ±0.5mm - Colours must be true to specified RAL Rev 4 Andrew Larkin - - 09/03/26 - Rev2 Andrew Larkin - - 10/12/2025 - Rev 3 Andrew Larkin - - 09/02/2026 - All Laser marking on these faces

Internal photo Eurofins TA Technology (Shanghai) Co., Ltd. TA-MB-01-033E Page 1 of 4 This report shall not be reproduced except in full, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd. Internal photo DNS360LB-CR-PIR-DyNet Internal photo Eurofins TA Technology (Shanghai) Co., Ltd. TA-MB-01-033E Page 2 of 4 This report shall not be reproduced except in full, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd. Internal photo Eurofins TA Technology (Shanghai) Co., Ltd. TA-MB-01-033E Page 3 of 4 This report shall not be reproduced except in full, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd. Internal photo Eurofins TA Technology (Shanghai) Co., Ltd. TA-MB-01-033E Page 4 of 4 This report shall not be reproduced except in full, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd.

Internal photo Eurofins TA Technology (Shanghai) Co., Ltd. TA-MB-01-033E Page 1 of 3 This report shall not be reproduced except in full, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd. Internal photo DNS360LB-CR-PIR-DyNet-RAL9005 Internal photo Eurofins TA Technology (Shanghai) Co., Ltd. TA-MB-01-033E Page 2 of 3 This report shall not be reproduced except in full, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd. Internal photo Eurofins TA Technology (Shanghai) Co., Ltd. TA-MB-01-033E Page 3 of 3 This report shall not be reproduced except in full, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd. Antenna

Prepared by: Liu Wei Approved by: Xu Kai Eurofins TA Technology (Shanghai) Co., Ltd. Building 3, No.145, Jintang Rd, Pudong Shanghai, P.R.China TEL: +86-021-50791141/2/3 FAX: +86-021-50791141/2/3-8000 EMC TEST REPORT Applicant Signify North America Corporation FCC ID 2AF2NDNS360LB Product Multifunction Sensor Brand Signify Dynalite Model DNS360LB-CR-PIR-DyNet; DNS360LB-CR-PIR-DyNet-RAL9005 Report No. EFTA25120109-IE-04-E1 Issue Date April 13, 2026 Eurofins TA Technology (Shanghai) Co., Ltd. tested the above equipment in accordance with the requirements in FCC Code CFR47 Part15B (2025)/ ANSI C63.4-2014. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Test Report Report No.: EFTA25120109-IE-04-E1 Eurofins TA Technology (Shanghai) Co., Ltd. TA-MB-06-001E Page 2 of 19 This report shall not be reproduced except in full, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd. Table of Contents 1 Test Laboratory ................................................................................................................................. 4 1.1 Notes of the Test Report ............................................................................................................ 4 1.2 Test Facility ................................................................................................................................ 4 1.3 Testing Location......................................................................................................................... 4 2 General Description of Equipment Under Test ................................................................................. 5 2.1 Applicant and Manufacturer Information ................................................................................... 5 2.2 General Information ................................................................................................................... 5 2.3 Applied Standards ..................................................................................................................... 6 2.4 Test Mode .................................................................................................................................. 7 3 Test Case Results ............................................................................................................................. 8 3.1 Radiated Emission ..................................................................................................................... 8 3.2 Conducted Emission ................................................................................................................ 13 4 Uncertainty Measurement ............................................................................................................... 16 5 Main Test Instruments ..................................................................................................................... 17 6 The EUT Appearance ...................................................................................................................... 18 7 Test Setup Photos ........................................................................................................................... 19 Test Report Report No.: EFTA25120109-IE-04-E1 Eurofins TA Technology (Shanghai) Co., Ltd. TA-MB-06-001E Page 3 of 19 This report shall not be reproduced except in full, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd. Summary of measurement results Number Test Case Clause in FCC Rules Conclusion 1 Radiated Emission FCC Part15.109, ANSI C63.4-2014 PASS 2 Conducted Emission FCC Part15.107, ANSI C63.4-2014 PASS Date of Testing: December 24, 2025 ~ December 26, 2025 Date of Sample Received: December 10, 2025 Note: 1. The conformity assessment in this report is based on a direct comparison of the test results with the limits by Eurofins TA Technology (Shanghai) Co., Ltd., without considering measurement uncertainty. Test Report Report No.: EFTA25120109-IE-04-E1 Eurofins TA Technology (Shanghai) Co., Ltd. TA-MB-06-001E Page 4 of 19 This report shall not be reproduced except in full, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd. 1 Test Laboratory 1.1 Notes of the Test Report This report shall not be reproduced in full or partial, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd. The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. Measurement Uncertainties were not taken into account and are published for informational purposes only. This report is written to support regulatory compliance of the applicable standards stated above. 1.2 Test Facility FCC (Designation number: CN1179, Test Firm Registration Number: 446626) Eurofins TA Technology (Shanghai) Co., Ltd. has been listed on the US Federal Communications Commission list of test facilities recognized to perform measurements. A2LA (Certificate Number: 3857.01) Eurofins TA Technology (Shanghai) Co., Ltd. has been listed by American Association for Laboratory Accreditation to perform measurement. 1.3 Testing Location Company: Eurofins TA Technology (Shanghai) Co., Ltd. Address: Building 3, No.145, Jintang Rd, Pudong Shanghai, P.R.China City: Shanghai Post code: 201201 Country: P. R. China Contact: Xu Kai Telephone: +86-021-50791141/2/3 Fax: +86-021-50791141/2/3-8000 Website: https://www.eurofins.com/electrical-and-electronics E-mail: [email protected] Test Report Report No.: EFTA25120109-IE-04-E1 Eurofins TA Technology (Shanghai) Co., Ltd. TA-MB-06-001E Page 5 of 19 This report shall not be reproduced except in full, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd. 2 General Description of Equipment Under Test 2.1 Applicant and Manufacturer Information Applicant Signify North America Corporation Applicant address 10275 …

Text truncated - open the document above for the full version.

EMC Test Setup Report No.: EFTA25120109-IE-04 Eurofins TA Technology (Shanghai) Co., Ltd. TA-MB-01-031E Page 1 of 2 This report shall not be reproduced except in full, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd. Part 15B EMC Test Setup 30MHz-1GHz 1GHz-18GHz Picture 1: Radiated Emission Test Setup EMC Test Setup Report No.: EFTA25120109-IE-04 Eurofins TA Technology (Shanghai) Co., Ltd. TA-MB-01-031E Page 2 of 2 This report shall not be reproduced except in full, without the written approval of Eurofins TA Technology (Shanghai) Co., Ltd. Picture 2: Conducted Emissions Test Setup