2AHCZ-LVLMATEPROLevelMatePRO

User Manual Patent Pending Hickory, NC 28601 Thank you for purchasing a LevelMatePRO wireless vehicle leveling system. This product was designed for ease of use and utilizes the best possible components and engineering to achieve accuracy you can count on. I believe you will find it to be an extremely useful and time saving tool. LevelMatePRO is proudly Made in the USA. Important Information about your LevelMatePRO The LevelMatePRO has an on/off switch which controls power from the battery to the system. When the switch is in the off position the battery is completely disconnected from the system and no power will be drawn from the battery. Turning the unit completely off using the switch is recommended when driving for long distances or when the vehicle is in storage. When the switch is in the on position the LevelMatePRO will operate in an automatic power management mode. When you first switch the unit on it will be connectable from the smartphone or tablet app and will remain that way for a configurable number of hours while the unit is not detecting motion (see Step 16 in the Setup and Installation section). After the configured number of hours with no motion detected the LevelMatePRO will enter a sleep mode to conserve the battery. Once motion is detected, the unit will wake and will be connectable again. So, when you move the vehicle and arrive at a new location you will be able to start the app and use the product to level the vehicle. If you ever try to connect to the LevelMatePRO and are unable to do so, the unit is likely in the sleep mode. You can wake the unit without motion by cycling the on/off switch to the off and then to the on position. When you move the switch to the on position you will hear 2 beeps. This will indicate that the unit is powered on and that the battery is in good condition. If you ever move the switch from the off position to the on position and don’t hear 2 beeps this will indicate that the battery needs to be replaced. Limited Warranty The warranty obligations of LogicBlue Technology (“LogicBlue”) for this product are limited to the terms set forth below. What is Covered This limited warranty covers defects in the materials and workmanship in this product. What is not Covered This limited warranty does not cover any damage, deterioration or malfunction resulting from any alteration, modification, improper or unreasonable use or maintenance, misuse, abuse, accident, neglect, exposure to excess moisture, fire, lightning, power surges, or other acts of nature. This limited warranty does not cover any damage, deterioration or malfunction resulting from the installation or removal of this product from any installation, any unauthorized tampering with this product, any repairs attempted by anyone unauthorized by LogicBlue to make such repairs, or any other cause which does not relate directly to a defect in materials and/or workmanship of this product. Without limiting any other exclusion herein, LogicBlue does not warrant that the product covered hereby, including, without limitation, the technology and/or integrated circuit(s) included in the product, will not become obsolete or that such items are or will remain compatible with any other product or technology with which the product may be used. How Long this Coverage Lasts The limited warranty for LogicBlue products is 1 year from the original date of purchase. Proof of purchase from the customer will be required for all warranty claims. Who is Covered Only the original purchaser of this product is covered under this limited warranty. This limited warranty is not transferable to subsequent purchasers or owners of this product. What LogicBlue Will Do LogicBlue will, at its sole option, will repair or replace and product determined to be defective with regard to materials or workmanship. FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the LevelMatePRO unit. • Increase the separation between the equipment and receiver. • Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 5mm between the radiator & your body. As with all electronic devices, they are susceptible to damage by static electricity discharge. Before removing the cover of this product be sure to discharge the static electricity in your body by touching a piece of grounded metal. IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause und…

Text truncated - open the document above for the full version.

C5266091_X8_Ed.1 1/1 Letter of Authorization Command Electronics, LLC Company: Command Electronics, LLC Address: 1230 19th Street Lane NW, Hickory, NC 28601 USA Product Name: LevelMatePRO Model Number: LevelMatePRO FCC Identifier: 2AHCZ-LVLMATEPRO We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Mark Ehrnsberger Date: March 2, 2020 Title: Manager Signature of applicant:

C5266091_X10_Ed.1 1/1 Command Electronics, LLC Date: March 2, 2020 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2AHCZ-LVLMATEPRO To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality ID Label/Location No No Attestation Statement No No External Photos No Block Diagram Schematics Test Report No No Test Setup Photos No User’s Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) No No SDR Software / Security Info No A bove mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: N ame: Mark Ehrnsberger Title: Manager

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLMATEPRO IC ID: 21137-LVLMATEPRO 1. EXTERIOR PHOTOGRAPHS Fig. 1 Fig. 2 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLMATEPRO IC ID: 21137-LVLMATEPRO Fig. 3 Fig. 4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLMATEPRO IC ID: 21137-LVLMATEPRO Fig. 5 Fig. 6

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD Label and Location This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1 Label location

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLMATEPRO IC ID: 21137-LVLMATEPRO 1. INTERIOR PHOTOGRAPHS Fig. 1 Fig. 2 Antenna SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLMATEPRO IC ID: 21137-LVLMATEPRO Fig. 3 Fig. 4 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLMATEPRO IC ID: 21137-LVLMATEPRO Fig. 5

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLMATEPRO ________________________________________________________________________ ___ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 3 FCC RF Exposure Evaluation 1. Product Information FCC ID : 2AHCZ-LVLMATEPRO Product name : LevelMatePRO Test Model : LevelMatePRO Power supply : Input：DC 3V（Supplied by a button battery） Bluetooth : 2402-2480MHz Channel Number : 40 channels for Bluetooth V4.1(DTS) Channel Spacing : 2MHz for Bluetooth V4.1(DTS) Modulation Type : GFSK for Bluetooth V4.1(DTS) Bluetooth Version : V4.1 Antenna Type : Internal Antenna Antenna Gain : 0dBi (maximum) Hardware version : I Software version : 3 Exposure category : General population/uncontrolled environment EUT Type : Production Unit Device Type : Portable Device 2. Evaluation method and Limit According to KDB447498 D01 General RF Exposure Guidance v06 Section 4.3.1 Standalone SAR test exclusion considerations: “Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition, listed below, is satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions.22 The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander (see 5) of section 4.1). To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, typically in the SAR measurement or SAR analysis report, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting is required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for the SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops & tablets etc.“ [(max. power of channel, including tune-up tolerance, mW)/ (min. test separation distance, mm)+ · *√f (GHz)+ ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where: • f (GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to f) in section 4.1 is applied to determine SAR test exclusion. SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLMATEPRO ________________________________________________________________________ ___ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 2 of 3 When one of the following test exclusion conditions is satisfied for all combinations of simultaneous transmission configurations, further equipment approval is not required to incorporate transmitter modules in host devices that operate in the mixed mobile and portable host platform exposure conditions. The grantee is responsible for documenting this according to Class I permissive change requirements. Antennas that qualify for standalone SAR test exclusion must apply the estimated standalone SAR to determine simultaneous transmission test exclusion. a) The [∑ of (the highest measured or estimated SAR for each standalone antenna configuration, adjusted for maximum tune-up tolerance) / 1.6 W/kg] + [∑ of MPE ratios] is ≤ 1.0. b)The SAR to peak location separation ratios of all simultaneously transmitting antenna pairs operating in portable device exposure conditions are all ≤ 0.04, and the [∑ of MPE ratios] is ≤ 1.0. 3. Refer Evaluation Method ANSI C95.1–1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. FCC KDB publication 447498 D01 General RF Exposure Guidance v06: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies. FCC CFR 47 part1 1.1310: Radiofrequency radiation exposure limits. FCC CFR 47 part2 2.1093: Radiofrequency radiation exposure evaluation: portable devices 4. Conducted Power Results <BT LE> Mode Channel Frequency (MHz) Peak Conducted Output Power (dBm) GFSK 0 2402 -0.055 19 2440 -2.016 39 2480 -0.755 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLMATEPRO ________________________________________________________________________ ___ This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 3 of 3 5. Manufacturing Tolerance <BT LE> GFSK (Peak) Channel Channel 0 Channel 19 Channel 39 Target (dBm) 0 -2 0 Tolerance ±(dB) 1.0 1.0 1.0 6. Evaluation Results 6.1 Standalone Evaluation Band/Mode f (GHz) Antenna Distance (mm) RF output power SAR Test Exclusion Threshold SAR Test Exclusion dBm mW BT LE GFSK 2.480 5 1 1.26 0.6 < 3.0 Yes Remark: 1. Output…

Text truncated - open the document above for the full version.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLMATEPRO Report No.: LCS191218115AEA This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 29 FCC TEST REPORT For Command Electronics, LLC LevelMatePRO Test Model: LevelMatePRO Prepared for : Command Electronics, LLC Address : 1230 19th Street Lane NW, Hickory, NC 28601 USA Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd. Address : 1/F., Xingyuan Industrial Park, Tongda Road, Bao’an Avenue, Bao’an District, Shenzhen, Guangdong, China Tel : (+86)755-82591330 Fax : (+86)755-82591332 Web : www.LCS-cert.com Mail : [email protected] Date of receipt of test sample : December 20, 2019 Number of tested samples : 1 Serial number : Prototype Date of Test : December 20, 2019 ~ December 26, 2019 Date of Report : January 03, 2020 SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLMATEPRO Report No.: LCS191218115AEA This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 2 of 29 FCC TEST REPORT FCC CFR 47 PART 15 C (15.247) Report Reference No. ................. : LCS191218115AEA Date of Issue ................................... : January 03, 2020 Testing Laboratory Name ............ : Shenzhen LCS Compliance Testing Laboratory Ltd. Address ........................................... : 1/F., Xingyuan Industrial Park, Tongda Road, Bao’an Avenue, Bao’an District, Shenzhen, Guangdong, China Testing Location/ Procedure ........... : Full application of Harmonised standards ■ Partial application of Harmonised standards □ Other standard testing method □ Applicant’s Name .......................... : Command Electronics, LLC Address ........................................... : 1230 19th Street Lane NW, Hickory, NC 28601 USA Test Specification Standard.......................................... : FCC CFR 47 PART 15 C (15.247) Test Report Form No. ................... : LCSEMC-1.0 TRF Originator ................................ : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF ..................................... : Dated 2011-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. EUT Description. ........................... : LevelMatePRO Trade Mark .......................................................................................................................................... : Command Electronics Model/ Type reference ........................................................................................................................ : LevelMatePRO Ratings ................................................................................................................................................ : Input：DC 3V（Supplied by a button battery） Result ........................................... : Positive Compiled by: Supervised by: Approved by: Ray Yang/ File administrators Jin Wang/ Technique principal Gavin Liang/ Manager SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLMATEPRO Report No.: LCS191218115AEA This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 3 of 29 FCC -- TEST REPORT Type / Model........................... : LevelMatePRO EUT......................................... : LevelMatePRO Applicant............................... : Command Electronics, LLC Address.................................. : 1230 19th Street Lane NW, Hickory, NC 28601 USA Telephone............................... : / Fax.......................................... : / Manufacturer........................ : Command Electronics, LLC Address................................... : 1230 19th Street Lane NW, Hickory, NC 28601 USA Telephone............................... : / Fax.......................................... : / Factory................................... : / Address................................... : / Telephone............................... : / Fax.......................................... : / Test Result Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Test Report No. : LCS191218115AEA January 03, 2020 Date of issue SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLMATEPRO Report No.: LCS191218115AEA This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 4 of 29 Revision History Revision Issue Date Revisions Revised By 000 January 03, 2020 Initial Issue Gavin Liang SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLMATEPRO Report No.: LCS191218115AEA This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 5 of 29 TABLE OF CONTENTS 1. GENERAL INFORMATION ................................................................................................................................... 6 1.1. DESCRIPTION OF DEVICE (EUT) ........................................................................................................................ 6 1.2. HOST SYSTEM CONFIGURATION LIST AND DETAILS .......................................................................................... 6 1.3. EXTERNAL I/O CABLE ...........................................................................................…

Text truncated - open the document above for the full version.

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLMATEPRO IC ID: 21137-LVLMATEPRO Page 1 of 16 Appendix A RF Test Data for BT V4.1(BT LE) (Conducted Measurement) Product Name: LevelMatePRO Trade Mark: Command Electronics Test Model: LevelMatePRO Environmental Conditions Temperature: 24.5  C Relative Humidity: 52.9% ATM Pressure: 100.0 kPa Test Engineer: Qu Xin Supervised by: Wang Chuang A.1 Duty Cycle Test Mode Test Channel Ant Duty Cycle[%] Verdict BT LE 2440 Ant1 100 PASS #im grbble1hchnnav SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLVMATEPRO IC ID: 21137-LVLMATEPRO Page 2 of 16 A.2 Maximum Conducted Peak Output Power Mode Channel Conduct Peak Power[dBm] Limit [dBm] Verdict BT LE LCH -0.055 30 PASS BT LE MCH -2.016 30 PASS BT LE HCH -0.755 30 PASS Test Graphs LCH MCH SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLVMATEPRO IC ID: 21137-LVLMATEPRO Page 3 of 16 HCH SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLVMATEPRO IC ID: 21137-LVLMATEPRO Page 4 of 16 A.3 Maximum Power Spectral Density Mode Channel PSD [dBm/3KHz] Limit [dBm/3KHz] Verdict BT LE LCH -15.044 8 PASS BT LE MCH -17.575 8 PASS BT LE HCH -16.025 8 PASS Test Graphs LCH MCH SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLVMATEPRO IC ID: 21137-LVLMATEPRO Page 5 of 16 HCH SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLVMATEPRO IC ID: 21137-LVLMATEPRO Page 6 of 16 A.4 6dB Bandwidth Mode Channel 6dB Bandwidth [MHz] Limit [MHz] Verdict BT LE LCH 0.6901 ≥0.5 PASS BT LE MCH 0.6991 ≥0.5 PASS BT LE HCH 0.7033 ≥0.5 PASS Test Graphs LCH MCH SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLVMATEPRO IC ID: 21137-LVLMATEPRO Page 7 of 16 HCH SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLVMATEPRO IC ID: 21137-LVLMATEPRO Page 8 of 16 A.5 Occupied Bandwidth Mode Channel Occupied Bandwidth [MHz] Limit [MHz] Verdict BT LE LCH 1.0399 ≥0.5 PASS BT LE MCH 1.0425 ≥0.5 PASS BT LE HCH 1.0400 ≥0.5 PASS Test Graphs LCH MCH SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLVMATEPRO IC ID: 21137-LVLMATEPRO Page 9 of 16 HCH A.6 RF Conducted Spurious Emissions Mode Channel Pref [dBm] Max. Level [dBm] Limit [dBm] Verdict BT LE LCH -0.861 -36.591 -20.861 PASS BT LE MCH -2.827 -36.525 -22.827 PASS BT LE HCH -1.567 -36.907 -21.567 PASS BT LE_LCH_Graphs Pref/BT LE/LCH SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLVMATEPRO IC ID: 21137-LVLMATEPRO Page 10 of 16 Puw/BT LE/LCH SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLVMATEPRO IC ID: 21137-LVLMATEPRO Page 11 of 16 BT LE_MCH_Graphs Pref/BT LE/MCH Puw/BT LE/MCH SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLVMATEPRO IC ID: 21137-LVLMATEPRO Page 12 of 16 BT LE_HCH_Graphs Pref/BT LE/HCH Puw/BT LE/HCH SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLVMATEPRO IC ID: 21137-LVLMATEPRO Page 13 of 16 A.7 Band-edge for RF Conducted Emissions Mode Channel Carrier Power[dBm] Max.Spurious Level [dBm] Limit [dBm] Verdict BT LE LCH -0.908 -49.249 -20.91 PASS BT LE HCH -1.299 -48.700 -21.3 PASS Test Graphs LCH HCH SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLVMATEPRO IC ID: 21137-LVLMATEPRO Page 14 of 16 A.8 Restrict-band band-edge measurements Test Mode Test Chann el Ant Freq. Power [dBm] Gain Ground Factor E [dBuV/m] Detector Limit [dBuV/ m] Verdi ct BT LE 2402 Ant1 2310.0 -42.85 2.0 0 54.40 PEAK 74 PASS Ant1 2310.0 -53.29 2.0 0 43.97 AV 54 PASS Ant1 2390.0 -41.22 2.0 0 56.04 PEAK 74 PASS Ant1 2390.0 -52.95 2.0 0 44.30 AV 54 PASS 2480 Ant1 2483.5 -42.09 2.0 0 55.16 PEAK 74 PASS Ant1 2483.5 -52.52 2.0 0 44.74 AV 54 PASS Ant1 2500.0 -41.72 2.0 0 55.54 PEAK 74 PASS Ant1 2500.0 -52.37 2.0 0 44.89 AV 54 PASS SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLVMATEPRO IC ID: 21137-LVLMATEPRO Page 15 of 16 Restrict-band band-edge measurements_BT LE_2402_Ant1_PEAK Restrict-band band-edge measurements_BT LE_2402_Ant1_AV SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLVMATEPRO IC ID: 21137-LVLMATEPRO Page 16 of 16 Restrict-band band-edge measurements_BT LE_2480_Ant1_PEAK Restrict-band band-edge measurements_BT LE_2480_Ant1_AV

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AHCZ-LVLMATEPRO IC ID: 21137-LVLMATEPRO _______________________________________________________________________________________________ 1. TEST SETUP PHOTOGRAPHS 1.1. Photo of Radiated Emissions Measurement Fig. 1 Fig. 2