2AF4P-LL13.56MHz RFID Reader/Writer Module

Operation Manual Introduction Teraoka Seiko Co., Ltd. Wrapping & Ecological System Division Integrated Weigh /Label System Original Instructions DPS-5600M FOREWORD This Operation Manual is for the DIGI DPS-5600M manufactured by TERAOKA SEIKO CO., LTD. in Japan. Please keep this Operation Manual always beside the machine. If any parts are missing or become difficult to read by stains or tearing, please contact your DIGI dealer/distributor to obtain a new one. Your DIGI Dealer : DPS-5600M Serial No. : OPERATION MANUAL: DPS-5600M Basic Operation 1st edition: Oct 2013 TERAOKA SEIKO CO., LTD. Wrapping & Ecological System Division 5-13-12 Kugahara, Ohta-ku, Tokyo 146-8580 Tel: +81-3-3752-0327 Fax: +81-3-3752-5814 Teraoka Seiko, DIGI and Teraoka are registered trademarks of Teraoka Seiko Co., Ltd. Most accidents involving machine operation and maintenance are caused by failure to observe basic safety rules or precautions. An accident can often be prevented by recognizing potential hazards. Do NOT operate this machine until you have completely read and understood the precautions in this manual. Follow all the safety precautions when checking, starting, operating, stopping or performing any maintenance on this machine. The basic safety precautions given in this manual and the warning labels placed on the machine are: The machine is designed to be operated by one person. However, feeding package and/or carrying processed package out from the machine can be done by other persons as assistance to the operator. Even in these cases, machine should only be operated by a person who is instructed to operate the machine from DIGI dealer directly or indirectly. The operator should fully understand the basic safety rules, indicated in the next page, and the operation procedures mentioned in this manual and follow them. If a procedure or working method not specifically recommended by TERAOKA is used, the operator must be positive that it is safe for him/her and others. The operator should also ensure that the machine would not be damaged by the method of operation chosen. The operator must NOT operate the machine when he/she is not good health to pay attention to the machine. Should an accident occur, it is advisable to follow these steps: (1) Obtain first aid or medical attention immediately after an injury. Do NOT neglect an injury, no matter how slight it seems. (2) Report it to your manager and DIGI dealer to make an investigation. (3) Enforce precautionary measures to prevent recurrence of the accident. There may be some changes to the machine not included in this publication because of further improvements and advancements in product design. If there are any questions about the machine or this publication, please consult your DIGI dealer before operating the machine. The appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. The machine is CE marked in accordance with the following Directives. ・NAWI Directive ・EMC Directive ・Machinery Directive IMPORTANT - FOR SAFETY OPERATION Hazardous situation or unsafe practices which COULD result in severe personal injury. Hazardous situation or unsafe practices which COULD result in minor personal injury and/or product or property damage. WARNING CAUTION １． Do not plug in and out with your hands wet. Grab a plug without pulling out power cord. Failure to do so, it might result in an electric shock. ２． Handle power cord carefully. Do not put heavy object on power cord. Do not place power cord near heated object. Do not modify, bend and pull out power cord. In case of damaged, turn off the power switch and plug out immediately, and contact our sales representatives. Failure to do so, it might result in an electric shock. ３． Set up ground wire to earth properly. Failure to do so, it might result in fire, electric shock and machine defect. If ground wire can not be set up, contact our sales representatives. ４． Do not repair, conversion and dismantle the machine. Failure to do so, it might result in fire, electric shock and machine defect, except points mentioned in this manual. ５． Install the machine away from steam, corrosive gas or inflammable gas. Failure to do so, it might result in fire, electric shock and machine defect. ＜For Linerless＞ ６． In case of swallowing oil, receive medical treatment immediately. ７． In case of getting oil in eyes, irrigate eyes with plenty of water for more than 15 minutes immediately. If stimulus becomes strong or continues, receive medical treatment. ８．Do not put any objects or other liquids into the fluid of oil. WARNING １. Check up the machine twice a year at least. The periodic check-up will prevent a mechanical trouble. Contact our sales representatives for check up. ２. Do not place machine by high precision device. Failure to do so, it might result in malfunction of device. ３. Install the machine on level and stable place. Failure to do so, it might result in fire, electric shock and machine defect. ４. Do not install the machine under excessive heat, humidity and dusty environment. Failure to do so, it might result in fire, electric shock and machine defect. ５. Use the machine under an adequate power source and voltage indicated on the nameplate. Failure to do so, it might result in fire, electric shock and machine defect. ６. Don't put any object and any liquid into the machine. Failure to do so, it might result in fire, electric shock and machine defect. ７. Turn off the power switch and plug out immediately when the machine falls down or has an impact. Failure to do so, it might result in fire, electric shock and machine defect. ８. Turn off the power switch and plug out immediately when the machine has foul smell, odd sound, overheating, and smoke. Failure to do so, it might result in fire, electric shock and machine defect. ９． Turn off the power switch and plug out when the machine is n…

Text truncated - open the document above for the full version.

Contains FCC ID:2AF4P-LL Contains IC:20690-LL This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference,and (2) this device must accept any interference received, including interference that may cause undesired operation Since this module is not sold to general end users directly there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to installation procedure. This is the label drawing placed on the host device.

Photo TERAOKA SEIKO CO.,LTD.. [Model: ASI4000R2X]

Photo TERAOKA SEIKO CO.,LTD.. [Model: ASI4000R2X]

Test report No. : 11008659S-A Page : 1 of 42 Issued date : October 23, 2015 Revised date : November 19, 2015 FCC ID : 2AF4P-LL UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 RADIO TEST REPORT Test Report No.: 11008659S-A Applicant : ART Finex Co., Ltd. Type of Equipment : 13.56 MHz RFID Reader/Writer Module Model No. : ASI4000R2X FCC ID : 2AF4P-LL Test regulation : FCC Part15 Subpart C: 2015 Test result : Complied 1. This test report shall not be reproduced in full or partial, without the written approval of UL Japan, Inc. 2. The results in this report apply only to the sample tested. 3. This sample tested is in compliance with the limits of the above regulation. 4. The test results in this test report are traceable to the national or international standards. 5. This test report must not be used by the customer to claim product certification, approval, or endorsement by any agency of the Federal Government. 6. The opinions and the interpretations to the result of the description in this report are outside scopes where UL Japan has been accredited. 7. This test report covers Radio technical requirements. It does not cover administrative issues such as Manual or non-Radio test related Requirements. (if applicable) Date of test: June 18 to August 17, 2015 Representative test engineer: Yosuke Ishikawa Engineer Consumer Technology Division Approved by : Toyokazu Imamura Leader Consumer Technology Division RTL02610 The testing in which "Non-accreditation" is displayed is outside the accreditation scopes in UL Japan. There is no testing item of "Non-accreditation". 13-EM-F0429 Test report No. : 11008659S-A Page : 2 of 42 Issued date : October 23, 2015 Revised date : November 19, 2015 FCC ID : 2AF4P-LL UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 REVISION HISTORY Original Test Report No.: 11008659S-A Revision Test report No. Date Page revised Contents - (Original) 11008659S-A October 23, 2015 - - 1 11008659S-A November 19, 2015 1, 4, 10-11, 17-29, 31-32 Correction of Type of equipment Test report No. : 11008659S-A Page : 3 of 42 Issued date : October 23, 2015 FCC ID : 2AF4P-LL UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 Contents Page SECTION 1: Customer information ........................................................................................ 4 SECTION 2: Equipment under test (E.U.T.) .......................................................................... 4 SECTION 3: Test specification, procedures & results ........................................................... 5 SECTION 4: Operation of E.U.T. during testing .................................................................... 9 SECTION 5: Conducted emission .......................................................................................... 12 SECTION 6: Radiated emission (Fundamental and Spurious emission) ........................... 13 SECTION 7: 20dB bandwidth & Occupied bandwidth (99%) ............................................ 15 SECTION 8: Frequency tolerances ........................................................................................ 15 Contents of APPENDIXES ....................................................................................................... 16 APPENDIX 1: Data of Radio tests .......................................................................................... 17 APPENDIX 2: Test instruments ............................................................................................. 33 APPENDIX 3: Photographs of test setup ............................................................................... 35 Test report No. : 11008659S-A Page : 4 of 42 Issued date : October 23, 2015 Revised date : November 19, 2015 FCC ID : 2AF4P-LL UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 SECTION 1: Customer information Company Name : ART Finex Co., Ltd. Address : 6-1-33 Kamikoubata-cho, Sabae-shi, Fukui-ken, 916-0037 Japan Telephone Number : +81-778-54-8085 Facsimile Number : +81-778-54-8092 Contact Person : Akio Yamamoto SECTION 2: Equipment under test (E.U.T.) 2.1 Identification of E.U.T. Type of equipment : 13.56 MHz RFID Reader/Writer Module Model No. : ASI4000R2X Serial No. : Refer to 4.2. Rating : DC 3.3 V Country of Mass-production : Japan Condition of EUT : Production model Receipt Date of Sample : June 18, 2015 2.2 Product description Model: ASI4000R2X (referred to as the EUT in this report) is a 13.56 MHz RFID Reader/Writer Module. Clock frequency(ies) in the system : 13.56 MHz Radio part: Equipment type : Transceiver Frequency of operation : 13.56 MHz Type of modulation : ASK Antenna type : Loop Antenna connector type : None ITU code : A1D FCC 15.31 (e) The stable voltage (DC 3.3 V) is provided to the EUT from the host device. Therefore, this EUT complies with the requirement. FCC 15.203 / 212 The antenna is not removable from the EUT. Therefore the EUT complies with the requirement. Test report No. : 11008659S-A Page : 5 of 42 Issued date : October 23, 2015 FCC ID : 2AF4P-LL UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 SECTION 3: Test specification, procedures & results 3.1 Test specification Test specification : FCC Part 15 Subpart C: 2015, final revised on September 8, 2015 Title : FCC 47CFR Part15 Radio Frequency Device Subpart C Intentional Radiators Section 15.207 Conducted limits Section 15.209 Radiated emission limits, general requirements Section 15.215 Additional provisions to the general radiated emission limitations Section 15.225 Operation within…

Text truncated - open the document above for the full version.

Test report No. : 10005707S-A Page : 21 of 23 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 APPENDIX 3: Photographs of test setup Conducted emission [Module alone] Front Side Test Report No 10768227S-A 35 of 42 Test report No. : 10005707S-A Page : 22 of 23 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 Conducted emission [Module built-in] Front Side Test Report No 10768227S-A 36 of 42 Test report No. : 10005707S-A Page : 23 of 23 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 Radiated emission [Module alone] Front Rear 9 kHz - 30 MHz Loop antenna: Horizontal Loop antenna: Vertical 30 MHz - 1000 MHz Test Report No 10768227S-A 37 of 42 Test report No. : 10005707S-A Page : 24 of 23 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 Radiated emission [Module built-in] Front Rear 9 kHz - 30 MHz Loop antenna: Horizontal Loop antenna: Vertical 30 MHz - 1000 MHz Test Report No 10768227S-A 38 of 42 Test report No. : 10005707S-A Page : 25 of 23 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 Pre-check of the worst case [Module alone] (1/2) EUT with Tag X-axis Y-axis Z-axis Test Report No 10768227S-A 39 of 42 Test report No. : 10005707S-A Page : 26 of 23 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 Pre-check of the worst case [Module alone] (2/2) EUT without Tag X-axis Y-axis Z-axis Test Report No 10768227S-A 40 of 42 Test report No. : 10005707S-A Page : 27 of 23 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 Tag used for the test as representative (1/2) ISO 15693 type Test Report No 10768227S-A 41 of 42 Test report No. : 10005707S-A Page : 28 of 23 UL Japan, Inc. Shonan EMC Lab. 1-22-3 Megumigaoka, Hiratsuka-shi, Kanagawa-ken, 259-1220 JAPAN Telephone : +81 463 50 6400 Facsimile : +81 463 50 6401 Tag used for the test as representative (2/2) FeliCa type END OF REPORT Test Report No 10768227S-A 42 of 42