2AF9Z45DEGTX00REMOTE HEAT-TROLLER

Read through all these ins tructions BEFORE start ing (Do not use a Batt ery Tender Harness to Power Heated Clothing!!! ) 1.Turn Off the Vehicle, Generato r or Any Charging source for th e Battery 2.At th e Battery, 3.Attach th e positi ve ring te rminal fr om the battery harness to th e positi ve terminal on th e battery. The positi ve ring terminal can be distinguished fr om th e negati ve by th e fact th at i t has a fu se att ached to th e Wire. Reattach th e bolt to th e battery and tighten. Attach th e negative ring te rminal fr om th e battery harness to th e negati ve te rminal on th e batte ry. The negati ve ring terminal can be disti nguished fr om th e positi ve by th e fact th at i t does NOT have a fu se attached to th e Wire. Reattach th e bolt to the battery and tighten. Secure th e wire harness with cable straps. Be certa in the wire harness and all cords are not pinched. The connecting plug should be easily accessible but clear of all moving parts . Test th e Connection! Plug th e Receiver to th e Batt ery Harness, if you have the “Power In” polarity reversed, then the Red LED will become Non-flashing Yellow in color. CAUTION: It i s possible to overload your charging system by adding too many electrical accessories. If your combined accessories use more electr ica l current than your charging system can produce, th e consumption can discharge th e battery leading to electr ic system damage. Ask your dealer fo r advice. 4. 5. 6. 1. Once you have Synced th e Remote Control, it works just like th e other Heat-trollers. 2. On th e Dual Remote , Turn th e R ED Knob on to sta rt power to th e Liner, Yellow to th e Secondary Ite m. 3. In order to extend th e Remote Control Battery Life, th e L ED only tu rns on when th e switc h is mov ed. It will sta y on for about a second after you move th e switc h, Unless th e battery is getti ng low. In this case, it will double blink after you move th e switch. 4. The Battery should last a season and is replaced by removing th e screws th at hold the lid in place. The batteries are 2 AAA batteries. a. First Disconnect th e Ground (-) Cable fr om th e Battery b. Then Disconnect th e Plus (+) Cable fr om th e Batt ery Instructions for Installing Battery Harness Getti ng the Heat-troller Receiver & Remote to Talk to Each Other Use Instructions for the Remote Control 1. It is easier if you do this befo re installing th e Receiver in the Liner. Make sure the receiver is unplugged fr om Power. Using either Knob, Turn the Remote on and th en off 3 times, 6 clic ks, allowing th e L ED to light between each click. You should end with th e switch in th e Off positi on. (if the switch was turned on/off already at any time and not left on to clear the counter, it can affect the count) The L ED on th e R emote will sta rt double-blinking This mode lasts about 10 sec. If you turn it on/off one more time, it will end the sync mode. While th e Remote is double-blinking, plug in the Receiver to power. You only h ave 10 seconds to plug it to Power while th e LEDs are double Blinking. The units will pair up a uto matically and you wil l know th at th ey are pair ed when th e heat to th e liner sto ps if you left th e switc h in th e off position. Once Synced you should never have to do it again. 2. 3. 4. FCC Warning statement a. for FCC 15b devices (15.105) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‐Reorient or relocate the receiving antenna. ‐Increase the separation between the equipment and receiver. ‐Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐Consult the dealer or an experienced radio/TV technician for help. b. FCC Part 15.21 information for user You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. c. FCC Part 15.19 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation

45deg Electronic Systems 5348 Vegas Drive, #602, Las Vegas, NV 89108 October 26, 2015 Federal Communications Commission Authorization and Evaluation Division FCC ID： 2AF9Z45DEGTX00 Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the applicant hereby requests confidential treatment of information applied this application as outlined below: 1. Block Diagram 2. Circuit Diagram 3. Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application Sincerely, Signature Name/Title: Michael Coan/ Director Company Name: 45deg Electronic Systems Address: 5348 Vegas Drive, #602, Las Vegas, NV 89108 TEL: +17023578664 FAX: Email: [email protected]

45deg Electronic Systems 5348 Vegas Drive, #602, Las Vegas, NV 89108 October 29, 2015 FCC ID：2AF9Z45DEGTX00 Dear Sir, I hereby have entrusted the following person to be a proxy regarding application for Type Certification. Global EMC Standard Tech. Corp. Address: No.3, Baodoucuokeng, Linkou Dist., New Taipei City 244, Taiwan(R.O.C.) Name: Tony Tsai Job Title: Assistant Manger Director Email: [email protected] I am therefore responsible for the contents of the application. Brand Name and Model Name of the specified radio equipment: / FCC ID: 2AF9Z45DEGTX00 Product Name: REMOTE HEAT-TROLLER Signature FCC grantee contact person information. Name/Title: Michael Coan/ Director Company Name: 45deg Electronic Systems Address: 5348 Vegas Drive, #602, Las Vegas, NV 89108 TEL: +17023578664 FAX: Email: [email protected]

Global EMC Standard Tech. Corp. Report No: 1508006R-01 No.3, Baodoucuokeng, Linkou Dist., New Taipei City 244, Taiwan(R.O.C.) Tel:886-2-2603-5321 Fax:886-2-2603-5325 Accredited Lab. of TAF Page 30 of 35 Approved Lab. of TUV, VCCI 8. PHOTOGRAPHS FOR PRODUCT 1. Front View of REMOTE HEAT-TROLLER. 2. Back View of REMOTE HEAT-TROLLER.

Global EMC Standard Tech. Corp. Report No: 1508006R-01 No.3, Baodoucuokeng, Linkou Dist., New Taipei City 244, Taiwan(R.O.C.) Tel:886-2-2603-5321 Fax:886-2-2603-5325 Accredited Lab. of TAF Page 35 of 35 Approved Lab. of TUV, VCCI 10. FCC ID LOCATION 11. Label. REMOTE HEAT-TROLLER Model Number: TX FCC ID: 2AF9Z45DEGTX00

Global EMC Standard Tech. Corp. Report No: 1508006R-01 No.3, Baodoucuokeng, Linkou Dist., New Taipei City 244, Taiwan(R.O.C.) Tel:886-2-2603-5321 Fax:886-2-2603-5325 Accredited Lab. of TAF Page 31 of 35 Approved Lab. of TUV, VCCI 3. Component Side of Mother Board. 4. Solder Side of Mother Board. Global EMC Standard Tech. Corp. Report No: 1508006R-01 No.3, Baodoucuokeng, Linkou Dist., New Taipei City 244, Taiwan(R.O.C.) Tel:886-2-2603-5321 Fax:886-2-2603-5325 Accredited Lab. of TAF Page 32 of 35 Approved Lab. of TUV, VCCI 5. Component Side of Chipset. 6. Component Side of Antenna. Global EMC Standard Tech. Corp. Report No: 1508006R-01 No.3, Baodoucuokeng, Linkou Dist., New Taipei City 244, Taiwan(R.O.C.) Tel:886-2-2603-5321 Fax:886-2-2603-5325 Accredited Lab. of TAF Page 33 of 35 Approved Lab. of TUV, VCCI 7. Inner 8. Inner Global EMC Standard Tech. Corp. Report No: 1508006R-01 No.3, Baodoucuokeng, Linkou Dist., New Taipei City 244, Taiwan(R.O.C.) Tel:886-2-2603-5321 Fax:886-2-2603-5325 Accredited Lab. of TAF Page 34 of 35 Approved Lab. of TUV, VCCI 9. Inner

Global EMC Standard Tech. Corp. Report No: 1508006R-01 No.3, Baodoucuokeng, Linkou Dist., New Taipei City 244, Taiwan(R.O.C.) Tel:886-2-2603-5321 Fax:886-2-2603-5325 Accredited Lab. of TAF Page 1 of 35 Approved Lab. of TUV, VCCI Test Report Application for Certification on Behalf of 45deg Electronic Systems EUT: REMOTE HEAT-TROLLER Model Number: TX FCC ID: 2AF9Z45DEGTX00 Prepared for: 45deg Electronic Systems 348 Vegas Drive, #602, Las Vegas, NV 89108 Report By : Global EMC Standard Tech. Corp. No.3, Baodoucuokeng, Linkou Dist., New Taipei City 244, Taiwan(R.O.C.) Tel : 886-2-2603-5321 Fax : 886-2-2603-5325 1.Test results given in this report only relate to the specimen(s) tested, measured. 2.This report is the property of Global EMC Standard Tech. Corp., and shall not be reproduced, other than in full, without the written consent of Global EMC Standard Tech. Corp. . 3. The client should not use it to claim product endorsement by TAF or any government agencies. 4.All data in this report are traceable to national standard or international standard. Global EMC Standard Tech. Corp. Report No: 1508006R-01 No.3, Baodoucuokeng, Linkou Dist., New Taipei City 244, Taiwan(R.O.C.) Tel:886-2-2603-5321 Fax:886-2-2603-5325 Accredited Lab. of TAF Page 2 of 35 Approved Lab. of TUV, VCCI T A B L E OF C O N T E N T S DESCRIPTION PAGE 1. CERTIFICATION .................................................................................................................................. 3 2. GENERAL INFORMATION .................................................................................................................. 4 2.1 PRODUCTION DESCRIPTION ..............................................................................................................................4 2.2 OPERATIONAL DESCRIPTION ............................................................................................................................5 2.3 TEST MODES & EUT COMPONENTS DESCRIPTION .........................................................................................5 2.4 SUMMARY OF TEST PROCEDURE AND TEST RESULTS .................................................................................5 2.5 CONFIGURATION OF THE TESTED SYSTEM ....................................................................................................6 2.6 LAB AMBIENT .......................................................................................................................................................6 2.7 TEST FACILITY AUTHORIZATION AND ACCREDITATION ................................................................................6 2.8 TEST SETUP .........................................................................................................................................................7 2.9 EUT OPERATING CONDITIONS ..........................................................................................................................7 3. RADIATION EMISSION DATA ............................................................................................................ 8 3.1 TEST EQUIPMENT ...............................................................................................................................................8 3.2 SETUP DIAGRAM .................................................................................................................................................9 3.3 RADIATED EMISSION LIMIT .............................................................................................................................. 10 3.4 TEST CONFIGURATION ..................................................................................................................................... 11 3.5 OPERATING CONDITION OF EUT ..................................................................................................................... 11 3.6 RADIATED EMISSION DATA .............................................................................................................................. 11 3.7 RADIATED EMISSIONS MEASUREMENT RESULTS ........................................................................................ 12 4. BAND EDGE ...................................................................................................................................... 20 4.1 TEST EQUIPMENT ............................................................................................................................................. 20 4.2 BLOCK DIAGRAM OF TEST SETUP .................................................................................................................. 20 4.3 BAND EDGE LIMIT .............................................................................................................................................. 20 4.4 EUT CONFIGURATION ....................................................................................................................................... 21 4.5 OPERATING CONDITION OF EUT ..................................................................................................................... 21 4.6 RADIATED EMISSION DATA .............................................................................................................................. 21 4.7 TEST RELULT ..................................................................................................................................................... 22 5. OCCUPIED BANDWIDTH .................................................................................................................. 24 5.1 TEST EQUIPMENT ............................................................................................................................................. 24 5.2 BLOCK DIAGRAM OF TEST SETUP .................................................................................................................. 24 5.3 LIMIT .....................................................................…

Text truncated - open the document above for the full version.

Global EMC Standard Tech. Corp. Report No: 1508006R-01 No.3, Baodoucuokeng, Linkou Dist., New Taipei City 244, Taiwan(R.O.C.) Tel:886-2-2603-5321 Fax:886-2-2603-5325 Accredited Lab. of TAF Page 28 of 35 Approved Lab. of TUV, VCCI 7. PHOTOGRAPHS FOR TEST 7.1 TEST PHOTOGRAPHS FOR RADIATION 30-1000MHz - Global EMC Standard Tech. Corp. Report No: 1508006R-01 No.3, Baodoucuokeng, Linkou Dist., New Taipei City 244, Taiwan(R.O.C.) Tel:886-2-2603-5321 Fax:886-2-2603-5325 Accredited Lab. of TAF Page 29 of 35 Approved Lab. of TUV, VCCI Above 1GHz -