2AF3W-1134904Velociradar

Velociradar tm INSTRUCTIONS & SAFETY INFORMATION Please visit www.caldwellshooting.com/warranty or contact Customer Service at 1-833-784-5520 for complete warranty terms and conditions. For purchasing replacement parts, please contact Caldwell Customer Service NOT WARRANTED AGAINST MISUSE, ABUSE, OR COMMERCIAL USE. CONTENTS Ball Head Tripod Velociradar TM Chronograph Recoil Trigger USB-C Charging Cable 1. Firearm and shooting safety rules 2. Airgun and paintball gun safety rules 3. Ammunition reloading safety rules 4. Archery safety rules If you are not familiar with applicable rules for your application consult the manufacturer(s) of the firearm, airgun, paintball gun, bow or reloading equipment/component... Read thoroughly all directions and safety instructions included in the package. Failure to comply may result in an unsafe firearm condition that may cause property damage, person- al injury or death. As with any electronic device, water can damage certain components. To prevent damage, do not use chronograph outside when it is raining without being protected. WARNING: Velocity measurements should not be used to calculate combustion pressures in your cartridge or chamber. Again, do not exceed published maximum powder levels in your ammunition. WARNING: Do not try to protect your chronograph with armor plating. Bullet ricochet from hitting this plating could cause property damage, personal injury or death. Intentional or unintentional shooting of the chronograph will void factory warranty. SAFETY AND WARNINGS WARNING: Target must have a safe backstop. Always follow all applicable safety rules while using the chronograph, including but not limited to: SPECIFICATIONS Velocity Range: 250-4500 FPS Battery: Rechargeable Lithium-Ion, 7.4V, 2500mAh, 18.5Wh Charging Input: USB-C 5V, 700mA Operating Temperature: 0-130 degrees F Smart Phone Interface: Bluetooth Low Energy (BLE) Radar Transmission Frequency: 24075MHz to 24175MHz Model #1134904 Recoil Trigger OVERVIEW 1. Directional Buttons – Press to navigate menus. 2. Power Button – Press to turn on and off Velociradar. 3. Select Button – Press to select options and enter menus. 4. Back Button – Press to undo and exit menus. 5. Arm Button – Press to disable/enable radar during a string. 6. USB-C Charging Port – For charging the internal lithium-ion battery. 7. Recoil Trigger Port – For connecting the included external recoil trigger. 8. Peep Sight – For aligning the radar to the target. 9. ¼”-20 Mount – For included ball head tripod or other mounting attachment. CHARGING Connect the included USB-C charging cable to the USB-C charging port of the Velociradar. Connect the other end of the charging cable to a 500mA or greater USB charging adapter or power bank. You will not be able to use the Velociradar while it is charging. WARNING: The Velociradar contains a lithium-ion battery. To prevent the possibility of personal injury, product damage, or other property damage caused by battery exposure to extreme heat, store the device out of direct sun- light. To avoid over-heating, do NOT charge this device in high temperatures or humidity. POWERING ON/OFF Power On: (When Velociradar is off) Hold the Power Button for 1 second until the screen turns on. Power Off: (When Velociradar is on) Press and release the Power Button. 1 2 3 4 5 6 7 8 9 OPERATION The Velociradar Chronograph captures advanced ballistic data safely from behind the firing line. It can be set up near the firearm using the included ball head tripod and aimed using the integral peep sight. The radar is activated using the internal acoustic trigger (using muzzle blast) or by using the external recoil trigger (included), securely attached to the firearm or bow. To use the Velociradar, follow these steps: 1. Set up a shooting target 100 yards away. The target may be set up closer if necessary, but the Velociradar cannot track the bullet once it is past the target. 2. Set up your shooting position in a safe and comfortable location. Ensure that you have enough space to place the Velociradar on a tripod next to your firearm or bow. 3. Attach the Velociradar securely to the included ball head tripod. Turn on the Velociradar by pressing and holding the Power Button until the display turns on. 4. Choose the Acoustic Trigger or the Recoil Trigger to activate the radar. Select the trigger mode in the setting menu on the Velociradar or in the app. 5. If you are using the Recoil Trigger, attach it to your firearm or bow using the provided cable and strap. Follow the instructions in the Recoil Trigger section for more details. 6. Start a new string on the Velociradar by selecting New String from the main menu. You can also choose to continue an existing string if you want to add more shots to it. 7. Press any button to pause the radar. The display will show that the string is paused. To resume, press the Arm Button again. 8. Aim the Velociradar by centering the target inside the peep sight. Make sure the Velociradar is level and stable on the tripod. 9. Aim your firearm or bow at the same target as the Velociradar. Make sure the muzzle is even with or slightly in front of the Velociradar. Never shoot from behind the Velociradar to avoid accidental impact and damage. 10. Take the first shot. The Velociradar will detect the shot using the selected trigger and measure the velocity and other ballistic data of the projectile. The data will be displayed on the screen after a few seconds. 11. Repeat the steps above for each shot you want to record. The Velociradar will store up to 100 shots per string. 12. String data is saved after every shot. When you are finished with the string, press the back button to return to the main menu. SETUP TIPS The Velociradar measures the speed and distance of the projectile while it is in the radar beam. For reliable measurement: The Velociradar should be as close to the muzzle or release point without being in danger of impact or excessive muzzle blast. Set up the target at…

Text truncated - open the document above for the full version.

AOB Products Company 2.911 (d)(5)(ii) Applicant Attestation v1.3 Section 2.911(d)(5)(ii) Certification – Applicant (Covered List ) Company name: AOB Products Company Address: 1800 North Route Z, Suite A, Columbia, Missouri 65202, United States Product Name: Velociradar FCC ID: 2AF3W-1134904 Model(s): 1134904 2.911(d)(5)(ii) Applicant filing We, [AOB Products Company] (“the applicant”) certify that, as of the date of the filing of the application, the applicant is not identified NOTE 1 on the “Covered List” NOTE 2 ,established pursuant to §1.50002 of this chapter,as an entity producing coveredcommunications equipment. Yours sincerely, Name: Michael Galloway Date: 2024-06-03 Title and Company name: Quality Engineering Manager /AOB Products Company NOTE 1 Delete option not applicable to this application. NOTE 2 “Covered List ”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

AOB Products Company 2.911 (d)(7)USA Agent v1.5 Section 2.911(d)(7) USA Agent for Service of Process Company name: AOB Products Company Address: 1800 North Route Z, Suite A, Columbia, Missouri 65202, United States Product Name: Velociradar FCCID: 2AF3W-1134904 Model(s): 1134904 2.911(d)(7) USA Designated Agent for Service of Process We, [AOB Products Company] (“the applicant”) designate [AOB Products Company ] NOTE1 for the purpose of accepting service of process on behalf of the applicant. Applicant consent:We acknowledgeour consent to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address of the designated agent and acknowledgeour acceptance of our obligation to maintain an agent for service of process in the United States for no less than one year after either we the grantee have permanently terminated all marketing and importation of the applicable equipment within the U.S., or at the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Agent obligation:We acknowledgeourobligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email addressfor no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or at the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. USA Agent Company name: AOB Products Company USA Address: 1800 North Route Z, Suite A, Columbia, Missouri 65202, United States FRN Number: 0024925240 Contact Name: Michael Galloway Telephone No: 5733476377 Email: [email protected] Applicant Company name: AOB Products Company Address: 1800 North Route Z, Suite A, Columbia, Missouri 65202, United States Grantee FRN Number: 0024925240 FCC Grantee Code: 2AF3W Contact Name: Michael Galloway Telephone No: 5733476377 Email:[email protected] Signature: Title: Quality Engineering Manager Signature: Title: Quality Engineering Manager Date:2024-06-03 Date: 2024-06-03 AOB Products Company 2.911 (d)(7)USA Agent v1.5 NOTE 1: An applicant located in the United States may designate itself as the agent for service of process. Reference; Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-nation al-security-threats-to-the-communications-supply-chain-through-the

AOB Products Company 2.911 (d)(5)(i) Equipment Type Attestation v1.2 Section 2.911(d)(5)(i) Certification – EquipmentType Company name: AOB Products Company Address: 1800 North Route Z, Suite A, Columbia, Missouri 65202, United States Product Name: Velociradar FCC ID: 2AF3W-1134904 Model(s): 1134904 2.911(d)(5)(i) EquipmentType We, [AOB Products Company] (“the applicant”) certify that the equipment for which authorization is sought through certification is not: • Prohibited from receiving an equipment authorization pursuant to § 2.903; of the FCC rules. • Identified as an equipment type in the “Covered List” NOTE 1 Yours sincerely, Name: Michael Galloway Date: 2024-06-03 Title and Company name: Quality Engineering Manager /AOB Products Company NOTE 1 “Covered List ”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

AOB Products Company Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2024-06-03 Subject; Request for Long Term Confidentiality FCC ID: 2AF3W-1134904 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Michael Galloway Title: Quality Engineering Manager

AOB Products Company 1800 North Route Z, Suite A, Columbia, Missouri 65202, United States Agent Authorization Company : AOB Products Company Address: 1800 North Route Z, Suite A, Columbia, Missouri 65202, United States Product Name: Velociradar Model Number(s): 1134904 Product Description: Velociradar We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2024-06-03 Name: Michael Galloway Title: Quality Engineering Manager Company: AOB Products Company

Page 1 of 4 Appendix C: Photographs of EUT Product: Velociradar Model: 1134904 External Photos Page 2 of 4 Page 3 of 4 Page 4 of 4

Label Artwork and Location Model: 1134904 Step1: Select to SETTINGS Step2: Select to FCC INFO

Page 1 of 6 Appendix C: Photographs of EUT Product: Velociradar Model: 1134904 Internal Photos Page 2 of 6 Page 3 of 6 Page 4 of 6 Page 5 of 6 Antenna Page 6 of 6

Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com TEST REPORT FCC ID. ............................ : 2AF3W-1134904 Test Report No. ............... : TCT240105E005 Date of issue ................... : May 31, 2024 Testing laboratory .......... : SHENZHEN TONGCE TESTING LAB Testing location/ address: 2101 & 2201, Zhenchang Factory Renshan Industrial Zone, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518103, People's Republic of China Applicant's name ............ : AOB Products Company Address ........................... : 1800 North Route Z, Suite A, Columbia, Missouri 65202, United States Manufacturer's name ... : AOB Products Company Address ........................... : 1800 North Route Z, Suite A, Columbia, Missouri 65202, United States Standard(s) ..................... : KDB 447498 D01 General RF Exposure Guidance v06 Product Name ................. : Velociradar Trade Mark ...................... : N/A Model/Type reference..... : 1134904 Rating(s).......................... : Rechargeable Li-ion Battery DC 7.4V Date of receipt of test item ......................................... : Jan. 05, 2024 Date (s) of performance of test ................................... : Jan. 05, 2024 ~ May 31, 2024 Tested by (+signature) ... : Yannie ZHONG Check by (+signature) .... : Beryl ZHAO Approved by (+signature): Tomsin General disclaimer: This report shall not be reproduced except in full, without the written approval of SHENZHEN TONGCE TESTING LAB. This document may be altered or revised by SHENZHEN TONGCE TESTING LAB personnel only, and shall be noted in the revision section of the document. The test results in the report only apply to the tested sample. Report No.: TCT240105E005 Page 2 of 6 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com Table of Contents 1. General Product Information .................................................................. 3 1.1. EUT description ..................................................................................................... 3 1.2. Model(s) list ............................................................................................................ 3 2. General Information ................................................................................. 4 2.1. Test environment and mode ................................................................................. 4 2.2. Description of Support Units ................................................................................ 4 3. Facilities and Accreditations .................................................................. 5 3.1. Facilities ................................................................................................................. 5 3.2. Location ................................................................................................................. 5 4. Test Results and Measurement Data ..................................................... 6 Report No.: TCT240105E005 Page 3 of 6 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com 1. General Product Information 1.1. EUT description Product Name ....................... : Velociradar Model/Type reference........... : 1134904 Sample Number....................: TCT240105E004-0101 Operation Frequency ........... : 2402MHz~2480MHz Modulation Type ................... : GFSK Antenna Type ........................ : PCB Antenna Antenna Gain ........................ : 0dBi Rating(s)................................ : Rechargeable Li-ion Battery DC 7.4V Note: The antenna gain listed in this report is provided by applicant, and the test laboratory is not responsible for this parameter. 1.2. Model(s) list None. Report No.: TCT240105E005 Page 4 of 6 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com 2. General Information 2.1. Test environment and mode Item Normal condition Temperature +25ºC Voltage DC 7.4V Humidity 56% Atmospheric Pressure: 1008 mbar Test Mode: Engineering mode: Keep the EUT in continuous transmitting by select channel 2.2. Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Equipment Model No. Serial No. FCC ID Trade Name / / / / / Note: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. 3. For conducted measurements (Output Power, 20dB Occupied Bandwidth, Carrier Frequencies Separation, Hopping Channel Number, Dwell Time, Spurious Emissions), the antenna of EUT is connected to the test equipment via temporary antenna connector, the antenna connector is soldered on the antenna port of EUT, and the temporary antenna connector is listed in the Test Instruments. Report No.: TCT240105E005 Page 5 of 6 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com 3. Facilities and Accreditations 3.1. Facilities The test facility is recognized, certified, or accredited by the following organizations: ● FCC - Registration No.: 645098 SHENZHEN TONGCE TESTING LAB Designation Number: CN1205 The testing lab has been registered and fully described in a report with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. ● IC - Registration No.: 10668A-1 SHENZHEN TONGCE TESTING LAB CAB identifier: CN0031 The testing lab has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing. 3.2. Location SHENZHEN TONGCE TESTING LAB Address: 2101 & 2201, Zhenchang Factory, Renshan Industrial Zone, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518103, People's Republic …

Text truncated - open the document above for the full version.

OTA TEST REPORT Applicant Espressif Systems Product ESP-ANT A Model ESP-ANT A Report No. YXA1711-1424OTA01R1 Issue Date November 30, 2017 TA Technology (Shanghai) Co., Ltd. tested the above equipment in accordance with the requirements in ANSI/IEEE Std 149-2008. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Performed by: Jiangpeng Lan Approved by: Kai Xu TA Technology (Shanghai) Co., Ltd. No.145, Jintang Rd, Tangzhen Industry Park, Pudong Shanghai, China TEL: +86‐021‐50791141/2/3 FAX: +86‐021‐50791141/2/3‐8000 OTA Test Report Report No: YXA1711-1424OTA01R1 TA Technology (Shanghai) Co., Ltd. TA-MB-04-008O P age 2 of 12 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. TABLE OF CONTENTS 1. General Information ....................................................................................................................... 3 1.1. Notes of the Test Report ................................................................................................... 3 1.2. Test facility ........................................................................................................................ 3 1.3. Testing laboratory .............................................................................................................. 4 1.4. Laboratory Environment .................................................................................................... 4 2. General Description of Equipment under Test ............................................................................... 5 2.1. Applicant Information ......................................................................................................... 5 2.2. Manufacturer Information .................................................................................................. 5 2.3. Information of EUT ............................................................................................................ 5 2.4. Test Date ........................................................................................................................... 5 2.5. Applied Standards ............................................................................................................. 6 3. Test Conditions .............................................................................................................................. 7 3.1. Test Configuration ............................................................................................................. 7 3.2. Test Measurement ............................................................................................................. 7 4. Test Results ................................................................................................................................... 8 4.1. Gain and Efficiency ............................................................................................................ 8 4.2. Voltage Standing Wave Ratio (VSWR) .............................................................................. 9 4.3. Antenna S11 ...................................................................................................................... 9 5. Test Equipment List ..................................................................................................................... 10 APPENDIX A: 2-D Pattern Plots ............................................................................................................. 11 APPENDIX B: The EUT Appearance and Test Configuration .................................................................. 12 B.1 EUT Appearance ................................................................................................................... 12 OTA Test Report Report No: YXA1711-1424OTA01R1 TA Technology (Shanghai) Co., Ltd. TA-MB-04-008O P age 3 of 12 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. 1. General Information 1.1. Notes of the Test Report This report shall not be reproduced in full or partial, without the written approval of TA technology (shanghai) co., Ltd.The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein .Measurement Uncertainties were not taken into account and are published for informational purposes only. This report is written to support regulatory compliance of the applicable standards stated above. This report must not be used by the client to claim product certification, approval, or endorsement by any government agencies. 1.2. Test facility CNAS (accreditation number:L2264) TA Technology (Shanghai) Co., Ltd. has obtained the accreditation of China National Accreditation Service for Conformity Assessment (CNAS). FCC (Designation number: CN1179, Test Firm Registration Number: 446626) TA Technology (Shanghai) Co., Ltd. has been listed on the US Federal Communications Commission list of test facilities recognized to perform electromagnetic emissions measurements. IC (recognition number is 8510A) TA Technology (Shanghai) Co., Ltd. has been listed by industry Canada to perform electromagnetic emission measurement. A2LA (Certificate Number: 3857.01) TA Technology (Shanghai) Co., Ltd. has been listed by American Association for Laboratory Accreditation to perform electromagnetic emission measurement. OTA Test Report Report No: YXA1711-1424OTA01R1 TA Technology (Shanghai) Co., Ltd. TA-MB-04-008O P age 4 of 12 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. 1.3. Testing laboratory Company: TA Technology (Shanghai) Co., Ltd. Address: No.145, Jintang Rd, Tangzhen Industry Park, Pudong City: Shanghai Post code: 201201 Country: P. R. China Contact: Xu Kai Telephone: +86-021-50791141/2/3 Fax: +86-021-50791141/2…

Text truncated - open the document above for the full version.

Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com TEST REPORT FCC ID. ............................ : 2AF3W-1134904 Test Report No. ............... : TCT240105E004 Date of issue ................... : May 31, 2024 Testing laboratory .......... : SHENZHEN TONGCE TESTING LAB Testing location/ address: 2101 & 2201, Zhenchang Factory Renshan Industrial Zone, Fuhai Subdistrict, Bao'an District, Shenzhen, Guangdong, 518103, People's Republic of China Applicant's name ............ : AOB Products Company Address ........................... : 1800 North Route Z, Suite A, Columbia, Missouri 65202, United States Manufacturer's name ... : AOB Products Company Address ........................... : 1800 North Route Z, Suite A, Columbia, Missouri 65202, United States Standard(s) ..................... : FCC CFR Title 47 Part 15 Subpart C Section 15.247 FCC KDB 558074 D01 15.247 Meas Guidance v05r02 ANSI C63.10:2013 Product Name ................. : Velociradar Trade Mark ...................... : N/A Model/Type reference..... : 1134904 Rating(s).......................... : Rechargeable Li-ion Battery DC 7.4V Date of receipt of test item ......................................... : Jan. 05, 2024 Date (s) of performance of test ................................... : Jan. 05, 2024 ~ May 31, 2024 Tested by (+signature) ... : Yannie ZHONG Check by (+signature) .... : Beryl ZHAO Approved by (+signature): Tomsin General disclaimer: This report shall not be reproduced except in full, without the written approval of SHENZHEN TONGCE TESTING LAB. This document may be altered or revised by SHENZHEN TONGCE TESTING LAB personnel only, and shall be noted in the revision section of the document. The test results in the report only apply to the tested sample. Report No.: TCT240105E004 Page 2 of 58 Hotline: 400-6611-140 Tel: 86-755-27673339 Fax: 86-755-27673332 http://www.tct-lab.com Table of Contents 1. General Product Information .................................................................. 3 1.1. EUT description ..................................................................................................... 3 1.2. Model(s) list ............................................................................................................ 3 1.3. Operation Frequency ............................................................................................ 3 2. Test Result Summary .............................................................................. 4 3. General Information ................................................................................. 5 3.1. Test environment and mode ................................................................................. 5 3.2. Description of Support Units ................................................................................ 5 4. Facilities and Accreditations .................................................................. 6 4.1. Facilities ................................................................................................................. 6 4.2. Location ................................................................................................................. 6 4.3. Measurement Uncertainty ..................................................................................... 6 5. Test Results and Measurement Data ..................................................... 7 5.1. Antenna requirement ............................................................................................ 7 5.2. Conducted Emission ............................................................................................. 8 5.3. Conducted Output Power ................................................................................... 12 5.4. Emission Bandwidth ........................................................................................... 13 5.5. Power Spectral Density ....................................................................................... 14 5.6. Conducted Band Edge and Spurious Emission Measurement ....................... 15 5.7. Radiated Spurious Emission Measurement ...................................................... 17 Appendix A: Test Result of Conducted Test Appendix B: Photographs of Test Setup Appendix C: Photographs…

Text truncated - open the document above for the full version.