2AHAB-KTNo-battery 915 MHz kinetic RF transmitter

User Manual Product Description: 915 MHz Kinetic RF Transmitter End-point Model Number (HVIN): 50-31F036 Model Name (PMN): Kinetic Transmitter End-point FCC ID: 2AHAB-KT IC: 8725A-KT Manufacturer: Camden Door Controls Date of Issue: June 1, 2026 1. Product Overview The Kinetic Transmitter is a 915 MHz RF transmitter using energy harvesting technology. The transmitter does not require any batteries, providing a maintenance-free installation that operates on radio frequency to provide easy installation of automatic door activation switches. 2. Package Contents • 1 x Kinetic Transmitter • 1 x User Manual 3. Installation & Setup 3.1 Powering the Device The Kinetic Transmitter does not require any external power. It uses an energy harvesting magnetic coil. Physical force is used to push a magnet across a coil, which generates enough energy to power a small RF generator. 3.2 Basic Operation The Kinetic Transmitter End-point can be paired with Camden RF Receivers. Pairing is achieved by pressing the Pair button on the receiver and then activating the Kinetic Transmitter End-point. 4. Wireless Operation This product operates using Sub-GHz ISM-band radio communication. Radio operation is automatic and managed by the internal firmware. Users cannot modify transmission parameters such as power level, frequency, or modulation. 5. Regulatory Notices 5.1 FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Page 1 of 3 Kinetic Transmitter End-point Kinetic Transmitter End-point User Manual Page 2 of 3 • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. 5.2 FCC RF Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, this equipment should be installed and operated with minimum distance 20 cm (7.9 inches) between the antenna and your body during normal operation. Users must follow the specific operating instructions for satisfying RF exposure compliance. 5.3 ISED Compliance Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. This device complies with the Canadian ICES-003 Class B specifications. CAN ICES-003(B) / NMB-003 (B). L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempt de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. 5.4 ISED RF Exposure Statement This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm (7.9 inches) between the radiator and any part of your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet équipement est conforme aux limites d’exposition aux radiations ISED CNR-102 établies pour un environnement non contrôlé. Une distance de séparation d’au moins 20 cm doivent être maintenue entre l’antenne de cet appareil et toutes les personnes. Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec d’autres. Kindetic Transmitter End-point User Manual Page 3 of 3 Call: 1.877.226.3369 / 905.366.3377 Visit: www.camdencontrols.com Opening New Doors to Innovation, Quality and Support! File: Kinetic Transmitter End-point Manual.indd Revision: June 1, 2026 Part No.: 40-82B392 6. Certfication and Approvals • FCC ID: 2AHAB-KT • IC: 8725A-KT • Complies with applicable FCC Part 15 and ISED RSS standards 7. Safety and Maintenance • Do not disassemble or modify the product. • Do not expose the device to water, fire, or excessive heat.…

Text truncated - open the document above for the full version.

2395 Skymark Avenue Telephone: 1 (905) 366-3377 Mississauga, ON Canada L4W 4Y6 Toll Free: 1 (877) 226-3369 www.camdencontrols.com Dated: July 13, 2026 Nemko North America, Inc. 303 River Road Ottawa ON K1V 1H2 Canada Covered Equipment Certification Attestation Letter Applicant: Camden Door Controls FCC ID: 2AHAB-KT The applicant certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section §2.903 of the FCC rules. This includes certifying that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current FCC Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. The applicant certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Signature: Name: Jack Lewis Title: Engineering Manager Company: Camden Door Controls Address: 2395 Skymark Avenue, Mississauga, Ontario, L4W 4Y6 Canada Phone: 905 366-3377 ext. 231 Email: [email protected]

2395 Skymark Avenue Telephone: 1 (905) 366-3377 Mississauga, ON Canada L4W 4Y6 Toll Free: 1 (877) 226-3369 www.camdencontrols.com Dated: July 13, 2026 Nemko North America, Inc. 303 River Road Ottawa ON K1V 1H2 Canada U.S. Agent Designation for Service of Process Attestation Letter FCC ID: 2AHAB-KT Applicant FRN: 0025205055 This letter serves as a formal designation, pursuant to §2.911(d)(7) of the FCC Rules, of the following U.S. Agent for Service of Process for the equipment under application: U.S. Agent for Service of Process: • Company Name: Camden Door Controls Inc. • Physical U.S. Company Address: 682 Mahogany run, Palm Coast, FL 32137 USA • Agent Name*: Gary Martin • Agent Email Address: [email protected] • Agent FRN**: 0037338084 The above listed designated agent hereby acknowledges and accepts the obligation for service of process on behalf of the applicant signed below. The applicant further acknowledges and accepts its obligation to maintain a U.S. Agent for Service of Process for a minimum period of one year following either: • Permanent termination of all marketing and importation activities within the U.S. for the applicable equipment by the grantee. • The conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever occurs later. Applicant Signed: Designated Agent Signed: (Required, if different to Applicant) Signed: Signed: Printed name: Jack Lewis Printed name: Gary Martin Title: Engineering Manager Title: Product Manager Company Name: Camden Door Controls Company Name: Camden Door Controls Inc. Phone: (905) 366-3377 x231 Phone: (407) 683-5406 Email: [email protected] Email: [email protected]

2395 Skymark Avenue Telephone: 1 (905) 366-3377 Mississauga, ON Canada L4W 4Y6 Toll Free: 1 (877) 226-3369 www.camdencontrols.com Dated: July 13, 2026 Nemko North America, Inc. 303 River Road, Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Appointment of Agent for FCC Certification Application Dear Director of Certification, This letter formally appoints Spencer Zhong of Nemko Canada, Inc. located at 303 River Road, Ottawa, Ontario, Canada K1V 1H2, as our authorized agent to represent us in the application process for equipment certification. We confirm that the submitted documents accurately depict the device or system seeking certification. Additionally, we guarantee that all units produced, imported, or marketed, as defined by FCC regulations, will possess a label identical to the one submitted with this application. By signing below, we certify that neither our company nor any party involved in the application is subject to denial of federal benefits, including FCC benefits, as outlined in Section 5301 of the Anti-Drug Abuse Act of 1988 (21 U.S.C. §862) due to a conviction for possession or distribution of a controlled substance. Furthermore, no party involved in the application, as defined in 47 CFR 1.2002 (b), is subject to denial of federal benefits, including FCC benefits. We attest to the truth and accuracy of the information provided to the FCC to the best of our knowledge (47 CFR 2.911 (d)) and acknowledge our responsibilities as a grantee regarding certified equipment (47 CFR 2.909). In instances where our authorized agent signs the application for certification on our behalf, we understand that Nemko North America, Inc. remains solely responsible for adhering to the terms and conditions for certification as specified by Nemko Canada Inc. Agency agreement expiration date: July 1, 2027 *Up to 12 months Sincerely, Signature: Name: Jack Lewis Title: Engineering Manager Company: Camden Door Controls Address: 2395 Skymark Avenue, Mississauga, Ontario, L4W 4Y6 Canada Phone: 905 366-3377 ext. 231 Email: [email protected]

2395 Skymark Avenue Telephone: 1 (905) 366-3377 Mississauga, ON Canada L4W 4Y6 Toll Free: 1 (877) 226-3369 www.camdencontrols.com Dated: August 10, 2026 Nemko North America, Inc. 303 River Road, Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Confidentiality Request Letter – FCC FCC ID: 2AHAB-KT Pursuant to FCC 47 CFR 0.457(d)(1)(ii) and 0.459 and FCC guidance published in KDB 726920, we hereby request confidential treatment of information accompanying this application as outlined below. Long Term Confidentiality (LTC) request We request the exhibits selected below as long term confidential be withheld from public view permanently: Selection Exhibit name ☒ Block Diagrams ☒ Operation Description / Theory of Operation ☒ Parts List & Placement / BOM ☒ Schematics Short Term Confidentiality (STC) request We also request the exhibits selected below as short term confidential be withheld from public view for a period of 45 days 1 from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public: Selection 2 Exhibit name ☒ User’s Manual ☒ Internal Photos Justification for Confidentiality The development of this product represents a significant investment and a strategic competitive differentiator for our company. Unrestricted public access to its design specifics would negate this hard-earned advantage, leading to considerable financial hardship. In the event of market introduction before the designated short-term confidentiality period expires, the grantee will notify the TCB to ensure timely release of the confidential information on the FCC equipment authorization website. The content herein contains trade secrets and proprietary information not typically released to the public. Disclosure of this information could severely impact the applicant and provide an unfair advantage to competitors. The Applicant acknowledges that, under Rule 0.457(d)(1)(ii), this Application and all associated materials will not be disclosed before the Grant date. 1 - Number of days can be listed up to 180 but should not go past the date of beginning of product marketing/sale. 2 - Any exhibits that may have already been requested to have “Permanent” confidentiality need not be repeated under Short-Term confidentiality request. 2395 Skymark Avenue Telephone: 1 (905) 366-3377 Mississauga, ON Canada L4W 4Y6 Toll Free: 1 (877) 226-3369 www.camdencontrols.com Sincerely, Signature: Name: Jack Lewis Title: Engineering Manager Company: Camden Door Controls Address: 2395 Skymark Avenue, Mississauga, Ontario, L4W 4Y6 Canada Phone: 905 366-3377 ext. 231 Email: [email protected]

External Photographs Exhibit Model Number: 50-31F036 FCC ID: 2AHAB-KT IC: 8725A-KT Applicant: Camden Door Controls Date: August 11, 2026 Purpose This exhibit provides clear and detailed external photographs of the subject device as required under FCC §2.1033(b)(7) and ISED RSS-GEN Section 3.2(e). Notes • All photos are representative of the production unit. • No photos have been digitally altered except for cropping or brightness adjustments to improve visibility. • Confidentiality has been requested for these internal photos per FCC §0.459 / ISED RSP-100 Section 10. 1. Overview of Main PCB (Component Side) Figure 1. PCB top side(a). Figure 2. PCB top side(b). 2. Overview of Main PCB (Solder Side) Figure 3. PSB bottom side. 3. Close-up of RF Section Figure 4. RF circuitry. 4. Antenna(s) Figure 5. Wire Antenna. 5. Overall Device Assembly Figure 6. PCBA side view. Figure 7. PCBA front view. Figure 8. PCBA back side view. Figure 9. PCBA bottom side view.

Label design: Label location:

www.nemko.com Nemko Canada Inc., a testing laboratory, is accredited by ANSI National Accreditation Board (ANAB). The tests included in this report are within the scope of this accreditation. The ANAB symbol is an official symbol of the ANSI National Accreditation Board, used under licence. ANAB File Number: AT-3195 (Ottawa); AT-3193 (Pointe-Claire); AT-3194 (Cambridge) FCC and RSS-102 Annex C – MPE Calculation; Date: August 2023 C h o o s e S c a n d i n a v i a n t r u s t RADIO TEST REPORT Report ID Project ID REP141527 PRJ0092733 Type of assessment: MPE Calculation report Manufacturer: Hardware Version Identification Number (HVIN): Camden Door Controls 50-31F036 Product Marketing Name (PMN): Kinetic Transmitter End-point FCC identifier: ISED certification number: FCC ID: 2AHAB-KT IC: 8725A-KT Specification:  FCC 47 CFR Part 1 Subpart I, §§1.1307, 1.1310  FCC 47 CFR Part 2 Subpart J, §2.1091  FCC KDB 447498 D01 General RF Exposure Guidance v06  ISED Canada RSS-102 Issue 6, (December 2023) RSS-102 Annex B - Declaration of RF Exposure Compliance ATTESTATION: I attest that the information provided in Annex A is correct; that the Technical Brief was prepared and the information contained therein is correct; that the device evaluation was performed or supervised by me; that applicable measurement methods and evaluation methodologies have been followed; and that the device meets the SAR and/or RF field strength limits of RSS-102. Date of issue: August 14, 2026 Tarek Elkholy, EMC/RF Engineer Prepared by Signature Section 1 MPE calculation Report reference ID: REP141527 Page 2 of 4 Lab locations Company name Nemko Canada Inc. Facilities Ottawa site: 303 River Road, Ottawa, ON, Canada, K1V 1H2 Tel: +1 613 737 9680 Test site registration number: CA2040 Montréal site: 292 Labrosse Avenue, Pointe-Claire, QC, Canada, H9R 5L8 Tel: +1 514 694 2684 Test site registration number: CA2041 Cambridge site: 1-130 Saltsman Drive, Cambridge, ON, Canada, N3E 0B2 Tel: +1 519 650 4811 Test site registration number: CA0101 Website www.nemko.com Limits of responsibility Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. All results contained in this report are within Nemko Canada’s ISO/IEC 17025 accreditation. Copyright notification Nemko Canada Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko Canada Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. © Nemko Canada Inc. Section 1 MPE calculation Report reference ID: REP141527 Page 3 of 4 Evaluation summary 1.1 MPE calculation for standalone transmission 1.1.1 References, definitions and limits FCC §2.1091(d) (2) (2) For operations within the frequency range of 300 kHz and 6 GHz (inclusive), the limits for maximum permissible exposure (MPE), derived from whole-body SAR limits and listed in Table 1 in paragraph (e)(1) of this section, may be used instead of whole-body SAR limits as set forth in paragraphs (a) through (c) of this section to evaluate the environmental impact of human exposure to RF radiation as specified in §1.1307(b) of this part, except for portable devices as defined in §2.1093 of this chapter as these evaluations shall be performed according to the SAR provisions in §2.1093. Table 1.1-1: Table 1 to §1.1310(e)(1) — Limits for Maximum Permissible Exposure (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (i) Limits for Occupational/Controlled Exposure 0.3–3.0 614 1.63 *(100) ≤6 3.0–30 1842 / f 4.89 / f *(900 / f 2 ) <6 30–300 61.4 0.163 1.0 <6 300–1500 f / 300 <6 1500–100000 5 <6 (ii) Limits for General Population/Uncontrolled Exposure 0.3–1.34 614 1.63 *(100) <30 1.34–30 824 / f 2.19 / f *(180 / f 2 ) <30 30–300 27.5 0.073 0.2 <30 300–1500 f / 1500 <30 1500–100000 1.0 <30 Notes: f = frequency in MHz. * = Plane-wave equivalent power density. RSS-102, Section 5 For the purpose of this standard, ISED has adopted the SAR and RF field strength limits established in Health Canada’s RF exposure guideline, Safety Code 6: Table 1.1-2: Table 4 to RSS-102 — RF Field Strength Limits Frequency range (MHz) Electric field strength (V/m rms) Magnetic field strength (A/m rms) Power density (W/m 2 ) Reference Period (minutes) Limits for Controlled Environment 10–20 61.4 0.163 10 6 20–48 129.8 / ƒ 0.25 0.3444 / ƒ 0.25 44.72 / ƒ 0.5 6 48–100 49.33 0.1309 6.455 6 100–6000 15.60 ƒ 0.25 0.04138 ƒ 0.25 0.6455 ƒ 0.5 6 6000–15000 137 0.364 50 6 Limits for Uncontrolled Environment 10–20 27.46 0.0728 2 6 20–48 58.07 / ƒ 0.25 0.1540 / ƒ 0.25 8.944 / ƒ 0.5 6 48–300 22.06 0.05852 1.291 6 300–6000 3.142 ƒ 0.3417 0.008335 ƒ 0.3417 0.02619 ƒ 0.6834 6 6000–15000 61.4 0.163 10 6 Notes: ƒ = frequency in MHz Section 1 MPE calculation Report reference ID: REP141527 Page 4 of 4 References, definitions and limits, continued Equation from page 18 of OET Bulletin 65, Edition 97-01 푆= 푃퐺 4휋푅 2 where: S = power density (mW/cm 2 or W/m 2 ) P = power input to the antenna (mW or W) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (cm or m) 1.1.2 EUT technical information Prediction frequency 915.22 MHz Antenna type Wire antenna Number of antennas 1 Maximum transmitter field strength 72.2 dBμV/m Duty cycle 100% Prediction distance (declared) 20 cm 1.1.3 MPE calculation for FCC Frequency, MHz Field Strength (measured), dBμV/m@3m Duty cycle, % …

Text truncated - open the document above for the full version.

www.nemko.com Nemko Canada Inc., a testing laboratory, is accredited by ANSI National Accreditation Board (ANAB). The tests included in this report are within the scope of this accreditation. The ANAB symbol is an official symbol of the ANSI National Accreditation Board, used under licence. ANAB File Number: AT-3195 (Ottawa/Almonte); AT-3193 (Pointe-Claire); AT-3194 (Cambridge) FCC 47 CFR Part 15 Subpart C, §15.249,RSS-210 Issue 9, August 2016, Annex B.10; Date: October 21, 2025 Choose Scandinavian trust RADIO TEST REPORT Report ID: REP141525 Type of assessment: Final product testing Applicant: Camden Door Controls Model(s)/HVIN(s): 50-31F036 FCC identifier: FCC ID: 2AHAB-KT Specifications:  FCC 47 CFR Part 15 Subpart C, §15.249  RSS-210, Issue 11, June 2024, Annex B.10 Date of issue: August 12, 2026 Project number: PRJ0092733 Description of product: Kinetic RF Transmitter Product marketing name (PMN): Kinetic Transmitter End‐point ISED certification number: IC: 8725A-KT Tarek Elkholy, EMC/RF Engineer Tested by Signature Atefeh Beiginezhad, EMC/RF Specialist Reviewed by Signature Report reference ID: REP141525 Page 2 of 23 Lab locations Company name Nemko Canada Inc. Facilities Ottawa site: 303 River Road, Ottawa, ON, Canada, K1V 1H2 Tel: +1 613 737 9680 Test site registration number: CA2040 Montréal site: 292 Labrosse Avenue, Pointe-Claire, QC, Canada, H9R 5L8 Tel: +1 514 694 2684 Test site registration number: CA2041 Cambridge site: 1-130 Saltsman Drive, Cambridge, ON, Canada, N3E 0B2 Tel: +1 519 650 4811 Test site registration number: CA0101 Website www.nemko.com Limits of responsibility Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. All results contained in this report are within Nemko Canada’s ISO/IEC 17025 accreditation. Copyright notification Nemko Canada Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko Canada Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. © Nemko Canada Inc. Report reference ID: REP141525 Page 3 of 23 Table of Contents Table of Contents ......................................................................................................................................................................................................... 3 Report summary ................................................................................................................................................................................. 4 1.1 Test specifications .................................................................................................................................................................................................... 4 1.2 Test methods ............................................................................................................................................................................................................ 4 1.3 Exclusions ................................................................................................................................................................................................................. 4 1.4 Statement of compliance .......................................................................................................................................................................................... 4 1.5 Test report revision history ....................................................................................................................................................................................... 4 Engineering considerations ................................................................................................................................................................. 5 2.1 Modifications incorporated in the EUT for compliance ............................................................................................................................................ 5 2.2 Technical judgment .................................................................................................................................................................................................. 5 2.3 Model variant declaration ........................................................................................................................................................................................ 5 2.4 Deviations from laboratory tests procedures ........................................................................................................................................................... 5 Test conditions ................................................................................................................................................................................... 6 3.1 Atmospheric conditions ............................................................................................................................................................................................ 6 3.2 Power supply range .................................................................................................................................................................................................. 6 Information provided by the applicant ................................................................................................................................................ 7 4.1 Disclaimer ......................................…

Text truncated - open the document above for the full version.

Model (HVIN): 50-31F036 Page 1 of 4 FCC ID: 2AHAB-KT IC: 8725A-KT Section 1. Radiated emissions setup photos 1.1 Front view C h o o s e S c a n d i n a v i a n t r u s t Setup photos – PRJ0092733 Model (HVIN): 50-31F036 Page 2 of 4 FCC ID: 2AHAB-KT IC: 8725A-KT Model (HVIN): 50-31F036 Page 3 of 4 FCC ID: 2AHAB-KT IC: 8725A-KT 1.2 Rear view Model (HVIN): 50-31F036 Page 4 of 4 FCC ID: 2AHAB-KT IC: 8725A-KT END OF REPORT