2AG7VDR882Wireless Module

http://www.wallystech.com/1 DR 882 W ireless Module Wireless AC/AN MiniPCIE Standard Card Features  Featuring with industrial-grade Atheros’s QCA9882-BR4A chipset Integrated with 2x 2 5G high power Radio Card  Frequency Range: Band 1:5150~5250MHz, Band 4: 5725~5850MHz 2 x 5G MMCX Connectors  20MHz/40MHz/80MHz Bandwidth  Support 11AC/A/N RoHS compliance ensure a high level protection of human health and the environment from risks that can be posed by chemicals Applications Security Surveillance Commercial radio coverage Hotel Wireless application Country coverage Forest fire protection engineering Some special scene application Product Description DR882-NAS based on QCA9882-BR4A chipset is an enterprise wireless module integrated with 2x2 5G high power Radio card designed specifically to provide users with mobile access to high-bandwidth video streaming, voice, and data transmission for office and challenging RF environment in factories, warehouses establishment. Absolute Maximum Rating ParameterRatingUnit Supply Voltage3.3V(MINIPCIE)V Operating Temperature Range-40 to +70ºC Storage Temperature Range-65 to +105ºC Operating Humidity Range5 to +95 (non-condensing)% Storage Humidity Range0 to +90 (non-condensing)% http://www.wallystech.com/2 SymbolParameter CPU QCA9882-BR4A Antenna Connector2 x 5G MMCX connectors ROHS ComplianceYES Dimension50mm x 30mm x 16mm Radio TX Specifications(5180MHz-5825MHz) Operating Mode frequency range 802.11a 802.11ac20 802.11n-HT20 802.11ac40 802.11n-HT40 802.11ac80 5150~52500 5725~58500 5150~52500 5725~58500 5150~52500 5725~58500 5150~52500 5725~58500 5150~52500 5725~58500 5210 5775 Tune-up Output Power 17dBm 17dBm 17dBm 17d Bm 17 dBm 17dBm 16.50dBm 17d Bm 17dBm 17dBm 16.50dBm 16.50dBm GPIO Pin Mapping GPIO PinFunction GPIO0WLAN_DIS GPIO1WLAN_LED GPIO2MCI_CLK_IN GPIO3MCI_CLK_OUT GPIO4MCI_DATA_OUT GPIO5MCI_DATA_IN GPIO12TMS 13TCK 14TDI 15TDO 16CPU_WARM_RESET / JTEG RESET 17GPIO17_BT_LED 19ANT_A 20ANT_B 21FEM_BS 22FEM_MODE http://www.wallystech.com/3 Radio RX Specifications(5180MHz-5825MHz) Operating ModeData RateSensitivity 802.11a 6 Mbps-96dBm 54 Mbps-78dBm 802.11n HT20 MCS0, MCS8-92dBm MCS7, MCS15-73dBm 802.11n HT40 MCS0, MCS8-90dBm MCS7, MCS15-70dBm 802.11AC HT40 MCS0, MCS10,MCS20-90dBm MCS9,MCS19,MCS29-67dBm 802.11AC HT80 MCS0, MCS10,MCS20-88dBm MCS9,MCS19,MCS29-62dBm http://www.wallystech.com/4 MiniPCIe Slot Pin Assignment TOP SideBottom Side 1PCIE_WAKE_L2VCC_3V3 3NC4GND 5NC6NC 7PCIE_CLKREQ_L8NC 9GND10NC 11PCIE_REFCLK_N12NC 13PCIE_REFCLK_P14NC 15GND16NC Mechanical key 17NC18GND 19NC20GPIO0_WLAN_DIS 21GND22PCIE_RST_L 23PCIE_TX_N24VCC_3V3 25PCIE_TX_P26GND 27GND28NC 29GND30NC 31PCIE_RX_P32NC 33PCIE_RX_N34GND 35GND36NC 37GND38NC 39 VCC_3V3 (RESERVED) 40GND 41 VCC_3V3 (RESERVED) 42NC 43GND44GPIO1_WLAN_LED 45NC46GPIO17_BT_LED 47NC48NC 49NC50GND 51NC52VCC_3V3 http://www.wallystech.com/5 Pin1 Pin51 1 ） t he picture show us the Pin 1 and the pin51 ， t he pin numbers are increasing by odd numbers on the top side ； 2 ） a nd increasing by even numbers from Pin2 to Pin52 on the bottom side ； t he pin2 is on the bottom of the pin1 OEM/Integrators Installation: 1.0 This module has been tested and found to comply with 15.407 requirements for Limited module procedures . This module can work with 5G(Band 1,Band 4)，but the two band can't work together. 1.1. Summarize the specific operational use conditions This module can be used in Commercial radio coverage and other equipment. The input voltage to the module s hould be nominally DC 3.3V ,the ambient temperature of the module is -40°~70°.And if the antenna needs to be changed, the certification should be re-applied. 1.2. Limited module procedures This module can be used in Commercial radio coverage and other equipment. Normally host device should provide a power supply in range 3.3VDC for this module. The limit ed module manufacturer will reviews detailed test data or host designs prior to giving the host manufacturer approval. 1.3. Trace antenna designs N/A 1.4. RF exposure considerations This equipment complies with FCC radiation expos ure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. If the device built into a host as a portable usage, the additional RF exposure evaluation may be required as specified by 2.1093. 1.6. Label and compliance information When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily re-moved. If not, a second label must be placed on the outside of the final device that contains the following text: “Contains FCC ID: 2AG7VDR882”. The FCC ID can be used only when all FCC ID compliance requirements are met. 1.7. Information on test modes and additional testing requirements 1.5. Antennas Antenna 1: Omni Antenna:4.0 dBi Antenna 2&3 : Directional Antenna: 19.0 dBi a) The modular transmitter has been fully tested by the module grantee on the required number of channels,modulation types, and modes, it should not be necessary for the host installer to re-test all the available transmitter modes or settings. It is recommended that the host product manufacturer, installing the modular transmitter,perform some investigative measurements to confirm that the resulting composite system does not exceed the spurious emissions limits or band edge limits (e.g., where a different antenna may be causing additional emissions). http://www.wallystech.com/6 b) The testing should check for emissions that may occur due to the intermixing of emissions with the other transmitters, digital circuitry, or due to physical properties of the host product (enclosure). This investigation is especially important when integrating multiple modular transmitters where the certification is based on testing each of them in a stand-alone configuration. It is important to note that host product …

Text truncated - open the document above for the full version.

Date: 2020-02-17 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attestation Letter To Whom It May Concern, The chip QCA9882 installed in our product Wireless Module (model name: DR882 , FCC ID: 2AG7VDR882 ), which are supports 2.4G Wi-Fi(802.11b/802.11g/802.11n-HT20/ 802.11n- HT40) and 5G Wi-Fi(5150~5250MHz, 5250~5350MHz , 5470~5725MHz,5725~5850MHz) fuctions, But for the product, it only activates 5G Wi-Fi(5150~5250MHz, 5725~5850MHz) fuction, the 2.4G Wi-Fi(802.11b/802.11g/802.11n-HT20/ 802.11n-HT40) and5G Wi-Fi( 5250-5350MHz , 5470-5725MHz) fuctions are disabled by using the software. Please contact m e i f there i s need for a ny additional clarification or information. Best Regards, Company: Wallys Communications Technologies Co.,Ltd Add: Room 2723, Le Jia building, Jia Rui Xiang No.8, Suzhou Industrial Park, Suzhou, P.R 215000 China Tel: +86-18912606205 Fax: +86-512-62815802 E-mail: [email protected] Sincerely, Signature: Typed or Printed Name: Jason Sun Title: CEO

QA-FR-170-B Company: Wallys Communications Technologies Co.,Ltd Add: Room 2723, Le Jia building, Jia Rui Xiang No.8, Suzhou Industrial Park, Suzhou, P.R 215000 China Tel: +86-18912606205 Fax: +86-512-62815802 FCC Authorization Date: 2020-02-17 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We, Wallys Communications Technologies Co.,Ltd, the undersigned, Hereby authorizes Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratories Corp. on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature: Typed or Printed Name: Jason Sun Title: CEO

Company Name: Wallys Communications Technologies Co.,Ltd Add: Room 2723, Le Jia building, Jia Rui Xiang No.8, Suzhou Industrial Park, Suzhou, P.R 215000 China Tel: +86-18912606205 Fax: +86-512-62815802 E-mail: [email protected] FCC Confidential Authorization Date:2020-02-17 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2 AG7VDR882 To: whom it may concern, In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Wallys Communications Technologies Co.,Ltd hereby requests long-term confidential treatment of information accompanying this application as outlined below: Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Sig nature: Typed or Printed Name: Jason Sun Title: CEO

Applicant Wallys Communications Technologies Co.,Ltd FCC ID: 2AG7VDR882 Section 15.212 Modular Transmitters Request for Modular Approval  Request for Limited Modular Approval   RequirementsEUT ConditionsComply(Y/N) Single Modular Approval Requirements 1 The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. Refer to external photos. This module does not have shield cover. N 2 The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with part 15 requirements under conditions of excessive data rates or over‐modulation. All inputs to the modules are buffered through logic or microprocessor inputs. Refer to Schematics. Y 3 The modular transmitter must have its own power supply regulation. The Module uses the chip QCA9882-BR4A with built-in power management components, the module ra ted power is 3.3V power, Refer to schematics. Y 4 The modular transmitter must comply with the antenna and transmission system requirements of §§15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of §15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. The EUT has been tested with three external antennas for Wi-Fi. The antenna gain is 4dBi for Omni antenna, 19dBi for Directional antenna. Refer to external photo. Y Company: Wallys Communications Technologies Co.,Ltd Add: Room 2723, Le Jia building, Jia Rui Xiang No.8, Suzhou Industrial Park, Suzhou, P.R 215000 China Tel: +86-18912606205 Fax: +86-512-62815802 E-mail: [email protected] 5 The modular transmitter must be tested in a stand‐alone configuration, i.e., the module must not be inside another device during testing for compliance with part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in §15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see §15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see §15.31(i)). The modular transmitter is test in the host Device. Please refer to setup photo. N 6 The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number The device Uses a permanently affixed label, refer Label .when the module is installed inside another device, then the outside of the de vice into which the module is installed,this exterior label must use wording such as the following: “Contains Transmitter Module FCC ID: 2AG7VDR882 ” or “Contains FCC ID: 2AG7VDR882 ”. Y 7 The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. Refer to manual Y 8 The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. The EUT comply with RF exposure requirements § 2.1091.If the device built into a host as a portable usage, the RF exposure evaluation may be required as specified by§ 2.1093. Y Sincerely, Signature: Typed or Printed Name: Jason Sun Title: CEO

EXHIBIT A - EUT EXTERNAL PHOTOGRAPHS Host Device EUT 5G Wi-Fi Chain0 Port 5G Wi-Fi Chain1 Port Antenna 1 Antenna 2 Antenna 3

EXHIBIT B - EUT INTERNAL PHOTOGRAPHS Host Device EUT EUT

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA200217003-00A FCC Part 15.407 Page 27 of 258 Calculated Data: 5G Wi-Fi (Chain 1& Chain 2) Mode Frequency Range Antenna Gain Tune-up Conducted Power Evaluation Distance Power Density MPE Limit (MHz) (dBi) (numeric)(dBm)(mW)(cm) (mW/cm 2 ) (mW/cm 2 ) 802.11a 5150~5250 19.0 79.63 17.0050.1220 0.7919 1.0 5725~5850 19.0 79.63 17.0050.1220 0.7919 1.0 802.11ac20 5150~5250 19.0 79.63 17.0050.1220 0.7919 1.0 5725~5850 19.0 79.63 17.0050.1220 0.7919 1.0 802.11n20 5150~5250 19.0 79.63 17.0050.1220 0.7919 1.0 5725~5850 19.0 79.63 17.0050.1220 0.7919 1.0 802.11ac40 5150~5250 19.0 79.63 16.5044.6720 0.7058 1.0 5725~5850 19.0 79.63 17.0050.1220 0.7919 1.0 802.11n40 5150~5250 19.0 79.63 17.0050.1220 0.7919 1.0 5725~5850 19.0 79.63 17.0050.1220 0.7919 1.0 802.11ac80 5210 19.0 79.63 16.5044.6720 0.7058 1.0 5775 19.0 79.63 16.5044.6720 0.7058 1.0 Note: The Tune-up output power was declared by the Manufacturer. Conclusion: The EUT meets exemption requirement - RF exposure evaluation greater than 20cm distance specified in § 2.1091. If the device built into a host as a portable usage, the additional RF exposure evaluation may be required as specified by§ 2.1093.

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. FCC PART 15.407 TEST REPORT For Wallys Communications Technologies Co.,Ltd Room 2723, Le Jia building, Jia Rui Xiang No.8, Suzhou Industrial Park, Suzhou, P.R 215000 China FCC ID: 2AG7VDR882 Report Type: Original Report Product Type: Wireless Module Test En gineer: Stone Zhang Re port Number: RSHA200217003-00A Re port Date: 2020-06-23 Reviewed By: Oscar Ye EMC Manager Test Laboratory: Bay Area Compliance Laboratories Corp. (Kunshan) No.248 Chenghu Road,Kunshan,Jiangsu province,China Tel: +86-0512-86175000 Fax: +86-0512-88934268 www.baclcorp.com.cn Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA200217003-00A FCC Part 15.407 Page 2 of 258 TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 4 OBJECTIVE ................................................................................................................................................................... 4 RELATED SUBMITTAL(S)/GRANT(S) ............................................................................................................................. 4 TEST METHODOLOGY .................................................................................................................................................. 4 MEASUREMENT UNCERTAINTY .................................................................................................................................... 5 TEST FACILITY ............................................................................................................................................................. 5 SYSTEM TEST CONFIGURATION .......................................................................................................................... 6 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 6 EUT EXERCISE SOFTWARE .......................................................................................................................................... 7 EQUIPMENT MODIFICATIONS ..................................................................................................................................... 22 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................. 22 EXTERNAL I/O CABLE ................................................................................................................................................ 22 BLOCK DIAGRAM OF TEST SETUP .............................................................................................................................. 22 SUMMARY OF TEST RESULTS ............................................................................................................................. 24 TEST EQUIPMENT LIST ......................................................................................................................................... 25 §1.1310& §2.1091 - MAXIMUM PERMISSIBLE EXPOSURE (MPE) ..................................................................... 26 APPLICABLE STANDARD ............................................................................................................................................ 26 CALCULATED FORMULARY: ....................................................................................................................................... 26 FCC §15.203 – ANTENNA REQUIREMENT .......................................................................................................... 28 APPLICABLE STANDARD ............................................................................................................................................ 28 ANTENNA CONNECTOR CONSTRUCTION .................................................................................................................... 28 FCC §15.407 (b) (6) §15.207 (a) – AC POWER LINE CONDUCTED EMISSIONS ............................................ 29 APPLICABLE STANDARD ............................................................................................................................................ 29 EUT SETUP ................................................................................................................................................................ 29 EMI TEST RECEIVER SETUP ....................................................................................................................................... 29 TEST PROCEDURE ...................................................................................................................................................... 30 CORRECTED FACTOR & OVER LIMIT CALCULATION .................................................................................................. 30 TEST RESULTS SUMMARY .......................................................................................................................................... 30 TEST DATA ................................................................................................................................................................ 30 §15.205 & §15.209 & §15.407(B) (1),(4),(6),(7) – UNDESIRABLE EMISSION & RESTRICTED BANDS ....... 43 APPLICABLE STANDARD ...........................................................................................................…

Text truncated - open the document above for the full version.

Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA200217003-00A FCC Part 15.407 Page 142 of 258 Middle Channel: 5200MHz 0 20 40 60 80 100 1G2G3G4G5G6 8 10G18G Level in dB μ V/ Frequency in Hz Full Spectrum Frequency (MHz) Corrected Amplitude Rx Antenna Turntable Degree Correct Factor (dB/m) Limit (dBμV/m) Margin (dB) MaxPeak (dBμV/m) Average (dBμV/m) Height (cm) Polar (H/V) 1799.00 46.92 --- 150 H 219 -15.2 68.20 21.28 2496.00 --- 32.03 150 V 216 -12.4 54.00 21.97 2496.00 41.94 --- 150 V 216 -12.4 74.00 32.06 3465.00 47.55 --- 150 V 187 -8.9 68.20 20.65 5974.20 49.46 --- 150 V 0 -3 68.20 18.74 6933.00 48.87 --- 150 V 0 -0.2 68.20 19.33 17459.40 54.67 --- 200 V 319 8.8 68.20 13.53 Fundamental Test with notch filter Level in dB μ V/m Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA200217003-00A FCC Part 15.407 Page 143 of 258 High Channel: 5240MHz 0 20 40 60 80 100 1G2G3G4G5G6 8 10G18G Level in dB μ V/ Frequency in Hz Full Spectrum Frequency (MHz) Corrected Amplitude Rx Antenna Turntable Degree Correct Factor (dB/m) Limit (dBμV/m) Margin (dB) MaxPeak (dBμV/m) Average (dBμV/m) Height (cm) Polar (H/V) 1124.10 35.08 --- 200 H 219 -18.4 74.00 38.92 1124.10 --- 28.95 200 H 219 -18.4 54.00 25.05 1799.00 46.41 --- 150 H 233 -15.2 68.20 21.79 2497.70 --- 32.70 150 V 152 -12.4 54.00 21.30 2497.70 41.82 --- 150 V 152 -12.4 74.00 32.18 3492.20 46.92 --- 150 V 181 -8.8 68.20 21.28 5909.60 49.01 --- 150 V 358 -3.2 68.20 19.19 17457.70 55.49 --- 200 V 144 8.7 68.20 12.71 Fundamental Test with notch filter Level in dB μ V/m Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA200217003-00A FCC Part 15.407 Page 144 of 258 802.11ac20 Mode(Chain 0+Chain 1): (Pre-scan in the X, Y and Z axes of orientation, the worst case Z-axis of orientation was recorded.) Note: 1. This test was performed with the 5150-5250MHz band reject filter. 2. Corrected Factor = Antenna factor (RX) + Cable Loss – Amplifier Factor Corrected Amplitude = Corrected Factor + Reading Mar gin = Limit - Corrected. Amplitude Low Channel: 5180MHz 0 20 40 60 80 100 1G2G3G4G5G6 8 10G18G Level in dB μ V/ Frequency in Hz Full Spectrum Frequency (MHz) Corrected Amplitude Rx Antenna Turntable Degree Correct Factor (dB/m) Limit (dBμV/m) Margin (dB) MaxPeak (dBμV/m) Average (dBμV/m) Height (cm) Polar (H/V) 1453.90 --- 30.67 150 V 230 -16.6 54.00 23.33 1453.90 44.13 --- 150 V 230 -16.6 74.00 29.87 1799.00 45.86 --- 150 H 227 -15.2 68.20 22.34 2492.60 --- 29.01 150 V 156 -12.5 54.00 24.99 2492.60 42.28 --- 200 V 184 -12.5 74.00 31.72 3453.10 44.91 --- 150 V 185 -8.9 68.20 23.29 6905.80 51.08 --- 150 V 0 -0.3 68.20 17.12 17490.00 54.92 --- 150 V 13 8.9 68.20 13.28 Fundamental Test with notch filter Level in dB μ V/m Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA200217003-00A FCC Part 15.407 Page 145 of 258 Middle Channel: 5200MHz 0 20 40 60 80 100 1G2G3G4G5G6 8 10G18G Level in dB μ V/ Frequency in Hz Full Spectrum Frequency (MHz) Corrected Amplitude Rx Antenna Turntable Degree Correct Factor (dB/m) Limit (dBμV/m) Margin (dB) MaxPeak (dBμV/m) Average (dBμV/m) Height (cm) Polar (H/V) 1799.00 45.20 --- 150 H 227 -15.2 68.20 23.00 3453.10 45.82 --- 150 V 187 -8.9 68.20 22.38 5850.10 54.50 --- 150 H 353 -3.3 68.20 13.70 6905.80 50.70 --- 150 V 1 -0.3 68.20 17.50 10470.70 49.03 --- 150 V 329 2.3 68.20 19.17 17933.70 54.39 --- 200 H 153 8.8 74.00 19.61 17933.70 --- 45.67 200 H 153 8.8 54.00 8.33 Fundamental Test with notch filter Level in dB μ V/m Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA200217003-00A FCC Part 15.407 Page 146 of 258 High Channel: 5240MHz 0 20 40 60 80 100 1G2G3G4G5G6 8 10G18G Level in dB μ V/ Frequency in Hz Full Spectrum Frequency (MHz) Corrected Amplitude Rx Antenna Turntable Degree Correct Factor (dB/m) Limit (dBμV/m) Margin (dB) MaxPeak (dBμV/m) Average (dBμV/m) Height (cm) Polar (H/V) 1799.00 46.21 --- 150 H 227 -15.2 68.20 21.99 3453.10 44.62 --- 150 V 187 -8.9 68.20 23.58 5833.10 54.26 --- 150 H 0 -3.3 68.20 13.94 6905.80 49.64 --- 200 V 0 -0.3 68.20 18.56 10545.50 47.77 --- 200 H 112 2.4 68.20 20.43 17486.60 54.79 --- 150 H 212 8.8 68.20 13.41 Fundamental Test with notch filter Level in dB μ V/m Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA200217003-00A FCC Part 15.407 Page 147 of 258 802.11n-HT20 Mode(Chain 0+Chain 1): Pre-scan with X,Y and Z axes of orientation, the worst case Z-axis of orientation was recorded Note: 1. This test was performed with the 5150-5250MHz band reject filter. 2. Corrected Factor = Antenna factor (RX) + Cable Loss – Amplifier Factor Corrected Amplitude = Corrected Factor + Reading Mar gin = Limit - Corrected. Amplitude Low Channel: 5180MHz 0 20 40 60 80 100 1G2G3G4G5G6 8 10G18G Level in dB μ V/ Frequency in Hz Full Spectrum Frequency (MHz) Corrected Amplitude Rx Antenna Turntable Degree Correct Factor (dB/m) Limit (dBμV/m) Margin (dB) MaxPeak (dBμV/m) Average (dBμV/m) Height (cm) Polar (H/V) 1472.60 --- 29.69 200 V 242 -16.5 54.00 24.31 1472.60 44.94 --- 200 V 242 -16.5 74.00 29.06 1799.00 45.51 --- 150 H 227 -15.2 68.20 22.69 3453.10 45.28 --- 150 V 177 -8.9 68.20 22.92 5811.00 55.74 --- 150 H 0 -3.3 68.20 12.46 6905.80 50.47 --- 150 V 0 -0.3 68.20 17.73 17505.30 54.40 --- 200 V 333 8.9 68.20 13.80 Fundamental Test with notch filter Level in dB μ V/m Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RSHA200217003-00A FCC Part 15.407 Page 148 of 258 Middle Channel: 5200MHz 0 20 40 60 80 100 1G2G3G4G5G6 8 10G18G Level in dB μ V/ Frequency in Hz Full Spectrum Frequency (MHz) Corrected Amplitude Rx Antenna Turntable Degree Correct Factor (dB/m) Limit (dBμV/m) Margin (dB) MaxPeak (dBμV/m) Average (dBμV/m) Height (cm) Polar (H/V) 1799.00 45.19 --- 150 H 247 -15.2 68.20 23.01 2497.70 --- 32.31 200 V 188 -12.4 54.00 21.69 2497.70 40.94 --- 200 V 188 -12.4 74.00 33.06 3465.00 46.08 --- 150 V 177 -8.9 68.20 22.12 5799.10 53.94 --- 150 H 0 -3.4 68.20 14.26 6933.00 49.11 --- 150 V 0 -0.2 68.20 19.09 17632.…

Text truncated - open the document above for the full version.

EXHIBIT C - TEST SETUP PHOTOGRAPHS AC power line conducted emissions Front View AC power line conducted emissions Side View Radiated Emissions View (Below 1 GHz) Radiated Emissions View (1GHz-18GHz) Radiated Emissions View (18GHz-40GHz) AC power line conducted emissions Front View AC power line conducted emissions Side View Radiated Emissions View (Below 1 GHz) Radiated Emissions View (1GHz-18GHz) Radiated Emissions View (18GHz-40GHz) AC power line conducted emissions Front View AC power line conducted emissions Side View Radiated Emissions View (Below 1 GHz) Radiated Emissions View (1GHz-18GHz) Radiated Emissions View (18GHz-40GHz)