2AFJ8-CC418W418 MHz Wall Mounted Pull Cord Transmitter

CC-418W TRANSMITTER USERS MANUAL Functional Description: The CC-418W Radio Frequency (RF) transmitter is designed to operate with all Digital Care Systems, Inc. products. The CC- 418W has a large push button labeled “EMERGENCY CALL” and can be manually activated by pressing this button. Activation of the transmitter is via the large button or pulling on the pull-cord. The CC-418W is NOT waterproof and must be kept away from water. Each CC-418W transmits a unique code number and will only activate the receiving device for which it is trained to. Operation: Pressing the “EMERGENCY CALL” button on the front of the unit or pulling on the pull-cord will cause the CC-418W to transmit. The button must be held for at least one half (1/2) second before transmission will begin. This helps prevent accidental activation. Transmission will be indicated by the RED light on the front of the unit and 3 short beeps. The duration of the transmission is limited to a 5 second period, regardless of how long the button is held. The button must be released and pressed again to cause a second transmission. This feature saves battery life while still assuring adequate transmission time to be received by the receiving device. Limited Warranty and Disclaimer: Digital Care Systems Inc. warrants the CC-418W transmitter for a period of three (3) year from the date of purchase to be free from defects in materials and workmanship. Liability shall be limited to the repair or replacement of the equipment. Any consequential damages arising from the use of this product are the sole responsibility of the user. This warranty does not include batteries. Tampering with this equipment will void this warranty and the user’s authority to operate it. This warranty is in lieu of all other expressed warranties, obligations, or liabilities. There are no warranties, which extend beyond the description on the face hereof. ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE WARRANTY PERIOD OF THIS WRITTEN LIMITED WARRANTY. Some states do not allow limitation on how long an implied warranty lasts, so this limitation may not apply to all purchasers. Digital Care Systems, Inc.’s LIABILITY SHALL BE LIMITED TO THE COST OF THE PRODUCT AND IN NO EVENT SHALL Digital Care Systems, Inc. BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR THE INABILITY TO USE THIS PRODUCT OR FOR THE BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, WHATSOEVER. Some states do not allow this exclusion, so this limitation may not apply to all purchasers. FCC Information: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an output on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. - A shielded cable must be used when connecting a peripheral to the serial ports. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference. And (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Digital Care Systems, Inc., 2000C Hartel Ave. Levittown, PA 19057 (215) 946-7700

MET Laboratories, Inc. Safety Certification - EMI - Telecom Environmental Simulation 914 WEST PATAPSCO AVENUE • BALTIMORE, MARYLAND 21230-3432 • PHONE (410) 354-3300 • FAX (410) 354-3313 33439 WESTERN AVENUE • UNION CITY, CALIFORNIA 94587 • PHONE (510) 489-6300 • FAX (510) 489-6372 3162 BELICK STREET • SANTA CLARA, CA 95054 • PHONE (408) 748-3585 • FAX (510) 489-6372 13501 MCCALLEN PASS • AUSTIN, TEXAS 78753 • PHONE (512) 287-2500 • FAX (512) 287-2513 The Nation’s First Licensed Nationally Recognized Testing Laboratory November 11, 2015 Digital Care Systems, Inc. 2000 Hartel Ave., Suite C Levittown, Pennsylvania 19057 Dear Richard Bowman, Enclosed is the EMC Wireless test report for compliance testing of the Digital Care Systems, Inc., CC-418W as tested to the requirements of Title 47 of the CFR, Ch. 1 (10-1-06 ed.), FCC Part 15 Subpart C and RSS-210 Issue 8, December 2010 for Intentional Radiators. Thank you for using the services of MET Laboratories, Inc. If you have any questions regarding these results or if MET can be of further service to you, please feel free to contact me. Sincerely yours, MET LABORATORIES, INC. Jennifer Warnell Documentation Department Reference: (\Digital Care Systems, Inc.\EMC86662B-FCC231 Rev. 1) Certificates and reports shall not be reproduced except in full, without the written permission of MET Laboratories, Inc. . MET Laboratories, Inc. Safety Certification - EMI - Telecom Environmental Simulation 914 WEST PATAPSCO AVENUE • BALTIMORE, MARYLAND 21230-3432 • PHONE (410) 354-3300 • FAX (410) 354-3313 33439 WESTERN AVENUE • UNION CITY, CALIFORNIA 94587 • PHONE (510) 489-6300 • FAX (510) 489-6372 3162 BELICK STREET • SANTA CLARA, CA 95054 • PHONE (408) 748-3585 • FAX (510) 489-6372 13501 MCCALLEN PASS • AUSTIN, TEXAS 78753 • PHONE (512) 287-2500 • FAX (512) 287-2513 MET Report: EMC86662B-FCC231 Rev. 1 © 2015, MET Laboratories, Inc. Page ii of vii Electromagnetic Compatibility Criteria Test Report for the Digital Care Systems, Inc. CC-418W Tested under the FCC Certification Rules contained in Title 47 of the CFR, Part 15.231 Subpart C & RSS-210 for Intentional Radiators MET Report: EMC86662B-FCC231 Rev. 1 November 11, 2015 Prepared For: Digital Care Systems, Inc. 2000 Hartel Ave., Suite C Levittown, Pennsylvania 19057 Prepared By: MET Laboratories, Inc. 914 W. Patapsco Ave Baltimore, MD 21230 Electromagnetic Compatibility Digital Care Systems, Inc. Cover Letter CC-418W CFR Title 47, Part 15.231; RSS-210 MET Report: EMC86662B-FCC231 Rev. 1 © 2015, MET Laboratories, Inc. Page iii of vii Electromagnetic Compatibility Criteria Test Report for the Digital Care Systems, Inc. CC-418W Tested under the FCC Certification Rules contained in Title 47 of the CFR, Part 15.231 Subpart C & RSS-210 for Intentional Radiators Djed Mouada Jennifer Warnell Project Engineer, Electromagnetic Compatibility Lab Documentation Department Engineering Statement: The measurements shown in this report were made in accordance with the procedures indicated, and the emissions from this equipment were found to be within the limits applicable. I assume full responsibility for the accuracy and completeness of these measurements, and for the qualifications of all persons taking them. It is further stated that upon the basis of the measurements made, the equipment tested is capable of operation in accordance with the requirements of FCC Rules Part 15.231 and Industry Canada standard RSS-210 Issue 8, December 2010 under normal use and maintenance. Asad Bajwa Director, Electromagnetic Compatibility Lab Electromagnetic Compatibility Digital Care Systems, Inc. Report Status CC-418W CFR Title 47, Part 15.231; RSS-210 MET Report: EMC86662B-FCC231 Rev. 1 © 2015, MET Laboratories, Inc. Page iv of vii Report Status Sheet Revision Report Date Reason for Revision  September 30, 2015 Initial Issue. 1 November 11, 2015 Engineer corrections. Electromagnetic Compatibility Digital Care Systems, Inc. Table of Contents CC-418W CFR Title 47, Part 15.231; RSS-210 MET Report: EMC86662B-FCC231 Rev. 1 © 2015, MET Laboratories, Inc. Page v of vii Table of Contents I. Executive Summary .................................................................................................................................................1 A. Purpose of Test ...................................................................................................................................................2 B. Executive Summary ............................................................................................................................................2 II. Equipment Configuration .......................................................................................................................................3 A. Overview .............................................................................................................................................................4 B. References ...........................................................................................................................................................5 C. Test Site ..............................................................................................................................................................5 D. Description of Test Sample .................................................................................................................................5 E. Equipment Configuration ....................................................................................................................................5 F. Mode of Operation ..............................................................................................................................................6 G. Monitoring Method .............................................................................................................................................6 H. Modifications ...............................................…

Text truncated - open the document above for the full version.

Photograph 1. Radiated Spurious Emissions, Test Setup, Below 1 GHz Photograph 2. Radiated Spurious Emissions, Test Setup, Above 1 GHz