2AFP2MQ02Cooling Magnetic Wireless Car Charger

Cooling Magnetic Wireless Car Charger User Manual 产品配色与工艺说明图 Product Colour,Material & Finishing Specfications Tolerance 公差 Product Model 产品型号 Part Number 物料编号 Material 材质 Remark 备注 Original Designer 原设计师 Verifing 审核 Date 日期 Color 颜色 Membrane 表面工艺 Dimension 尺寸 Scale 比例 Job No. 图档编码 Revision 版本号 Change Description 版本变更描述 Brand 品牌 Product Type 产品类 Description 描述 MQ02 128g black powder paper (MQ02) 90*65mm POW ERQI 1:1 User Manual 2026.5.11 four color printing ① 取下固定螺帽，将出风口支架套入。 ② 将球头推进车载支架背面圆孔处，顺时针拧紧螺帽固定好 后，可调整车载无线充电器到合适的角度。 ③将车载无线充电器的出风口夹头插入汽车出风口夹片到合适的 位置，拨动固定杠杆，将无线充电器固定在汽车出风口夹片上。 ④将无线充自带的电源线连接车充头并插入汽车点烟器插座。 ⑤ 将带有磁吸无线充电功能的手机放置在车载无线充电器上， 充电板会自动吸附对位同时开始充电。 * 本产品同时支持对不带磁吸功能的无线充电设备进行充电。 FCC警告配件清单 规格参数 安装步骤 1、请勿挤压或碰撞。 2、请勿自行拆卸或投入火中、水中,避免造成短路漏电。 3、请勿在严重高温、潮湿或腐蚀性环境下使用无线充电 器，避免损坏电路出现漏电现象。 4、请勿与带磁条或者芯片的磁卡 (身份证、银行卡等) 放置 太近,避免造成磁卡失效。 5、请保持植入医疗设备 (心脏起搏器、植入性耳蜗等) 与无 线充电器之间的距离至少为20cm,以避免对医疗设备造成潜 在干扰。 6、应看管好儿童,以确保他们不将无线充电器当成玩具来玩, 以避免不必要的意外。 注意事项 * 说明书涉及图片均为示意图， 最终产品以实物为准。 内含：无线充电器、出风口支架、螺帽、车充头、用户手册。 感谢您购买本产品！ 本产品是一款风冷自带线车载手机无线充电器，可充当车 载手机支架并延长手机的续航时间，让您轻松体验数码产品的 无限乐趣。 使用本产品前请认真阅读本手册并妥善保存，以备查阅。 车载无线充电器×1 固定螺帽×1 出风口支架×1 风冷车载磁吸无线充电器 用户手册 车充头×1 输 入: 5V⎓3A, 9V⎓3A, 12V⎓2.92A, 15V⎓2.33A 输出: 25W MAX 工 作频率: 115-205kHz, 360kHz 接收距离: ≤3mm 电力转换: ≥70% 规格尺寸: 66×43×115mm 产 品重量: 120g Input: 5V⎓3A, 9V⎓3A, 12V⎓2.92A, 15V⎓2 .33A Output: 25W MAX Frequency: 115-205kHz, 360kHz Charging distance: ≤3mm Conversion: ≥70% Size: 66×43×115mm N.W.: 120g 1. Do not squeeze or collisions. 2. Do not disassemble or throw into fire or water, to avoid causing a short circuit leakage. 3. Do not use wireless charger in severely hot, humid or corrosive environments, to avoid circuit damage and occurs leakage phenomenon. 4. Do not place too close with magnetic stripe or chip card (ID card, bank cards, etc.) to avoid magnetic failure. 5. Please keep the distance at least 20cm between implantable medical devices (pacemakers, implantable cochlear, etc.) and the wireless chargers, to avoid potential interference with the medical device. 6. To take care of the children, to ensure that they won't play the wireless charger as a toy, to avoid unnecessary accidents. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. 本设备符合FCC规则第15部分。 操作受以下两个条件的约束： (1)本设备不得造成有害干扰； (2)本设备必须接受接收到的任何干扰，包括可能导致意外操作的干 扰。 任何未经合规责任方明确批准的更改或修改都可能导致用户操作设 备的权力失效。 注意：根据FCC规则第15部分，本设备已经过测试，发现符合B类 数字设备的限制。 这些限制旨在提供合理的保护，防止住宅安装中 的有害干扰。 本设备产生、使用并可辐射射频能量，如果未按照说 明安装和使用，可能会对无线电通信造成有害干扰。 但是不能保证 在特定安装中不会发生干扰。 如果本设备确实对无线电或电视接收造成有害干扰, 这可以通过关闭和打开设备来确定，鼓励用户尝试通过以下一个或 多个措施来纠正干扰: --重新定向或重新定位接收天线。 --增加设备和接收器之间的分离。 --将设备连接到与接收器连接的电路不同的电路上的出口。 --咨询经销商或经验丰富的广播/电视技术人员寻求帮助。 FCC辐射暴露声明 该设备符合针对不受控制环境规定的FCC辐射暴露限值。 本设备应 在散热器和您的身体之间的最小距离为20cm的情况下安装和操 作。 ① Remove the fixing nutsert and insert the outlet bracket into place. ② Push the ball head into the circular hole at the back of the vehicle-mounted bracket. Tighten the screw cap clockwise to secure it properly. Then, you can adjust the vehicle-mounted wireless charger to the desired angle. ③ Insert the nozzle clamp of the vehicle-mounted wireless charger into the car nozzle clamp piece to the appropriate position, and then move the fixing lever to fix the wireless charger onto the car nozzle clamp piece. ④ Connect the power cord provided with the wireless charger to the car charger head and insert it into the car's cigarette lighter socket. ⑤ Place the mobile phone with magnetic wireless charging function on the in-car wireless charger. The charging plate will automatically align and start charging simultaneously. * This product also supports charging wireless charging devices that do not have magnetic suction function. NotesFCC WarningList of Accessories Specification Installation steps * All the pictures involved in the manual are schematic diagrams. The final product shall be subject to the actual item. Included: wireless charger, air vent bracket, nutsert, car adapter, user manual. Thank you for purchasing this product! This product is a cooling magnetic wireless car charger with built-in cable. It can serve as a vehicle-mounted mobile phone holder and extend the battery life of the phone, allowing you to enjoy the unlimited fun of digital products with ease. Before using this product, please read this manual carefully and keep it properly for future reference. Wireless car charge…

Text truncated - open the document above for the full version.

1/1 USAgentforServiceofProcessLETTEROFATTESTATION TO: OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USAgentforServiceofProcess: CompanyName:HOPEKCORPORATIONINC Address:16755CoyoteBushDrUnit84,SanDiego,CA92127UnitedStates FRN:0034562900 ContactName:YangyangXu TelephoneNo:(561)875-9826 E-mail:[email protected] ThisletteristoconfirmthattheUSAgentforServiceofProcessacceptsresponsibilitytoactas alocalrepresentativeonbehalfofShenzhenPowerqiTechnologyCo.,Ltd TheUSAgentforServiceofProcessisawareofandagreestocomplywiththerequirements outlinedintheFCCEquipmentAuthorizationProgram,ReportandOrderFCC22-84,andclause §2.911. Applicant: CompanyName:ShenzhenPowerqiTechnologyCo.,Ltd ProductDescription:CoolingMagneticWirelessCarCharger FRN:0024845463 GranteeCode:2AFP2 FCCID:2AFP2MQ02 ContactName:TinaQu Address:Room201,302,401ofA4Building,BlockA,FangxingScienceandTechnologyPark, No.13ofBaonanRoad,LonggangDistrict,Shenzhen,China TelephoneNo:075584522599 E-mail:[email protected] TheApplicantisawareofandagreestocomplywiththerequirementsoutlinedintheFCC EquipmentAuthorizationProgram,ReportandOrderFCC22-84,andclause§2.911. ThisAgreementisvaliduntil(Permanentlyvalid). Date:2026/5/14 Applicant’sName: ShenzhenPowerqiTechnologyCo.,Ltd USAgentforServiceofProcess’sName: HOPEKCORPORATIONINC Title:SalesManagerTitle:Manager SignatureSignature

Rev 1/26/2023 Shenzhen Powerqi Technology Co., Ltd Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Apr. 10, 2026 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2AFP2MQ02 [Shenzhen Powerqi Technology Co., Ltd] certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. [Shenzhen Powerqi Technology Co., Ltd] certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Sincerely, (Applicant signature) (Applicant printed name) Tina Qu Rev 1/26/2023 Shenzhen Powerqi Technology Co., Ltd Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Apr. 10, 2026 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AFP2MQ02 [Shenzhen Powerqi Technology Co., Ltd] certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) Tina Qu

Shenzhen Powerqi Technology Co., Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: May 14, 2026 Subject; Request for Confidentiality FCC ID: 2AFP2MQ02 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Software Security Requirements for UNII devices In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Tina Qu Title: Sales Manager

Effective Date: April 2, 2020 QSF 7.6.4-8 – Agent Authorization Letter Template Page 1 of 1 Revision Date: Revision: 0 Shenzhen Powerqi Technology Co., Ltd Date: Apr. 10, 2026 Product Model Number: MQ02 FCC ID: 2AFP2MQ02 To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following:  Testing  Approval applications and procedures We declare that QAI Laboratories Ltd. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by QAI Laboratories Ltd. on our behalf shall have the same effect as acts of our own. By: Contact Listed on FCC Wesbite Title: Sales Manager Email: [email protected] Telephone: 075584522599 On behalf of: Shenzhen Powerqi Technology Co., Ltd

Ext Photos Model: MQ02 Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6 Photo 7

产品配色与工艺说明图 Product Colour,Material & Finishing Specfications Tolerance 公差 Product Model 产品型号 Part Number 物料编号 Material 材质 Remark 备注 Original Designer 原设计师 Verifing 审核 Date 日期 Color 颜色 Membrane 表面工艺 Dimension 尺寸 Scale 比例 Job No. 图档编码 Revision 版本号 Change Description 版本变更描述 Brand 品牌 Product Type 产品类 Description 描述 1.0 MQ02 POWERQI 1:1 后壳 2026.4.29 Screen-printed PT cold gray 8C Made in China Input: 5V 3A, 9V 3A, 12V 2.92A, 15V 2.33A Output: 25W Max FCCID: 2AFP2MQ02 Cooling Magnetic Wireless Car Charger 12mm Center Black

Int Photos Model: MQ02 Photo 1 Photo 2 ANT Photo 3 Photo 4 Photo 5 Photo 6

- Page 1 of 11 - Report No.: HB20260325001E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com RF EXPOSURE Test Report Product: Cooling Magnetic Wireless Car Charger Trade Mark: POWERQI Model Number: MQ02 FCC ID: 2AFP2MQ02 Prepared for Shenzhen Powerqi Technology Co., Ltd Room 201, 302, 401 of A4 Building, Block A, Fangxing Science and Technology Park, No. 13 of Baonan Road, Longgang District, Shenzhen, China Prepared by Shenzhen HongBiao Certification& Testing Co., Ltd Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen, China Tel.: +86-755-2998 9321 Fax.: +86-755-2998 5110 Website: http://www.sz-hongbiao.com - Page 2 of 11 - Report No.: HB20260325001E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Table of Contents 1 GENERAL DESCRIPTION ................................................................................................................................... 5 1.1 DESCRIPTION OF EUT ................................................................................................................................................ 5 1.2 TEST MODE .............................................................................................................................................................. 5 1.3 TEST SETUP .............................................................................................................................................................. 5 1.4 ANCILLARY EQUIPMENT .............................................................................................................................................. 5 2 TEST FACILITIES AND ACCREDITATIONS ............................................................................................................ 6 2.1 TEST LABORATORY ..................................................................................................................................................... 6 2.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 6 2.3 MEASUREMENT UNCERTAINTY ..................................................................................................................................... 6 2.4 TEST SOFTWARE ........................................................................................................................................................ 6 3 LIST OF TEST EQUIPMENT ................................................................................................................................ 7 4 RF EXPOSURE .................................................................................................................................................. 8 4.1 MAXIMUM PERMISSIBLE EXPOSURE .............................................................................................................................. 8 4.1.1. Limit ............................................................................................................................................................ 8 4.1.2. Test Procedures ........................................................................................................................................... 8 4.1.3. Test Setup .................................................................................................................................................... 8 4.1.4. Test Result ................................................................................................................................................... 8 5 PHOTOGRAPHS OF THE TEST SETUP............................................................................................................... 11 - Page 3 of 11 - Report No.: HB20260325001E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com TEST RESULT CERTIFICATION Applicant’s Name ................. : Shenzhen Powerqi Technology Co., Ltd Address ................................. : Room 201, 302, 401 of A4 Building, Block A, Fangxing Science and Technology Park, No. 13 of Baonan Road, Longgang District, Shenzhen, China Manufacturer's Name .......... : Shenzhen Powerqi Technology Co., Ltd Address ................................. : Room 201, 302, 401 of A4 Building, Block A, Fangxing Science and Technology Park, No. 13 of Baonan Road, Longgang District, Shenzhen, China Product description Product name ........................ : Cooling Magnetic Wireless Car Charger Model Number ....................... : MQ02 Standards ............................. : FCC CFR 47 PART 1 , 1.1310 Test procedure ....................... : KDB 680106 D01 Wireless Power Transfer v04 This device described above has been tested by Shenzhen HongBiao Certification& Testing Co., Ltd and the test results show that the equipment under test (EUT) is in compliance with the EMC requirements. And it is applicable only to the tested sample identified in the report. Date of Test ............................................ : Date (s) of performance of tests ............. : Mar. 25, 2026~Apr. 09, 2026 Test Result ............................................... : Pass Testing Engineer : (Zoe Su) Technical Manager : ( M i n g L i u) Authorized Signatory : (L e o S u) - Page 4 of 11 - Report No.: HB20260325001E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,C…

Text truncated - open the document above for the full version.

Address: No. 138, Gaolong West Road, Gaobu Town, Dongguan City, Guangdong Province Tel：86-076986018114 Fax： 86-076986015646 Http://www.jzcoil.com文件编号FilNo: KC-JZ-09-008 1 DONGGUAN KIMCHEN INDUSTRY INTL LIMITED 产品规格书 PRODUCT SPECIFICATION 拟制 PREPARED BY 跟单员 MERCHANDISER 工程审核 ENGINEER CHECKED BY 批准 APPROVED BY Huang Zhi 客 户：深圳市倍力奇科技有限公司 CUSTOMER:____________________________________________________________________ 客户料号：3-122DX01010AA-168 CUST P/N:____________________________________________________________________ 金赞料号：J30-000986-001 K C P/N:____________________________________________________________________ 产品型号：20.5*39.5*0.08*80P*11TS*17MM D E S E : 日 期：2026.3.10 D A T E :____________________________________________________________________ 版 本：A.0 VERSION :____________________________________________________________________ （客户承认受领印）ACCEPTANCE STAMP 东莞市金赞智能科技有限公司 DONGGUAN KIMCHEN INDUSTRY INTL LIMITED 3-122DX01010AA-168 20.5*39.5*0.08*80P*11TS*17M M 拟制 PREPARED BY 工程审核 ENGINEER CHECKED BY 2 版本 Rev. 变更前 Before Change 变更后内容 DESCRIPTION(Content Or Reason ForChanged) 日期 Date 修订者 Revisor A.0--新发行（Initial Release）2026/3/10 Huang Zhi Huang Zhi Li jing 东莞市金赞智能科技有限公司 DONGGUANKIMCHENINDUSTRYINTL LIMITED 3-122DX01010AA-168 20.5*39.5*0.08*80P*11TS*17M M 拟制 PREPAREDBY 工程审核 ENGINEERCHECKEDBY 3 1. 产品外形尺寸（OVERALLDIMENSIONSOF PRODUCTS): 单位(Unit):毫米(mm) PS:1.(E) Magnetic external lead length; 2. (G) Includes the inlet but excludes the release paper; 3. The inlet point is fixed with white glue. ABCDEFGH 15 ±120.5±0.539.5±0.543.5±0.517±13±12.15±0.15 0.95±0.1 Huang Zhi Li jing 东莞市金赞智能科技有限公司 DONGGUANKIMCHENINDUSTRYINTL LIMITED 3-122DX01010AA-168 20.5*39.5*0.08*80P*11TS*17M M 拟制 PREPAREDBY 工程审核 ENGINEERCHECKEDBY 4 圈数 Turns 线径 WireDia. 绕线方式疏/密 Wdg.Type Spred/Close 绕线方向 Wdg.Direction 相交是/否 Intersect Yes/Not 线圈正/反贴 Coil Positive/AntiPaste 11TS 0.08*80P热风绞线 （Strandedwire） 密绕（Close） 逆时针 （Anticlockwise） 是（Yes） 反贴（Anti/Paste） All materials must meet the ROHS standards. 2. 电气特性（ELECTRICALCHARACTERISTICS): 温度TEMPERATURE:25±10°C,湿度RELATIVEHUMIDITY:65±10% 序号 NO. 项目 ITEM 端子 TERMINAL 标准 SPECIFICATION 测试条件 TESTFREQUENCY 测试仪器 TESTEQUIPMENTS 1INDS-F Coil with magnetic sheet: 7.7uH ± 10% 100kHz/1VLCZ METER1062 2DCRS-F Resistance: 65mΩ (Maximum) /LCZ METER1062 3Q 值S-F Qvalue：60MIN 100kHz/1VLCZ METER1062 3.材料清单（BILLOF MATERIAIS): 序号 NO. 材料名称 Materialname 品名描述 Description 物料代码 MaterialCode 厂商代码 Vendorcode 1 wire rod 0.08 * 80P hot air twisted wire JX-2U-F-0008 CX 2 Large magnetic disk G43.5 ± 0.5 * 5.3 * 0.8 (with holes, with double L- shaped grooves, with a small groove of 3mm in the middle) GCP-T-00298HYT 3 Small magnetic disk Hard magnetic circular shape, 15*0.7H, without holes or grooves GCP-T-00305LX 4 Double-sided adhesive tape 3M Double-sided Adhesive Tape 9448A 42*0.12H With Tear-off Handle SMJ-3M-00077 HWD 5 Small double-sided adhesive tape Round regular double-sided adhesive tape 13*0.08H with tear-off feature SMJ-T-0082HWD Huang zhi Li jing 东莞市金赞智能科技有限公司 DONGGUANKIMCHENINDUSTRYINTL LIMITED 3-122DX01010AA-168 20.5*39.5*0.08*80P*11TS*17M M 拟制 PREPAREDBY 工程审核 ENGINEERCHECKEDBY 5 6 glueJS-E7202 (Thickened) White Adhesive E7202WHZY 7 Tin Environmentally friendly lead-free solder wire Lead-free high-temperature solder wire XC 8 Gold Finger Adhesive Tape 3mm High-temperature adhesive tape 3MM JRM 9 heat shrink tubing ø1.0*14MM // Huang zhi Li jing

- Page 1 of 29 - Report No.: HB20260325001E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Test Report Product: Cooling Magnetic Wireless Car Charger Trade Mark: POWERQI Model Number: MQ02 FCC ID: 2AFP2MQ02 Prepared for Shenzhen Powerqi Technology Co., Ltd Room 201, 302, 401 of A4 Building, Block A, Fangxing Science and Technology Park, No. 13 of Baonan Road, Longgang District, Shenzhen, China Prepared by Shenzhen HongBiao Certification& Testing Co., Ltd Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen, China Tel.: +86-755-2998 9321 Fax.: +86-755-2998 5110 Website: http://www.sz-hongbiao.com - Page 2 of 29 - Report No.: HB20260325001E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Table of Contents 1 GENERAL DESCRIPTION ................................................................................................................................... 5 1.1 DESCRIPTION OF EUT ................................................................................................................................................ 5 1.2 TEST MODE .............................................................................................................................................................. 5 1.3 TEST SETUP .............................................................................................................................................................. 6 1.4 POWER SETTING CONFIGURATION PARAMETERS ............................................................................................................... 6 1.5 ANCILLARY EQUIPMENT .............................................................................................................................................. 6 2 SUMMARY OF TEST RESULT ............................................................................................................................. 7 3 TEST FACILITIES AND ACCREDITATIONS ............................................................................................................ 8 3.1 TEST LABORATORY ..................................................................................................................................................... 8 3.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 8 3.3 MEASUREMENT UNCERTAINTY ..................................................................................................................................... 8 3.4 TEST SOFTWARE ........................................................................................................................................................ 8 4 LIST OF TEST EQUIPMENT .............................................................................................................................. 10 5 TEST ITEM AND RESULTS ............................................................................................................................... 12 5.1 ANTENNA REQUIREMENT .......................................................................................................................................... 12 5.2 CONDUCTED EMISSION ............................................................................................................................................. 13 5.3 RADIATED EMISSION ................................................................................................................................................ 15 5.4 OCCUPIED BANDWIDTH ............................................................................................................................................ 20 6 PHOTOGRAPHS OF THE TEST SETUP............................................................................................................... 22 7 PHOTOGRAPHS OF THE EUT .......................................................................................................................... 23 - Page 3 of 29 - Report No.: HB20260325001E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com TEST RESULT CERTIFICATION Applicant’s Name ................. : Shenzhen Powerqi Technology Co., Ltd Address ................................. : Room 201, 302, 401 of A4 Building, Block A, Fangxing Science and Technology Park, No. 13 of Baonan Road, Longgang District, Shenzhen, China Manufacturer's Name .......... : Shenzhen Powerqi Technology Co., Ltd Address ................................. : Room 201, 302, 401 of A4 Building, Block A, Fangxing Science and Technology Park, No. 13 of Baonan Road, Longgang District, Shenzhen, China Product description Product name ........................ : Cooling Magnetic Wireless Car Charger Model Number ....................... : MQ02 Standards ............................. : FCC Part 15C Test procedure ....................... : IEEE/ANSI C63.10-2020 This device described above has been tested by Shenzhen HongBiao Certification& Testing Co., Ltd and the test results show that the equipment under test (EUT) is in compliance with the EMC requirements. And it is applicable only to the tested sample identified in the report. Date of Test ............................................ : Date (s) of performance of tests ............. : Mar. 25, 2026~Apr. 09, 2026 Test Result ............................................... : Pass Testing Engineer : (Zoe Su) Technical Manager : ( M …

Text truncated - open the document above for the full version.

Photographs of the Test Setup Model: MQ02 Radiated Emission Below 30MHz Radiated Emission Above 30MHz MPE