2AFQJFORM1Form Vibrator

IMPORTANT SAFEGUARDS READ ALL INSTRUCTIONS BEFORE USING. DO NOT DISCARD THESE INSTRUCTIONS. FORM VIBRATORS HAVE BEEN CAREFULLY ENGINEERED FOR BOTH EFFECTIVENESS AND SAFETY. WHEN USING ELECTRICAL PRODUCTS, ESPECIALLY WHEN CHILDREN ARE PRESENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: DANGER In order to reduce risk of electric shock: – DO NOT place or store the charging base in water or other liquid. – DO NOT place or store the charging base where it can fall or be pulled into a bathtub, sink, toilet or other liquid. – DO NOT reach for the charging base if it has fallen into water or other liquid. Unplug immediately. – DO NOT place the vibrator in the charging base when wet. – DO NOT put metal or other conductive materials on the charging base contacts. – ALWAYS unplug the cord from the charging base before cleaning, and ensure that it is dry before plugging it into an electrical outlet. – DO NOT plug the charging base into an incorrect voltage source outlet. It has been designed for use with a specific electrical voltage. Refer to label on the wall plug for the correct voltage specification. Voltage converters and plug adapters do not guarantee voltage compatibility. Never force the plug into an outlet. – DO NOT insert the vibrator into the charging base if the charging base is damaged. – DO NOT use a power adapter other than one provided by Jimmyjane. WARNING To reduce the risk of burns, electrocution, fire or injury: – Never operate the product if it is not working properly, if it has been dropped, is damaged in any way, or if the charging base has been dropped into water, or has a damaged cord or plug. – Do not operate the vibrator if the outer layer of silicone or the metal contacts have been damaged. – Do not mistreat the Lithium Polymer battery if it becomes exposed. – Do not disassemble, crush or puncture the Lithium Polymer battery. Do not allow metal objects to contact the battery terminals. – Do not dispose of either the device or the Lithium Polymer battery in a fire. – Unplug the power adapter from outlet when not in use. – Do not carry the charging base by its power cord or use the cord as a handle. – Always keep the power cord away from heated surfaces. – Always connect charging base to a properly grounded electrical outlet. – This product is designed for household use only. Do not use charging base outdoors. – Vibrator and charging base should never be placed in a dishwasher for cleaning. – The charging base should never be submerged in liquid for cleaning. – Close supervision is necessary when this product is used by, on or near children, invalids or disabled persons. – Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons. – Use this product only for its intended purpose as described in this manual. – Do not use attachments not recommended by Jimmyjane. – Do not leave unattended on any surface while it is operating. – Do not massage abdomen when pain is present or if you are pregnant. – Do not use massager on swollen or inflamed areas or broken skin. – Do not use on unexplained calf pain. – Do not massage any single area for more than 15 minutes. – Never use the product while sleeping. – Always avoid contact with the eye or eyelid. – Do not massage the upper neck area near the base of the skull. – Individuals with pacemakers or other implanted devices should consult a doctor before use. – Do not use this product as a substitute for medical attention. – Do not use on broken or sensitive skin areas or in the presence of poor circulation. – Do not touch the contacts on the charging base with any part of your body. – If you have concerns regarding your health, consult your doctor before using this product. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. WEEE Electrical and electronic equipment (EEE) contains materials, components and substances which can be dangerous to the environment and harmful to human health if waste electrical and electronic equipment (WEEE) is not disposed of correctly. Products labeled with the symbol of a crossed-out wheeled bin as shown above are electrical and electronic equipment. The crossed-out wheeled bin denotes that waste electrical and electronic equipment must not be disposed of with the remainder of unseparated household waste, but should instead be collected separately. All municipalities have established collection schemes to this end. Waste electrical and electronic equipment can be delivered free of charge by any person to recycling stations or to other collection sites, or it can be collected directly from the households. For more detailed information, please refer to your local municipality. As a consumer, you are not allowed to dispose of waste electrical and electr…

Text truncated - open the document above for the full version.

DIAMOND PRODUCT LLC CO. JIMMYJANE Date: Sep.4 th , 2015 Federal Communications Commission Authorization and Evaluation Division FCC ID: 2AFQJFORM1 Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this application as outlined below: 1. Block diagram 2. Schematics 3. Operation Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might to harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentation will not be made before the date of the grant for this application. Sincerely, Name：PETERCAROPELO Title：VP of Creative Development Company name: DIAMOND PRODUCT LLC CO. JIMMYJANE Tel. ：415-864-3474 EXT.328 Fax：415-864-3473 12 EAST SIR FRANCIS DRAKE BLVD. STE B1 LARKSPUR, CA

DIAMOND PRODUCT LLC CO. JIMMYJANE AGENCY AUTHORIZATION LETTER FCC ID: 2AFQJFORM1 Date: Sep. 4 th , 2015 To whom it may concern: We, the undersigned, hereby authorize Bureau Veritas Shenzhen Co. Ltd Dongguan Branch., to act on our behalf, as our agent, in the following matters related to the FCC approval of our products: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out by BVDG within the scope of this authorization shall have the same effects as our own. This authorization shall expire 6 months form original date. If you have any Questions regarding the authorization, please don’t hesitate to contact us. Thank you. Sincerely, Name：PETERCAROPELO Title：VP of Creative Development Company name: DIAMOND PRODUCT LLC CO. JIMMYJANE Tel.：415-864-3474 EXT.328 Fax：415-864-3473 12 EAST SIR FRANCIS DRAKE BLVD. STE B1 LARKSPUR, CA

Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 1 of 3 Report Version 1 Reference No.: 150818N022-1 PHOTOGRAPHS OF THE EUT Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 2 of 3 Report Version 1 Reference No.: 150818N022-1 Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 3 of 3 Report Version 1 Reference No.: 150818N022-1

Location：on the charging connector

Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 1 of 5 Report Version 1 Reference No.: 150818N022-1 PHOTOGRAPHS OF THE EUT Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 2 of 5 Report Version 1 Reference No.: 150818N022-1 Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 3 of 5 Report Version 1 Reference No.: 150818N022-1 Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 4 of 5 Report Version 1 Reference No.: 150818N022-1 ANT Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 5 of 5 Report Version 1 Reference No.: 150818N022-1

Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 1 of 6 Report Version 1 Test Report No.: FS150818N022-1 RF EXPOSURE REPORT Applicant DIAMOND PRODUCT LLC CO. JIMMYJANE Address 12 EAST SIR FRANCIS DRAKE BLVD. STE B1 LARKSPUR, CA Manufacturer or Supplier Sheenway Asia Ltd. Address Room 1313,13/F, Austin Tower, 22-26 Austin Avenue, Tsimshatsui, Hong Kong Product Form Vibrator Brand Name JIMMYJANE Model Form 1 Additional Model & Model Difference N/A Date of tests Aug. 02, 2015 ~ Aug. 28, 2015 FCC Part 2 (Section 2.1091) KDB 447498 D03 IEEE C95.1 CONCLUSION: The submitted sample was found to COMPLY with the test requirement Tested by Blue Zheng Project Engineer / EMC Department Approved by Chris Chen Assistant Manager / EMC Department Date: Aug. 28, 2015 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 2 of 6 Report Version 1 Test Report No.: FS150818N022-1 Table of Contents RELEASE CONTROL RECORD ................................................................................ 3 1. CERTIFICATION .............................................................................................. 4 2. RF EXPOSURE DEFINE ................................................................................. 5 3. CLASSIFICATION ........................................................................................... 5 4. SAR TEST EXCLUSION THRESHOLDS ........................................................ 6 Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 3 of 6 Report Version 1 Test Report No.: FS150818N022-1 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED FS150818N022-1 Original release Aug. 28, 2015 Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 4 of 6 Report Version 1 Test Report No.: FS150818N022-1 1. CERTIFICATION FCC ID: 2AFQJFORM1 PRODUCT: Form Vibrator BRAND NAME: JIMMYJANE MODEL NO.: Form 1 ADDITIONAL NO.: N/A TEST SAMPLE: Engineering Sample APPLICANT: 12 EAST SIR FRANCIS DRAKE BLVD. STE B1 LARKSPUR, CA STANDARDS: FCC Part 2 (Section 2.1091) KDB 447498 D03 IEEE C95.1 Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 5 of 6 Report Version 1 Test Report No.: FS150818N022-1 2. RF EXPOSURE DEFINE The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,16 where
 f(GHz) is the RF channel transmit frequency in GHz
 Power and distance are rounded to the nearest mW and mm before calculation
 The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·( f(MHz)/150)] mW, at 100MHz to 1500 MHz b) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW at > 1500 MHz and ≤ 6 GHz 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by ½ for test separation distances ≤ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When…

Text truncated - open the document above for the full version.

Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 1 of 36 Report Version 1 Test Report No.: RF150818N022-1 TEST REPORT Applicant DIAMOND PRODUCT LLC CO. JIMMYJANE Address 12 EAST SIR FRANCIS DRAKE BLVD. STE B1 LARKSPUR, CA Manufacturer or Supplier Sheenway Asia Ltd. Address Room 1313, 13/F, Austin Tower, 22-26 Austin Avenue, Tsimshatsui, Hong Kong Product Form Vibrator Brand Name JIMMYJANE Model Form 1 Additional Model & Model Difference N/A Date of tests Aug. 02, 2015 ~ Aug. 28, 2015 the tests have been carried out according to the requirements of the following standard: FCC Part 15, Subpart C, Section 15.247 CONCLUSION: The submitted sample was found to COMPLY with the test requirement Tested by Blue Zheng Project Engineer/ EMC Department Approved by Chris Chen Assistant Manager/ EMC Department Date: Aug. 28, 2015 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 2 of 36 Report Version 1 Test Report No.: RF150818N022-1 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................................ 4 1 SUMMARY OF TEST RESULTS .................................................................................................... 5 2 MEASUREMENT UNCERTAINTY ............................................................................................... 5 3 GENERAL INFORMATION ............................................................................................................ 6 3.1 GENERAL DESCRIPTION OF EUT............................................................................................. 6 3.2 DESCRIPTION OF TEST MODES............................................................................................... 7 3.2.1. CONFIGURATION OF SYSTEM UNDER TEST ............................................................... 7 3.2.2. TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .................................... 7 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................................ 10 3.4 DESCRIPTION OF SUPPORT UNITS ....................................................................................... 10 4 TEST TYPES AND RESULTS .......................................................................................................11 4.1 CONDUCTED EMISSION MEASUREMENT .............................................................................. 11 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ................................................ 11 4.1.2 TEST INSTRUMENTS ...................................................................................................... 11 4.1.3 TEST PROCEDURES ..................................................................................................... 12 4.1.4 DEVIATION FROM TEST STANDARD ........................................................................... 12 4.1.5 TEST SETUP ................................................................................................................... 13 4.1.6 EUT OPERATING CONDITIONS .................................................................................... 13 4.1.7 TEST RESULTS .............................................................................................................. 14 4.2 RADIATED EMISSION MEASUREMENT .................................................................................. 16 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT .................................................... 16 4.2.2 TEST INSTRUMENTS ..................................................................................................... 17 4.2.3 TEST PROCEDURES ..................................................................................................... 18 4.2.4 DEVIATION FROM TEST STANDARD ........................................................................... 18 4.2.5 TEST SETUP ................................................................................................................... 19 4.2.6 EUT OPERATING CONDITIONS .................................................................................... 19 4.2.7 TEST RESULTS .............................................................................................................. 20 4.3 6DB BANDWIDTH MEASUREMENT ...............................................................................…

Text truncated - open the document above for the full version.

Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 1 of 2 Report Version 1 Reference No.: 150818N022-1 SET-UP FOR CONDUCTED EMISSION TEST Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 2 of 2 Report Version 1 Reference No.: 150818N022-1 SET-UP FOR RADIATED EMISSION TEST Frequency Range< 30MHz~1GHz > Frequency Range< Above 1GHz >