2AF78-01778Payrange BluKey Select

BluKey Select™ Reference Manual Model: BluKey Select™ PayRange | BluKey Select™ Reference Manual 6/29/2021 Page 2 | 21 Table of Contents Table of Contents .......................................................................................................................................... 2 Introduction .................................................................................................................................................. 3 Before Installation ......................................................................................................................................... 6 1. Create your PayRange Operator Account ......................................................................................... 6 2. Setup for Your Machine Installers ..................................................................................................... 6 Installation Steps ........................................................................................................................................... 7 1. Disconnect power from the machine ............................................................................................... 7 2. Open machine cabinet ...................................................................................................................... 7 3. Connect Keypad Harness to Machine Keypad and Machine Control ............................................... 7 4. Connect configuration plug to CONF connector ............................................................................... 8 5. Plug Keypad Harness into BluKey Select KEYPAD connector ............................................................ 8 6. Plug MDB Machine harness into BluKey Select MACHINE connector .............................................. 8 7. Is Card Reader Present? .................................................................................................................... 8 8. Does machine support CPD2? ........................................................................................................... 8 9. Machine with no CPD2 support: Connect Card Reader to BluKey Select CARD connector .............. 8 10. Machine with CPD1/CPD2 support: Connect Card Reader to BluKey Select MDB harness ......... 8 11. Connect BluKey Select to Machine MDB connector ..................................................................... 9 12. Power up the machine (leave the machine door/panel open) ..................................................... 9 13. BluKey Select should power up and turn on solid blue LED ......................................................... 9 14. Configure BluKey Select ................................................................................................................ 9 15. Power off the machine .................................................................................................................. 9 16. Place wires and BluKey Select inside the machine ................................................................ ....... 9 17. Close machine door/panel ............................................................................................................ 9 18. Power up the machine .................................................................................................................. 9 19. Verify machine operation ............................................................................................................. 9 20. Place PayRange stickers on the machine ...................................................................................... 9 BluKey Select Device Configuration .............................................................................................................. 9 1. Register BluKey Select device (using website) .................................................................................. 9 2. Register BluKey Select device (using mobile app) .......................................................................... 10 3. Configure BluKey Select device for payment (using website) ........................................................ 10 BluKey Select Reference ............................................................................................................................. 11 Interfaces ................................................................................................................................................ 11 Connectors .............................................................................................................................................. 11 Absolute Maximum Ratings .................................................................................................................... 11 PayRange | BluKey Select™ Reference Manual 6/29/2021 Page 3 | 21 Operating Conditions .............................................................................................................................. 12 ESD handling ratings ............................................................................................................................... 12 RF Specifications ..................................................................................................................................... 13 Connector Pinouts .................................................................................................................................. 13 Mechanical .............................................................................................................................................. 16 Regulatory Approval ................................................................................................................................... 18 Modification statement .......................................................................................................................... 18 United States ..........................................................................…

Text truncated - open the document above for the full version.

Antenna 2402 - 2480 MHz RegulatorSynthesizer 16.000 MHz Xtal BLE CPU 32.768 KHz Xtal I2C EEprom Power from Host UART from MCU PayRange BluKey Pro – Frequency Block Diagram

5/25/2021 PayRange Inc. is requesting original certification for its PayRange BluKey Select (BkSelect), a Bluetooth Low Energy Payment Control Device under 15.247 using FCC ID: 2AF78-01778. The BluKey Select uses the Freescale Coldfire microcontroller and a CSR1010 Bluetooth® SmartSingle-chip μEnergy® radio with integrated microprocessor operating in the 2.400 GHz-2.4835 GHz ISM band. Thank you, Prashant Kanhere Chief Technology Officer

5/17/2021 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 To whom it may concern, We hereby respectfully request that under the provision of 47 CFR 0.459 and 0.457(d) the documents listed below and attached with this application for certification be provided with confidential status. • Schematics • Operational Description Any exhibit / information for which we have requested confidentiality, but which may not be accorded such treatment by the FCC, should be returned to us. The documents listed above contain trade secrets that are treated as confidential by us. Substantial competitive harm to us could result should they be made available to the public. Sincerely, Prashant Kanhere Chief Technology Officer

BluKey Select External Photos

BluKey Select Label and Label Position

BluKey Select Internal Photos Radio Section with Shield frame removed

PRODUCT SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHZ MID SMT Antenna Product Specification SHEET No. F EC No: 637286 1 of 10 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: PS-479480001 Kang Cheng 2020/05/11 Cooper Zhou 2020/05/11 Stary Song 2020/05/11 TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC TITLE 2.4GHZ MID SMT ANTENNA TABLE OF CONTENTS 1.0 SCOPE 2.0 PRODUCT DESCRIPTION 3.0 APPLICABLE DOCUMENTS 4.0 GENERAL SPECIFICATION 5.0 ANTENNA SPECIFICATION 6.0 MECHANICAL REQUIREMENTS 7.0 ENVIRONMENTAL SPECIFICATION 8.0 RECOMMENDED REFLOW CONDITION 9.0 RECOMMENDED FOOTPRINT ON PCB FOR SOLDERING 10.0 PACKING PRODUCT SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHZ MID SMT Antenna Product Specification SHEET No. F EC No: 637286 2 of 10 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: PS-479480001 Kang Cheng 2020/05/11 Cooper Zhou 2020/05/11 Stary Song 2020/05/11 TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC 2.4GHZ MID SMT ANTENNA 1.0 SCOPE This product specification covers the mechanical, electrical and environmental performances specification for 2.4GHz MID SMT antenna. 2.0 PRODUCT DESCRIPTION 2.1 PRODUCT NAME AND SERIES NUMBER (S) Product name: 2.4GHz MID SMT antenna Series Number: 479480001 2.2 DESCRIPTION This is a high-performance antenna implemented using SMD option to meet the customer needs. It has low profile as the size of this antenna. It is designed to cover the frequency 2.4GHz-2.5GHz. 2.3 FEATURES  2.4GHz, monopole,  SMT embedded, PCB corner mounting  High efficiency over 70% on 2.4-2.5GHz  Antenna size 3x4x4mm  RoHS Compliant ANTENNA PICTURE PRODUCT SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHZ MID SMT Antenna Product Specification SHEET No. F EC No: 637286 3 of 10 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: PS-479480001 Kang Cheng 2020/05/11 Cooper Zhou 2020/05/11 Stary Song 2020/05/11 TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC 2.4 PRODUCT STRUCTURE INFORMATION P/N 479480001 MECHANICAL STRUCTURE INFORMATION FOR 479480001 PRODUCT SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHZ MID SMT Antenna Product Specification SHEET No. F EC No: 637286 4 of 10 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: PS-479480001 Kang Cheng 2020/05/11 Cooper Zhou 2020/05/11 Stary Song 2020/05/11 TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC 3.0 APPLICABLE DOCUMENTS DOCUMENT NUMBER DESCRIPTION Sale Drawing (SD) SD-479480001 Mechanical Dimension of the product Application Guide (AS) AS-479480001 Antenna Application and surrounding Packing Drawing (PK) PK-479480001 Product packaging specifications 4.0 GENERAL SPECIFICATION PRODUCT NAME 2.4GHZ MID SMT antenna PART NUMBER 479480001 FREQUENCY RANGE(+/-3MHz) 2.4~2.5GHz POLARIZATION Linear IMPEDANCE WITH MATCHING 50 Ohms OPERATION TEMPERATURE -40°C to 85°C STORAGE TEMPERATURE -40°C to 85°C AVERAGE TOTAL EFFICIENCY >70% RF POWER 2 Watts NET WEIGHT 0.042g/PCS ANTENNA TYPE Plastics *If you plan to re-use the products that be taken out from packaging. Suggest to repacked them within 48 hours by re-seal to prevent oxidation! PRODUCT SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHZ MID SMT Antenna Product Specification SHEET No. F EC No: 637286 5 of 10 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: PS-479480001 Kang Cheng 2020/05/11 Cooper Zhou 2020/05/11 Stary Song 2020/05/11 TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC 5.0 ANTENNA SPECIFICATION All measurements are done of the antenna mounted on reference PCB (100*40*0.8mm Molex p/n:479489001) with VNA Agilent E5071C and Over-The-Air (OTA) chamber. DESCRIPTION EQUIPMENT REQUIREMENT Frequency Range VNA E5071C 2.4~2.5GHz Return Loss VNA E5071C < -6 dB Peak Gain (Max) OTA Chamber 3.7dBi Average Total Efficiency OTA Chamber >70% Polarization OTA Chamber Linear Input Impedance VNA E5071C 50 Ohms Note that the above antenna performance is measured with just the antenna mounted on a recommended PCB to similar a free-space condition. When implement into the system, the frequency resonant might be off-tune due to the loading of surrounding components especially metal plane. This off-tune can be compensated through matching. Although module manufacturers specify a peak gain limit, it is based on free-space conditions. The peak gain will be degraded by 1 to 2dBi in the actual implementation as the radiation pattern will change due to the surround components. As such, during selection of antenna, you can select one with high peak gain to compensate for the loss. Molex can offer assistant to choose the best location and best tuning in-order to meet this peak gain requirement. PRODUCT SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHZ MID SMT Antenna Product Specification SHEET No. F EC No: 637286 6 of 10 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: PS-479480001 Kang Cheng 2020/05/11 Cooper Zhou 2020/05/11 Stary Song 2020/05/11 TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC 6.0 MECHANICAL REQUIREMENTS DESCRIPTION SPECIFICATION Shear Force Apply three axial peeling force on parts soldered on the PCB at the speed rate of 253 mm/minute. Shear force:15N Min. Solder-Ability Test Dip solder pad in flux then immerse in solder bath at 245+/-50°C for 4~5seconds,95% of immersed area mush show no voids 7.0 ENVIRONMENTAL SPECIFICATION DESCRIPTION SPECIFICATION Temperature Cycling Test 1. The device under test is kept for 30 mins in an environment with a temperature of -40 °C. 2. Kept for 4 Hours in an environment with a temperature of 85 degrees. 3. Kept for 2 Hours in an environment with a temperature of 125 degrees. 4. The cycle is repeated until a total of 40 cycles have been completed. Hereafter the conditions are stabilized at room temperature. 5. No cosmetic problem (No bubble issue、No plating peeling off issue、 No mechanical damage.) …

Text truncated - open the document above for the full version.

This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. This Report shall not be reproduced, except in full without written approval of the laboratory. EAR-Controlled Data - This document contains technical data whose export and reexport/retransfer is subject to control by the U.S. Department of Commerce under the Export Administration Act and the Export Administration Regulations. The Department of Commerce’s prior written approval may be required for the export or re- export/retransfer of such technical data to any foreign person, foreign entity or foreign organization whether in the United States or abroad. More: https://www.bis.doc.gov/index.php/forms-documents/regulations-docs/14-commerce-country-chart/fileT PayRange Inc. BKSelect FCC 2.1091:2021 Bluetooth LE Report: PAYR0018.3 CERTIFICATE OF EVALUATION 2018-09-14 Product compliance is the responsibility of the client; therefore, the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. This report reflects only those tests from the referenced standards shown in the certificate of test. It does not include inspection or verification of labels, identification, marking or user information. As indicated in the Statement of Work sent with the quotation, Element’s standard process is to always use the latest published version of the test methods even when earlier versions are cited in the test specification. Issuance of a purchase order was de facto acceptance of this approach. Otherwise, the client would have advised Element in writing of the specific version of the test methods they wanted applied to the subject testing Last Date of Evaluation: Tuesday, June 22, 2021 PayRange Inc. EUT: BKSelect RF Exposure Evaluation Standards Specification Method FCC 1.1307:2021 FCC 1.1307:2021 Results Method Clause Description Applied Results Comments (b)(3)(i)(A) Exemption from RF Exposure Evaluation Yes Pass None Deviations From Evaluation Standards None Approved By: Donald Facteau, Process Architect Report No. PAYR0018.3EAR-Controlled Data2/11 REVISION HISTORY 2018.07.17 Revision Number Description Date (yyyy-mm-dd) Page Number 00 None Report No. PAYR0018.3EAR-Controlled Data3/11 ACCREDITATIONS AND AUTHORIZATIONS 2021.02.26 United States FCC - Designated by the FCC as a Telecommunications Certification Body (TCB). Certification chambers, Open Area Test Sites, and conducted measurement facilities are listed with the FCC. A2LA - Accredited by A2LA to ISO / IEC 17065 as a product certifier. This allows Element to certify transmitters to FCC and IC specifications. NVLAP - Each laboratory is accredited by NVLAP to ISO 17025 Canada ISED - Recognized by Innovation, Science and Economic Development Canada as a Certification Body (CB) and as a CAB for the acceptance of test data. European Union European Commission – Recognized as an EU Notified Body validated for the EMCD and RED Directives. United Kingdom BEIS – Recognized by the UK as an Approved Body under the UK Radio Equipment and UK EMC Regulations. Australia/New Zealand ACMA - Recognized by ACMA as a CAB for the acceptance of test data. Korea MSIT / RRA - Recognized by KCC’s RRA as a CAB for the acceptance of test data. Japan VCCI - Associate Member of the VCCI. Conducted and radiated measurement facilities are registered. Taiwan BSMI – Recognized by BSMI as a CAB for the acceptance of test data. NCC - Recognized by NCC as a CAB for the acceptance of test data. Singapore IDA – Recognized by IDA as a CAB for the acceptance of test data. Israel MOC – Recognized by MOC as a CAB for the acceptance of test data. Hong Kong OFCA – Recognized by OFCA as a CAB for the acceptance of test data. Vietnam MIC – Recognized by MIC as a CAB for the acceptance of test data. SCOPE For details on the Scopes of our Accreditations, please visit: https://www.nwemc.com/emc-testing-accreditations Report No. PAYR0018.3EAR-Controlled Data4/11 FACILITIES 2020.12.15 California Labs OC01-17 41 Tesla Irvine, CA 92618 (949) 861-8918 Minnesota Labs MN01-11 9349 W Broadway Ave. Brooklyn Park, MN 55445 (612)-638-5136 Oregon Labs EV01-12 6775 NE Evergreen Pkwy #400 Hillsboro, OR 97124 (503) 844-4066 Texas Labs TX01-09 3801 E Plano Pkwy Plano, TX 75074 (469) 304-5255 Washington Labs NC01-05 19201 120 th Ave NE Bothell, WA 98011 (425)984-6600 NVLAP NVLAP Lab Code: 200676-0 NVLAP Lab Code: 200881-0 NVLAP Lab Code: 200630-0 NVLAP Lab Code:201049-0 NVLAP Lab Code: 200629-0 Innovation, Science and Economic Development Canada 2834B-1, 2834B-3 2834E-1, 2834E-3 2834D-1 2834G-1 2834F-1 BSMI SL2-IN-E-1154R SL2-IN-E-1152R SL2-IN-E-1017 SL2-IN-E-1158R SL2-IN-E-1153R VCCI A-0029 A-0109 A-0108 A-0201 A-0110 Recognized Phase I CAB for ISED, ACMA, BSMI, IDA, KCC/RRA, MIC, MOC, NCC, OFCA US0158 US0175 US0017 US0191 US0157 Report No. PAYR0018.3EAR-Controlled Data5/11 PRODUCT DESCRIPTION 2018-07-17 Client and Equipment Under Evaluation Information Company Name: PayRange Inc. Address: 9600 NE Cascades Pkwy, Suite 280 City, State, Zip: Portland, OR 97220 Evaluation Requested By: Mike Mitchell EUT: BKSelect Date of Evaluation: Tuesday, June 22, 2021 Information Provided by the Party Requesting the Evaluation Functional Description of the Equipment: Payrange devices allow wireless payment from smartphones to vending and laundry devices with additional interface circuitry for a keypad and a serial interface. Objective: To demonstrate compliance with FCC requirements for RF exposure for 2.1091 mobile/fixed devices The following duty cycle information was provided by Mike Mitchell, Engineer at PayRange, Inc.: PDU A PDU (Protocol Data Unit) is a logical packet that includes all the time transmitting with protocol specific overhead. Ac…

Text truncated - open the document above for the full version.

This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. This Report shall not be reproduced, except in full without written approval of the laboratory. EAR-Controlled Data - This document contains technical data whose export and reexport/retransfer is subject to control by the U.S. Department of Commerce under the Export Administration Act and the Export Administration Regulations. The Department of Commerce’s prior written approval may be required for the export or re- export/retransfer of such technical data to any foreign person, foreign entity or foreign organization whether in the United States or abroad. PayRange Inc. BKSelect FCC 15.247:2021 Report: PAYR0018.1, Issue Date: June 22, 2021 NVLAP LAB CODE: 200630-0 CERTIFICATE OF TEST 2018-09-14 Product compliance is the responsibility of the client; therefore, the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. This report reflects only those tests from the referenced standards shown in the certificate of test. It does not include inspection or verification of labels, identification, marking or user information. As indicated in the Statement of Work sent with the quotation, Element’s standard process is to always use the latest published version of the test methods even when earlier versions are cited in the test specification. Issuance of a purchase order was de facto acceptance of this approach. Otherwise, the client would have advised Element in writing of the specific version of the test methods they wanted applied to the subject testing. Last Date of Test: May 6, 2021 PayRange Inc. EUT: BKSelect Radio Equipment Testing Standards Specification Method FCC 15.247:2021 ANSI C63.10:2013, KDB 558074 Results Method Clause Test Description Applied Results Comments 6.2 Powerline Conducted Emissions Yes Pass 11.6 Duty Cycle Yes Pass 11.8.2 Occupied Bandwidth Yes Pass 11.9.1.1 Output Power Yes Pass 11.9.1.1 Equivalent Isotropic Radiated Power Yes Pass 11.10.2 Power Spectral Density Yes Pass 11.11 Band Edge Compliance Yes Pass 11.11 Spurious Conducted Emissions Yes Pass 11.12.1, 11.13.2, 6.5, 6.6 Spurious Radiated Emissions Yes Pass Deviations From Test Standards None Approved By: Kyle Holgate, Operations Manager Report No. PAYR0018.12/57 REVISION HISTORY 2018.07.17 Revision Number Description Date (yyyy-mm-dd) Page Number 00 None Report No. PAYR0018.13/57 ACCREDITATIONS AND AUTHORIZATIONS 2021.02.26 United States FCC - Designated by the FCC as a Telecommunications Certification Body (TCB). Certification chambers, Open Area Test Sites, and conducted measurement facilities are listed with the FCC. A2LA - Accredited by A2LA to ISO / IEC 17065 as a product certifier. This allows Element to certify transmitters to FCC and IC specifications. NVLAP - Each laboratory is accredited by NVLAP to ISO 17025 Canada ISED - Recognized by Innovation, Science and Economic Development Canada as a Certification Body (CB) and as a CAB for the acceptance of test data. European Union European Commission – Recognized as an EU Notified Body validated for the EMCD and RED Directives. United Kingdom BEIS – Recognized by the UK as an Approved Body under the UK Radio Equipment and UK EMC Regulations. Australia/New Zealand ACMA - Recognized by ACMA as a CAB for the acceptance of test data. Korea MSIT / RRA - Recognized by KCC’s RRA as a CAB for the acceptance of test data. Japan VCCI - Associate Member of the VCCI. Conducted and radiated measurement facilities are registered. Taiwan BSMI – Recognized by BSMI as a CAB for the acceptance of test data. NCC - Recognized by NCC as a CAB for the acceptance of test data. Singapore IDA – Recognized by IDA as a CAB for the acceptance of test data. Israel MOC – Recognized by MOC as a CAB for the acceptance of test data. Hong Kong OFCA – Recognized by OFCA as a CAB for the acceptance of test data. Vietnam MIC – Recognized by MIC as a CAB for the acceptance of test data. SCOPE For details on the Scopes of our Accreditations, please visit: https://www.nwemc.com/emc-testing-accreditations Report No. PAYR0018.14/57 FACILITIES 2020.12.15 California Labs OC01-17 41 Tesla Irvine, CA 92618 (949) 861-8918 Minnesota Labs MN01-11 9349 W Broadway Ave. Brooklyn Park, MN 55445 (612)-638-5136 Oregon Labs EV01-12 6775 NE Evergreen Pkwy #400 Hillsboro, OR 97124 (503) 844-4066 Texas Labs TX01-09 3801 E Plano Pkwy Plano, TX 75074 (469) 304-5255 Washington Labs NC01-05 19201 120 th Ave NE Bothell, WA 98011 (425)984-6600 NVLAP NVLAP Lab Code: 200676-0 NVLAP Lab Code: 200881-0 NVLAP Lab Code: 200630-0 NVLAP Lab Code:201049-0 NVLAP Lab Code: 200629-0 Innovation, Science and Economic Development Canada 2834B-1, 2834B-3 2834E-1, 2834E-3 2834D-1 2834G-1 2834F-1 BSMI SL2-IN-E-1154R SL2-IN-E-1152R SL2-IN-E-1017 SL2-IN-E-1158R SL2-IN-E-1153R VCCI A-0029 A-0109 A-0108 A-0201 A-0110 Recognized Phase I CAB for ISED, ACMA, BSMI, IDA, KCC/RRA, MIC, MOC, NCC, OFCA US0158 US0175 US0017 US0191 US0157 Report No. PAYR0018.15/57 MEASUREMENT UNCERTAINTY TMU.2015.07.10 Measurement Uncertainty When a measurement is made, the result will be different from the true or theoretically correct value. The difference is the result of tolerances in the measurement system that cannot be completely eliminated. To the extent that technology allows us, it has been our aim to minimize this error. Measurement uncertainty is a statistical expression of measurement error qualified by a probability distribution. A measurement uncertainty estimation has been performed for each test per our internal quality document QM205.4.6. The estimation is used to compare the measured result with its "true" or theoretically correct value. The expanded measurement uncert…

Text truncated - open the document above for the full version.

POWERLINE CONDUCTED EMISSIONS WTD.2021.04.01.1 EmiR5 2021.01.08.0 PSA-ESCI 2021.03.17.0 POWERLINE CONDUCTED EMISSIONS WTD.2021.04.01.1 EmiR5 2021.01.08.0 PSA-ESCI 2021.03.17.0 XMit 2020.12.30.0 DirectConnect (1).JPG DirectConnect (2).JPG DIRECT CONNECT Report No. PAYR0018.12/8 XMit 2020.12.30.0 DirectConnect (3).JPG DIRECT CONNECT Report No. PAYR0018.13/8 SPURIOUS RADIATED EMISSIONS WTD.2021.04.01.1 EmiR5 2021.01.08.0 PSA-ESCI 2021.03.17.0 Report No. PAYR0018.14/8 SPURIOUS RADIATED EMISSIONS WTD.2021.04.01.1 EmiR5 2021.01.08.0 PSA-ESCI 2021.03.17.0 Report No. PAYR0018.15/8 SPURIOUS RADIATED EMISSIONS WTD.2021.04.01.1 EmiR5 2021.01.08.0 PSA-ESCI 2021.03.17.0 Report No. PAYR0018.16/8 SPURIOUS RADIATED EMISSIONS WTD.2021.04.01.1 EmiR5 2021.01.08.0 PSA-ESCI 2021.03.17.0 Report No. PAYR0018.17/8