2AFZZCRP4CGTablet Computer

Xiaomi Communications Co., Ltd. Xiaomi Communications Co., Ltd. attests that this client device, FCC ID: 2AFZZCRP4CG, FCC ID: 2AFZZ1RPADG complies with device protocol requirements and operational restrictions: for indoor client 6XD 1. The device will only associate and connect with a low-power indoor access point or subordinate device and never directly connect to other client devices. 2. This device will always initiate transmission under the control of a low-power indoor AP or subordinate except for brief transmissions before joining a network. These short messages will only occur if the client has detected an indoor AP or subordinate operating on a channel. These brief messages will have a time-out mechanism such that if it does not receive a response from an AP it will not continually repeat the request. 3. Transmissions will be lower or equal to the power advertised by the indoor low-power access point or subordinate and never above the maximum output power allowed by the FCC grant for equipment class 6XD. 4. Prohibited for control of or communications with unmanned aircraft systems, including drones. Contact Person: qingyao zeng E-mail: [email protected]

Xiaomi Communications Co., Ltd. September 14, 2024 Attestation We, Xiaomi Communications Co., Ltd. , attest the followings for our device FCC ID: 2AFZZCRP4CG. FCC ID: 2AFZZ1RPADG a. The equipment only punctures to optimize network performance and never to avoid licensed Incumbents. b. If a licensed incumbent is detected, the equipment will use bandwidth reduction for avoidance. c. If a channel is punctured in order to optimize network performance, it will continue to use CBP in the punctured region. __________________ qingyao zeng [email protected]

Xiaomi Communications Co., Ltd. Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Date: September 14, 2024 Subject: Certifications concerning “covered” equipment pursuant to Part 2.911(d)(5)(i) and (ii) To whom it may concern, Xiaomi Communications Co., Ltd. certifies that the equipment FCC ID: 2AFZZCRP4CG. FCC ID: 2AFZZ1RPADG for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Xiaomi Communications Co., Ltd. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List ( as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, ________________________ Name: qingyao zeng Title: N/A E-mail: [email protected]

Xiaomi Communications Co., Ltd. Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Date: September 14, 2024 Subject: Certifications concerning “covered” equipment pursuant to Part 2.911(d)(5)(i) and (ii) To whom it may concern, Xiaomi Communications Co., Ltd. certifies that the equipment FCC ID: 2AFZZCRP4CG. FCC ID: 2AFZZ1RPADG for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Xiaomi Communications Co., Ltd. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List ( as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, ________________________ Name: qingyao zeng Title: N/A E-mail: [email protected]

Rev. 1/1/03 Xiaomi Communications Co., Ltd. Tel: 010 6060 6666 Date: September 14, 2024 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AFZZCRP4CG. FCC ID: 2AFZZ1RPADG Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Schematics Block Diagram Parts List Operation Description Tune up Procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, ________________________ Contact Person: qingyao zeng E-mail: [email protected]

Xiaomi Communications Co., Ltd. Date: September 14, 2024 Power of Attorney To whom it may concern, Please be notified that I, qingyao zeng, have designated Jim Tsai in Sporton International Inc. as the person being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Jim Tsai in Sporton International Inc., on the matters of relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002 (b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C 862. This authorization is limited to the product of as following: FCC ID: 2AFZZCRP4CG. FCC ID: 2AFZZ1RPADG If you have any acknowledgement and response, please send it to Sporton International Inc. directly. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely yours, ____ Contact Person: qingyao zeng E-mail: [email protected]

1/1 Xiaomi Communications Co., Ltd. Date: September 14, 2024 Federal Communications Commission Authorization and Evaluation Division RE : Certification Application FCC ID: 2AFZZCRP4CG. FCC ID: 2AFZZ1RPADG To Whom It May Concern, Pursuant to sections 0.457 and 0.459 of CFR 47, Public Notice DA 04-1705 of the Commission’s policy and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 180 days:  External Photos  Internal Photos  Test set-up photos  Users Manual The application contains technical information, which Xiaomi Communications Co., Ltd. deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application Sincerely, ____ Contact Person: qingyao zeng E-mail: [email protected]

FCC E-Label Information A. Images of the e-label screen are provided below: B. Access to the required information on the e-label Users are able to access the information in no more than three steps in a device’s menu. The actual steps are: Settings > About phone > Certification, or open Settings and type “Certification” into the search bar No any special accessories, access codes, or SIM card are required to go through the above steps. C. Devices have physical labels at point of marketing/sale visible to the purchaser (or in the alternative, on the packaging), and at time of importation? At the time of importation, marketing, and sale, the device will have the required physical label on the packaging, which will include the device’s FCC ID. D. Electronic labeling information is programmed into the device by the manufacturer at the time of manufacture. Yes. E. Electronic labeling information not modifiable by any third party. The e-label of the device is programmed by the grantee and secured in such a manner that it cannot be modified by third parties. F. All the applicable regulatory information required on the packaging or user instructions is provided according to the rules. Applicable regulatory information not found in the e-label is contained in the user manual.

Sporton International Inc. (Shenzhen) Page 1 of 38 TEL : +86-755-86379589 / FAX : +86-755-86379595 Issued Date : Sep. 13, 2024 FCC ID : 2AFZZCRP4CG FCC SAR Test Report Report No. : FA480804 FCC SAR Test Report Applicant : Xiaomi Communications Co., Ltd. Equipment : Tablet Computer Brand Name : Xiaomi Model Name : 2410CRP4CG FCC ID : 2AFZZCRP4CG Standard : FCC 47 CFR Part 2 (2.1093) We, Sporton International Inc. (Shenzhen), would like to declare that the tested sample has been evaluated in accordance with the test procedures given in 47 CFR Part 2.1093 and FCC KDB and has been in compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of Sporton International Inc. (Shenzhen), the test report shall not be reproduced except in full. Approved by: Si Zhang Sporton International Inc. (Shenzhen) 1/F, 2/F, Bldg 5, Shiling Industrial Zone, Xinwei Village, Xili, Nanshan, Shenzhen, 518055 People’s Republic of China Sporton International Inc. (Shenzhen) Page 2 of 38 TEL : +86-755-86379589 / FAX : +86-755-86379595 Issued Date : Sep. 13, 2024 FCC ID : 2AFZZCRP4CG FCC SAR Test Report Report No. : FA480804 Table of Contents 1. Statement of Compliance ............................................................................................................................................. 4 2. Administration Data ...................................................................................................................................................... 5 3. Guidance Applied .......................................................................................................................................................... 5 4. Equipment Under Test (EUT) Information ................................................................................................................... 6 4.1 General Information ............................................................................................................................................... 6 5. Proximity Sensor Triggering Test ................................................................................................................................ 7 6. RF Exposure Limits......................................................................................................................................................10 6.1 Uncontrolled Environment .....................................................................................................................................10 6.2 Controlled Environment .........................................................................................................................................10 6.3 RF Exposure limit for below 6GHz ........................................................................................................................10 6.4 RF Exposure limit for above 6GHz ........................................................................................................................ 11 7. Specific Absorption Rate (SAR) ..................................................................................................................................12 7.1 Introduction ...........................................................................................................................................................12 7.2 SAR Definition .......................................................................................................................................................12 8. System Description and Setup ...................................................................................................................................13 8.1 E-Field Probe ........................................................................................................................................................14 8.2 Data Acquisition Electronics (DAE) .......................................................................................................................14 8.3 Phantom ................................................................................................................................................................15 8.4 Device Holder........................................................................................................................................................16 9. Measurement Procedures ...........................................................................................................................................17 9.1 Spatial Peak SAR Evaluation ................................................................................................................................17 9.2 Power Reference Measurement............................................................................................................................18 9.3 Area Scan .............................................................................................................................................................18 9.4 Zoom Scan ............................................................................................................................................................19 9.5 Volume Scan Procedures ......................................................................................................................................19 9.6 Power Drift Monitoring ...........................................................................................................................................19 10. Test Equipment List ...................................................................................................................................................20 11. SAR System Verification ...........................................................................................................................................21 11.1 Tissue Simulating Liquids ..................…

Text truncated - open the document above for the full version.

Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2024/8/15 System Check_2450MHz DUT: D2450V2-SN:924 Communication System: UID 0, CW; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium: HSL_2450 Medium parameters used: f = 2450 MHz; σ = 1.815 S/m; ε r = 37.601; ρ = 1000 kg/m 3 Ambient Temperature：23.5 °C; Liquid Temperature：22.5 °C DASY5 Configuration: - Probe: EX3DV4 - SN7641; ConvF(7.81, 7.71, 7.62); Calibrated: 2024/6/3 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1664; Calibrated: 2024/7/10 - Phantom: ELI V5.0; Type: QD OVA 002 AA; Serial: TP:1233 - Measurement SW: DASY52, Version 52.10 (3); SEMCAD X Version 14.6.13 (7474) Pin=250mW/Area Scan (81x81x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Maximum value of SAR (interpolated) = 19.2 W/kg Pin=250mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 66.69 V/m; Power Drift = 0.04 dB Peak SAR (extrapolated) = 14.6 W/kg SAR(1 g) = 13.7 W/kg; SAR(10 g) = 6.31 W/kg Smallest distance from peaks to all points 3 dB below = 9 mm Ratio of SAR at M2 to SAR at M1 = 48.9% Maximum value of SAR (measured) = 18.9 W/kg 0 dB = 18.9 W/kg = 17.7 dBW/kg Appendix AReport No. : FA480804 Page: 1/10 Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2024/8/19 System Check_2450MHz DUT: D2450V2-SN:924 Communication System: UID 0, CW; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium: HSL_2450 Medium parameters used: f = 2450 MHz; σ = 1.866 S/m; ε r = 37.65; ρ = 1000 kg/m 3 Ambient Temperature：23.4 °C; Liquid Temperature：22.4 °C DASY5 Configuration: - Probe: EX3DV4 - SN7641; ConvF(7.81, 7.71, 7.62); Calibrated: 2024/6/3 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1664; Calibrated: 2024/7/10 - Phantom: ELI V5.0; Type: QD OVA 002 AA; Serial: TP:1233 - Measurement SW: DASY52, Version 52.10 (3); SEMCAD X Version 14.6.13 (7474) Pin=250mW/Area Scan (81x81x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Maximum value of SAR (interpolated) = 18.9 W/kg Pin=250mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 68.80 V/m; Power Drift = 0.06 dB Peak SAR (extrapolated) = 15.6 W/kg SAR(1 g) = 13.6 W/kg; SAR(10 g) = 6.4 W/kg Smallest distance from peaks to all points 3 dB below = 9.1 mm Ratio of SAR at M2 to SAR at M1 = 49% Maximum value of SAR (measured) = 18.8 W/kg 0 dB = 18.8 W/kg = 17.7 dBW/kg Appendix AReport No. : FA480804 Page: 2/10 Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2024/8/16 System Check_5250MHz DUT: D5GHzV2-SN:1341 Communication System: UID 0, CW; Frequency: 5250 MHz;Duty Cycle: 1:1 Medium: HSL_5250 Medium parameters used: f = 5250 MHz; σ = 4.583 S/m; ε r = 36.663; ρ = 1000 kg/m 3 Ambient Temperature：23.5 °C; Liquid Temperature：22.6 °C DASY5 Configuration: - Probe: EX3DV4 - SN7641; ConvF(6.15, 6.08, 6.01); Calibrated: 2024/6/3 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1664; Calibrated: 2024/7/10 - Phantom: ELI V5.0; Type: QD OVA 002 AA; Serial: TP:1233 - Measurement SW: DASY52, Version 52.10 (3); SEMCAD X Version 14.6.13 (7474) Pin=100mW/Area Scan (71x71x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 15.7 W/kg Pin=100mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 41.10 V/m; Power Drift = 0.12 dB Peak SAR (extrapolated) = 19.5 W/kg SAR(1 g) = 8.47 W/kg; SAR(10 g) = 2.27 W/kg Smallest distance from peaks to all points 3 dB below = 7.2 mm Ratio of SAR at M2 to SAR at M1 = 62.4% Maximum value of SAR (measured) = 15.9 W/kg 0 dB = 15.9 W/kg = 12.37 dBW/kg Appendix AReport No. : FA480804 Page: 3/10 Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2024/8/20 System Check_5250MHz DUT: D5GHzV2-SN:1341 Communication System: UID 0, CW; Frequency: 5250 MHz;Duty Cycle: 1:1 Medium: HSL_5250 Medium parameters used: f = 5250 MHz; σ = 4.479 S/m; ε r = 35.535; ρ = 1000 kg/m 3 Ambient Temperature：23.6 °C; Liquid Temperature：22.4 °C DASY5 Configuration: - Probe: EX3DV4 - SN7641; ConvF(6.15, 6.08, 6.01); Calibrated: 2024/6/3 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1664; Calibrated: 2024/7/10 - Phantom: ELI V5.0; Type: QD OVA 002 AA; Serial: TP:1233 - Measurement SW: DASY52, Version 52.10 (3); SEMCAD X Version 14.6.13 (7474) Pin=100mW/Area Scan (71x71x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 20.8 W/kg Pin=100mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 81.66 V/m; Power Drift = -0.12 dB Peak SAR (extrapolated) = 24.8 W/kg SAR(1 g) = 8.48 W/kg; SAR(10 g) = 2.26 W/kg Smallest distance from peaks to all points 3 dB below = 7.4 mm Ratio of SAR at M2 to SAR at M1 = 62% Maximum value of SAR (measured) = 21.2 W/kg 0 dB = 21.2 W/kg = 20.49 dBW/kg Appendix AReport No. : FA480804 Page: 4/10 Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2024/8/17 System Check_5600MHz DUT: D5GHzV2-SN:1341 Communication System: UID 0, CW; Frequency: 5600 MHz;Duty Cycle: 1:1 Medium: HSL_5600 Medium parameters used: f = 5600 MHz; σ = 4.913 S/m; ε r = 37.082; ρ = 1000 kg/m 3 Ambient Temperature：23.7 °C; Liquid Temperature：22.5 °C DASY5 Configuration: - Probe: EX3DV4 - SN7641; ConvF(5.5, 5.44, 5.37); Calibrated: 2024/6/3 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1664; Calibrated: 2024/7/10 - Phantom: ELI V5.0; Type: QD OVA 002 AA; Serial: TP:1233 - Measurement SW: DASY52, Version 52.10 (3); SEMCAD X Version 14.6.13 (7474) Pin=100mW/Area Scan (71x71x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 15.3 W/kg Pin=100mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 72.23 V/m; Power Drift = -0.05 dB Peak SAR (extrapolated) = 23.5 W/kg SAR(1 g) = 7.96 W/kg; SAR(10 g) = 2.35 W/kg Smallest distance from peaks to all points 3 dB below = 7.4 mm…

Text truncated - open the document above for the full version.

Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2024/8/15 01_Bluetooth_DH5 1Mbps_Bottom Face_0mm_Ch0 Communication System: UID 0, Bluetooth (0); Frequency: 2402 MHz;Duty Cycle: 1:1.304 Medium: HSL_2450 Medium parameters used: f = 2402 MHz; σ = 1.783 S/m; ε r = 40.047; ρ = 1000 kg/m 3 Ambient Temperature：23.5 °C; Liquid Temperature：22.5 °C DASY5 Configuration: - Probe: EX3DV4 - SN7641; ConvF(7.81, 7.71, 7.62); Calibrated: 2024/6/3 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1664; Calibrated: 2024/7/10 - Phantom: ELI V5.0; Type: QD OVA 002 AA; Serial: TP:1233 - Measurement SW: DASY52, Version 52.10 (3); SEMCAD X Version 14.6.13 (7474) Area Scan (101x101x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Maximum value of SAR (interpolated) = 1.00 W/kg Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 0 V/m; Power Drift = 0.00 dB Peak SAR (extrapolated) = 1.67 W/kg SAR(1 g) = 0.618 W/kg; SAR(10 g) = 0.215 W/kg Smallest distance from peaks to all points 3 dB below = 5.5 mm Ratio of SAR at M2 to SAR at M1 = 42.3% Maximum value of SAR (measured) = 1.25 W/kg 0 dB = 1.25 W/kg = 0.97 dBW/kg Appendix BReport No. : FA480804 Page: 1/7 Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2024/8/15 02_WLAN2.4GHz_802.11b 1Mbps_Bottom Face_0mm_Ch1 Communication System: UID 0, WIFI (0); Frequency: 2412 MHz;Duty Cycle: 1:1.022 Medium: HSL_2450 Medium parameters used: f = 2412 MHz; σ = 1.79 S/m; ε r = 40.035; ρ = 1000 kg/m 3 Ambient Temperature：23.5 °C; Liquid Temperature：22.5 °C DASY5 Configuration: - Probe: EX3DV4 - SN7641; ConvF(7.81, 7.71, 7.62); Calibrated: 2024/6/3 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1664; Calibrated: 2024/7/10 - Phantom: ELI V5.0; Type: QD OVA 002 AA; Serial: TP:1233 - Measurement SW: DASY52, Version 52.10 (3); SEMCAD X Version 14.6.13 (7474) Area Scan (101x101x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Maximum value of SAR (interpolated) = 1.73 W/kg Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 0 V/m; Power Drift = 0.00 dB Peak SAR (extrapolated) = 2.25 W/kg SAR(1 g) = 0.828 W/kg; SAR(10 g) = 0.289 W/kg Smallest distance from peaks to all points 3 dB below = 5.7 mm Ratio of SAR at M2 to SAR at M1 = 41.9% Maximum value of SAR (measured) = 1.69 W/kg 0 dB = 1.69 W/kg = 2.28 dBW/kg Appendix BReport No. : FA480804 Page: 2/7 Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2024/8/16 03_WLAN5GHz_802.11a 6Mbps_Edge 1_0mm_Ch60 Communication System: UID 0, WIFI (0); Frequency: 5300 MHz;Duty Cycle: 1:1.053 Medium: HSL_5250 Medium parameters used: f = 5300 MHz; σ = 4.573 S/m; ε r = 35.384; ρ = 1000 kg/m 3 Ambient Temperature：23.5 °C; Liquid Temperature：22.6 °C DASY5 Configuration: - Probe: EX3DV4 - SN7641; ConvF(6.15, 6.08, 6.01); Calibrated: 2024/6/3 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1664; Calibrated: 2024/7/10 - Phantom: ELI V5.0; Type: QD OVA 002 AA; Serial: TP:1233 - Measurement SW: DASY52, Version 52.10 (3); SEMCAD X Version 14.6.13 (7474) Area Scan (51x281x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 2.25 W/kg Zoom Scan (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 0 V/m; Power Drift = -0.13 dB Peak SAR (extrapolated) = 3.69 W/kg SAR(1 g) = 0.834 W/kg; SAR(10 g) = 0.262 W/kg Smallest distance from peaks to all points 3 dB below = 6.4 mm Ratio of SAR at M2 to SAR at M1 = 61.1% Maximum value of SAR (measured) = 2.06 W/kg 0 dB = 2.06 W/kg = 3.14 dBW/kg Appendix BReport No. : FA480804 Page: 3/7 Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2024/8/17 04_WLAN5GHz_802.11ac-VHT160 MCS0_Bottom Face_0mm_Ch114 Communication System: UID 0, WIFI (0); Frequency: 5570 MHz;Duty Cycle: 1:1 Medium: HSL_5600 Medium parameters used: f = 5570 MHz; σ = 4.926 S/m; ε r = 37.097; ρ = 1000 kg/m 3 Ambient Temperature：23.7 °C; Liquid Temperature：22.5 °C DASY5 Configuration: - Probe: EX3DV4 - SN7641; ConvF(5.5, 5.44, 5.37); Calibrated: 2024/6/3 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1664; Calibrated: 2024/7/10 - Phantom: ELI V5.0; Type: QD OVA 002 AA; Serial: TP:1233 - Measurement SW: DASY52, Version 52.10 (3); SEMCAD X Version 14.6.13 (7474) Area Scan (121x121x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 2.12 W/kg Zoom Scan (9x9x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 0 V/m; Power Drift = 0.00 dB Peak SAR (extrapolated) = 4.17 W/kg SAR(1 g) = 0.813 W/kg; SAR(10 g) = 0.150 W/kg Smallest distance from peaks to all points 3 dB below = 5.1 mm Ratio of SAR at M2 to SAR at M1 = 63.2% Maximum value of SAR (measured) = 2.38 W/kg 0 dB = 2.38 W/kg = 3.77 dBW/kg Appendix BReport No. : FA480804 Page: 4/7 Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2024/8/18 05_WLAN5GHz_802.11ac-VHT80 MCS0_Edge 1_0mm_Ch155 Communication System: UID 0, WIFI (0); Frequency: 5755 MHz;Duty Cycle: 1:1 Medium: HSL_5750 Medium parameters used: f = 5755 MHz; σ = 5.071 S/m; ε r = 36.591; ρ = 1000 kg/m 3 Ambient Temperature：23.6 °C; Liquid Temperature：22.9 °C DASY5 Configuration: - Probe: EX3DV4 - SN7641; ConvF(5.47, 5.41, 5.34); Calibrated: 2024/6/3 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1664; Calibrated: 2024/7/10 - Phantom: ELI V5.0; Type: QD OVA 002 AA; Serial: TP:1233 - Measurement SW: DASY52, Version 52.10 (3); SEMCAD X Version 14.6.13 (7474) Area Scan (51x281x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 2.39 W/kg Zoom Scan (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 0.7840 V/m; Power Drift = 0.05 dB Peak SAR (extrapolated) = 4.40 W/kg SAR(1 g) = 0.825 W/kg; SAR(10 g) = 0.250 W/kg Smallest distance from peaks to all points 3 dB below = 4.8 mm Ratio of SAR at M2 t…

Text truncated - open the document above for the full version.

Appendix C Report No. : FA480804 Page: 1/78 Appendix C Report No. : FA480804 Page: 2/78 Appendix C Report No. : FA480804 Page: 3/78 Appendix C Report No. : FA480804 Page: 4/78 Appendix C Report No. : FA480804 Page: 5/78 Appendix C Report No. : FA480804 Page: 6/78 Appendix C Report No. : FA480804 Page: 7/78 Appendix C Report No. : FA480804 Page: 8/78 Appendix C Report No. : FA480804 Page: 9/78 Appendix C Report No. : FA480804 Page: 10/78 Appendix C Report No. : FA480804 Page: 11/78 Appendix C Report No. : FA480804 Page: 12/78 Appendix C Report No. : FA480804 Page: 13/78 Appendix C Report No. : FA480804 Page: 14/78 D5GHzV2, Serial No. 1341 Extended Dipole Calibrations If dipoles are verified in return loss (<-20dB, within 20% of prior calibration), and in impedance (within 5 ohm of prior calibration), the annual calibration is not necessary and the calibration interval can be extended. 5250MHz D5GV2 – serial no. 1341 5250 Head Date of Measurement Return-Loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary Impedance (ohm) Delta (ohm) 2021.12.13 -35.7 48.4 0.1 2022.12.12 -35.7 0.0% 50.1 -1.7 -1.6 1.7 2023.12.12 -34.8 -2.5% 48.5 -0.1 -0.9 1 5600MHz D5GV2 – serial no. 1341 5600 Head Date of Measurement Return-Loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary Impedance (ohm) Delta (ohm) 2021.12.13 -22.2 53.8 7.2 2022.12.12 -22.4 0.9% 52.9 0.9 7.3 -0.1 2023.12.12 -21.3 -4.1% 52.8 1 8.3 -1.1 5750MHz D5GV2 – serial no. 1341 5750 Head Date of Measurement Return-Loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary Impedance (ohm) Delta (ohm) 2021.12.13 -25.8 51.4 5 2022.12.12 -26.1 1.2% 50.1 1.3 5 0 2023.12.12 -25.9 0.4% 51.7 -0.3 6.1 -1.1 Appendix CReport No. : FA480804 Page: 15/78 <Justification of the extended calibration> The return loss is < -20dB, within 20% of prior calibration; the impedance is within 5 ohm of prior calibration. Therefore the verification result should support extended calibration. Dipole Verification Data> D5GHzV2, serial no. 1341 5250MHz – Head----2022.12.12 5600MHz – Head----2022.12.12 Appendix CReport No. : FA480804 Page: 16/78 5750MHz – Head----2022.12.12 5250MHz – Head----2023.12.12 Appendix CReport No. : FA480804 Page: 17/78 5600MHz – Head----2023.12.12 5750MHz – Head----2023.12.12 Appendix CReport No. : FA480804 Page: 18/78 Appendix C Report No. : FA480804 Page: 19/78 Appendix C Report No. : FA480804 Page: 20/78 Appendix C Report No. : FA480804 Page: 21/78 Appendix C Report No. : FA480804 Page: 22/78 Appendix C Report No. : FA480804 Page: 23/78 Appendix C Report No. : FA480804 Page: 24/78 Appendix CReport No. : FA480804 Page: 25/78 Appendix CReport No. : FA480804 Page: 26/78 Appendix CReport No. : FA480804 Page: 27/78 Appendix CReport No. : FA480804 Page: 28/78 Appendix CReport No. : FA480804 Page: 29/78 Appendix CReport No. : FA480804 Page: 30/78 Appendix CReport No. : FA480804 Page: 31/78 Appendix CReport No. : FA480804 Page: 32/78 Appendix C Report No. : FA480804 Page: 33/78 Appendix C Report No. : FA480804 Page: 34/78 Appendix C Report No. : FA480804 Page: 35/78 Appendix C Report No. : FA480804 Page: 36/78 Appendix C Report No. : FA480804 Page: 37/78 Appendix C Report No. : FA480804 Page: 38/78 Appendix C Report No. : FA480804 Page: 39/78 Appendix C Report No. : FA480804 Page: 40/78 Appendix C Report No. : FA480804 Page: 41/78 Appendix C Report No. : FA480804 Page: 42/78

Appendix C Report No. : FA480804 Page: 43/78 Appendix C Report No. : FA480804 Page: 44/78 Appendix C Report No. : FA480804 Page: 45/78 Appendix C Report No. : FA480804 Page: 46/78 Appendix C Report No. : FA480804 Page: 47/78 Appendix C Report No. : FA480804 Page: 48/78 Appendix C Report No. : FA480804 Page: 49/78 Appendix C Report No. : FA480804 Page: 50/78 Appendix C …

Text truncated - open the document above for the full version.