2AGCXLQSQ5The remote control

1 Wireless remote control operation instruction Product introduction 1.1 The appearance and buttons Figure 1. The remote control appearance As shown in figure 1, the remote control has four separate button, from left to right are respectively Followed by mode conversion button, horn button, unlock button, switch button. 1.2 Product function is introduced 2 （I）Lock unlock: if the car is locked, original click ，The car unlocked. If the car is not locked, original click，car lock. （II）Unlock: original click ，The car unlocked. If the original is not locked, also can't lock the button press a few times, it is pure unlock button. with button press can trigger the calibration function. (In the calibration status, keep the car pedal parallel to the ground. ) （III）Calibration profile: At the same time hold down the ，There will be 1 of "di ~", until the tail lights flash began to seconds. The current profile data was successfully saved, switch the power button again. （IIII）Buzzer: hold down the ，The car alarm, horn of nights. （IV）Mode switch: press ，From the two modes to switch back and forth. Electricity low sensitive mode by default. When the car balance total power, balance the car hasn't been used, automatically turn off the power supply in an hour. Total power switch is not open the remote control doesn't work. 3 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna transmitter. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to 4 radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.

External Photos

Label & Location Label Location

This test report is limited to the above client company and the product mode only. It may not be duplicated without prior written consent of Shenzhen Microtest Co., Ltd. Tel:(86-755)88850135 Fax: (86-755) 88850136 http://www.mtitest.com E-mail: [email protected] Add: 1F & 3F, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, P. R. China Test Report FCC ID.: 2AGCXLQSQ5 Date of issue: Dec. 10, 2015 Sample Description: The remote control Model(s): Q5 Applicant: Shenzhen Knight Electronics Co., Ltd. Address: 4th Building, Hongxiang Industrial Park, Hezhou Village, Xixiang Town, Baoan District, Shenzhen, Guangdong, China Date of Test: Oct. 12, 2015 to Dec. 03, 2015 Shenzhen Microtest Co., Ltd. http://www.mtitest.com - Page 2 of 15- Report No.: MTI151010004RF01 This test report is limited to the above client company and the product mode only. It may not be duplicated without prior written consent of Shenzhen Microtest Co., Ltd. Tel:(86-755)88850135 Fax: (86-755) 88850136 http://www.mtitest.com E-mail: [email protected] Add: 1F & 3F, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, P. R. China TABALE OF CONTENTS 1. General description ...................................................................................................... 5 1.1 Feature of equipment under test (EUT) ...................................................................... 5 1.2 operation channel list .................................................................................................. 5 2. Test Configuration of EUT ........................................................................................... 6 2.1 EUT operation mode .................................................................................................... 6 2.2 Test conditions ............................................................................................................. 6 2.3 Testing site ................................................................................................................... 6 2.4 Ancillary equipment list............................................................................................... 6 2.5 Measurement uncertainty ........................................................................................... 6 3. List of test equipment .................................................................................................. 7 4. Test Result .................................................................................................................... 8 4.1 Antenna requirement ................................................................................................... 8 4.2 20dB emission bandwidth ........................................................................................... 9 4.3 Radiated emission ..................................................................................................... 10 4.4 Time of occupancy (dwell time) ................................................................................ 15 - Page 3 of 15- Report No.: MTI151010004RF01 Tel:(86-755)88850135 Fax: (86-755) 88850136 http://www.mtitest.com E-mail: [email protected] Address: 1F & 3F, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, P. R. China. TEST RESULT CERTIFICATION Applicant’s name: Shenzhen Knight Electronics Co., Ltd. Address: 4th Building, Hongxiang Industrial Park, Hezhou Village, Xixiang Town, Baoan District, Shenzhen, Guangdong, China Manufacture's Name: Shenzhen Knight Electronics Co., Ltd. Address: 4th Building, Hongxiang Industrial Park, Hezhou Village, Xixiang Town, Baoan District, Shenzhen, Guangdong, China Product description Product name: The remote control Trademark: / Model name: Q5 Serial Model: / Standards: FCC Part 15.231 Test Procedure: ANSI C63.4-2009 This device described above has been tested by Shenzhen Microtest Co., Ltd. and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. Tested By : David Chen Dec. 10, 2015 Reviewed By : Leon Chen Dec. 10, 2015 Approved By : Ares Liu Dec. 10, 2015 - Page 4 of 15- Report No.: MTI151010004RF01 Tel:(86-755)88850135 Fax: (86-755) 88850136 http://www.mtitest.com E-mail: [email protected] Address: 1F & 3F, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, P. R. China. SUMMARY OF TEST RESULT Item FCC Part No. Description of Test Result 1 15.203 Antenna requirement Pass 2 15.207 AC power line conducted emission N/A 3 15.231(c) 20dB bandwidth Pass 4 15.231(b) Radiated emission Pass 5 15.231(a)(1) Release time Pass - Page 5 of 15- Report No.: MTI151010004RF01 Tel:(86-755)88850135 Fax: (86-755) 88850136 http://www.mtitest.com E-mail: [email protected] Address: 1F & 3F, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, P. R. China. 1. General description 1.1 Feature of equipment under test (EUT) Product name: The remote control Model name: Q5 Serial Model: / Tx/Rx frequency range: Tx: 315MHz Modulation type: ASK Modulation Technology: OOK Power source: 3VDC (CR2032 battery) Adapter information: / Antenna designation: PCBA antenna (Antenna Gain: 1.3dBi) Hardware version: V1.1 Software version: V1.0 1.2 operation channel list Channel Frequency 1 315MHz - Page 6 of 15- Report No.: MTI151010004RF01 Tel:(86-755)88850135 Fax: (86-755) 88850136 http://www.mtitest.com E-mail: [email protected] Address: 1F & 3F, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, P. R. China. 2. Test Configuration of EUT 2.1 EUT operation mode During testing, the EUT is operated in a normal mode. 2.2 Test conditions During the measurement the environmental conditions were within the listed ranges: - Temperature: 20ºC~30ºC - Humidity: 30%~70% - Atmosp…

Text truncated - open the document above for the full version.

Test Setup Radiated emission - blew 1GHz Radiated emission –above 1GHz