2AF9TMC300Remote transmitter

OPERATIONAL CHECK To check operation, move back a reasonable distance (about 50 ft.) and press the transmitter button. Operation should be reliable at this distance but environment and location of both the transmitter and receiver will affect the range. If the transmitter is stowed well out of sight, it may be necessary to remove it from its mounting and hold near the windshield. Try different locations and positions. If operation is still unsatisfactory, the problem may be isolated by: 1. Checking the door operator. If the door will not open when the wall button is pressed, the problem is likely to be the operator. If the door will open by pressing the wall button, but not when the radio control button is pressed, the problem is probably in the radios. 2. Replacing the transmitter battery. If after performing the above operational checks, the controls still do not function, they should be returned to your dealer for repair or replacement. SUPERSONIC GATE AND DOOR AUTOMATION CO.,LIMITED INSTALLATION INSTRUCTIONS DIGITAL TRANSMITTER MODEL MUC300 Congratulations! You have just purchased a MUC300 Digital Transmitter, which we believe to be the finest product of its kind on the market. With a little care this transmitter should provide you with many years of excellent service. Please take a moment to read the following instructions and you will find that setting your new transmitter will be quite an easy matter. The user can Switch the working frequency between 300MHz and 310MHz by pressing the key(3s) ACCESSING THE CODE SWITCH Insert a small coin into the slot located at the bottom end of the transmitter. Twist the coin and remove the access cover to expose the code switch and battery compartment. SELECTING A CODE You may set your transmitter to any code you desire but be sure that the code you set matches the code that has been set on your radio receiver. The digital code is determined by the positions of the 10 small switches numbered 1 through 10 located in the receiver and transmitter. Any combination of ON (CLOSED) or OFF (OPEN) positions can be selected by using a small screwdriver or ball point pen. (NOTE: The switches are in the “On” position when the side next to the number is pressed in.) In setting your own personal code we strongly urge that several coding schemes be avoided: ALL ON; ALL OFF; 2,4,6,8,10 ON; 1,3,5,7,9 ON. These positions are similar to our or other manufacturer’s test positions, or are frequently used. Once the code has been set, check the operation and replace the hatches. TRANSMITTER INSTALLATION The transmitter is completely self contained, including battery, and can be operated while mounted in the car. It is supplied with a clip for attaching to the sun visor, if desired. If the clip is used attach to the case by sliding it into the recess provided on the back of the transmitter until the small dimples fit into the holes in the clip. TRANSMITTER BATTERY REPLACEMENT Replacement battery - 9 volt NEDA 1604 (Eveready 216 or equivalent). The battery in the transmitter can be checked or changed by removing the front lower half of the transmitter. Refer to the directions under “accessing the code switch” for battery replacement. TO REPLACE OR ADD A SET A replacement or new transmitter or receiver may be purchased by specifying the Model Number and the RF frequency designated on the identification label. The RF frequency is set at the factory and must not be adjusted in the field. The digital code can be matched to the companion receiver or transmitter by following the above procedure. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (current) 4.0 5.0 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0 SUPERSONIC GATE AND DOOR AUTOMATION CO., LIMITED Add: NO.210-1 TAISHAN ROAD CHANGZHOU CITY JIANGSU PROVINCE CHINA Tel: 0519-85132285 Fax: 0519-85132285 2015-11-11 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA FCC ID: 2AF9TMC300 Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, SUPERSONIC GATE AND DOOR AUTOMATION CO., LIMITED hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): (Product description, model name): Remote transmitter , MC300 Sincerely, Client’s name / title : frank king / CEO Contact information / address : NO.210-1 TAISHAN ROAD CHANGZHOU CITY JIANGSU PROVINCE CHINA Tel: 0519-85132285 Fax: 0519-85132285 E-Mail: [email protected]

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 SUPERSONIC GATE AND DOOR AUTOMATION CO., LIMITED Add: NO.210-1 TAISHAN ROAD CHANGZHOU CITY JIANGSU PROVINCE CHINA Tel: 0519-85132285 Fax: 0519-85132285 2015-11-11 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2AF9TMC300 We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Schematics - Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s name / title : frank king / CEO Contact information / address : NO.210-1 TAISHAN ROAD CHANGZHOU CITY JIANGSU PROVINCE CHINA Tel: 0519-85132285 Fax: 0519-85132285 E-Mail: [email protected]

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AF9TMC300 Report No.: LCS1510120400E ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 3 1. EXTERIOR PHOTOGRAPHS Fig.1 Fig.2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AF9TMC300 Report No.: LCS1510120400E ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 3 Fig.3 Fig.4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AF9TMC300 Report No.: LCS1510120400E ________________________________________________________________________________ _________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 3 Fig.5 Fig.6

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD FCC ID: 2AF9TMC300 Report No.: LCS1510120400E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1 LABEL AND LOCATION Size:L:3.0cm*W:2.0cm Remote transmitter Model No.: MC300 FCC ID: 2AF9TMC300 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Label location

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AF9TMC300 Report No.: LCS1510120400E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 35 FCC TEST REPORT For SUPERSONIC GATE AND DOOR AUTOMATION CO.,LIMITED Remote transmitter Model No.: MC300 Additional Model No.: Please refer to page 5. Prepared for : SUPERSONIC GATE AND DOOR AUTOMATION CO.,LIMITED Address : NO.210-1 TAISHAN ROAD CHANGZHOU CITY JIANGSU PROVINCE CHINA Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd. Address : 1/F., Xingyuan Industrial Park, Tongda Road, Bao’an Avenue, Bao’an District, Shenzhen, Guangdong, China Date of receipt of test sample : October 12, 2015 Number of tested samples : 1 Serial number : Prototype Date of Test : October 12, 2015– October 27, 2015 Date of Report : October 27, 2015 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AF9TMC300 Report No.: LCS1510120400E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 2 of 35 FCC TEST REPORT FCC CFR 47 PART 15 C(15.231): 2014 Report Reference No. .............. : LCS1510120400E Date of Issue ................................ : October 27, 2015 Testing Laboratory Name ......... : Shenzhen LCS Compliance Testing Laboratory Ltd. Address ........................................ : 1/F., Xingyuan Industrial Park, Tongda Road, Bao’an Avenue, Bao’an District, Shenzhen, Guangdong, China Testing Location/ Procedure ........ : Full application of Harmonised standards ■ Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name ....................... : SUPERSONIC GATE AND DOOR AUTOMATION CO.,LIMITED Address ........................................ : NO.210-1 TAISHAN ROAD CHANGZHOU CITY JIANGSU PROVINCE CHINA Test Specification Standard ....................................... : FCC CFR 47 PART 15 Subpart C : 2014, ANSI C63.10-2013 Test Report Form No. ................ : LCSEMC-1.0 TRF Originator ............................ : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF .................................. : Dated 2011-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test Item Description. ............... : Remote transmitter Trade Mark .................................. : SUPERSONIC Model/ Type reference ................. : MC300 Ratings ......................................... : DC 9.0V by Battery Result ......................................... : Positive Compiled by: Supervised by: Approved by: Kyle Yin/ File administrators Glin Lu/ Technique principal Gavin Liang/ Manager SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AF9TMC300 Report No.: LCS1510120400E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 3 of 35 FCC--TEST REPORT Type / Model........................... : MC300 EUT......................................... : Remote transmitter Applicant............................... : SUPERSONIC GATE AND DOOR AUTOMATION CO.,LIMITED Address.................................. : NO.210-1 TAISHAN ROAD CHANGZHOU CITY JIANGSU PROVINCE CHINA Telephone............................... : / Fax.......................................... : / Manufacturer........................ : SUPERSONIC GATE AND DOOR AUTOMATION CO.,LIMITED Address................................... : NO.210-1 TAISHAN ROAD CHANGZHOU CITY JIANGSU PROVINCE CHINA Telephone............................... : / Fax.......................................... : / Factory................................... : SUPERSONIC GATE AND DOOR AUTOMATION CO.,LIMITED Address................................... : NO.210-1 TAISHAN ROAD CHANGZHOU CITY JIANGSU PROVINCE CHINA Telephone............................... : / Fax.......................................... : / Test Result Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Test Report No. : LCS1510120400E October 27, 2015 Date of issue SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AF9TMC300 Report No.: LCS1510120400E This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 4 of 35 TABLE OF CONTENTS 1. GENERAL INFORMATION .................................................................................................................................. 5 1.1. DESCRIPTION OF DEVICE (EUT) ........................................................................................................................... 5 1.2. OBJECTIVE ............................................................................................................................................................ 5 1.3. ENVIRONMENTAL CONDITIONS............................................................................................................................. 6 1.4. HOST SYSTEM CONFIGURATION LIST AND DETAILS ............................................................................................. 6 1.5. EXTERNAL I/O PORT ............................................................................................................................................. 6 1.6. EUT OPERATION ...........................................................................................................................…

Text truncated - open the document above for the full version.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AF9TMC300 Report No.:LCS1510120400E _______________________________________________________________________________________________ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.. Page 1 of 1 TEST SETUP PHOTOGRAPHS 1.Photo of Radiated Measurement Below 1G Above 1G