2AHJLQ81Walkie Talkie

Install the batteries Change the front panel Operating the unit 1. Turning unit on/off: After inserting the battery, press and hold the MENU button for 1 second to turn on the unit, first displays the character of “8 “for one second, then displays the current channel. Press and hold the MENU button for 1 second, the unit will be turned off, and the LED screen will turn off. 2. Transmitting (sending speech) a. Press and hold the PTT (Push to Talk) button to transmit your voice. The transmit signal icon “P” will display on the screen. b. Hold the unit in a vertical position with the Mic (Microphone)2-3 cm away from the mouth. While holding the PTT button, speak into the microphone in a normal tone of voice. c. Release the PTT button when you have finished transmitting. When a signal is received on the current channel, “A” icon will be displayed on the screen. The unit is continuously in the Receive mode when the unit is turned ON and no transmitting. Note: Both parties must be same channel. 3. Channel settings In standby mode, press the MENU button one time, the current channel will be displayed, press the UP button or DOWN button to adjust the channel. Numbers 1-0 represent channels 1-10 in turn. 4. Volume settings In standby mode, press the MENU button twice, the current volume (L/C/H three gears) will be displayed, press the UP button or DOWN button to adjust the volume. L is low volume; C is medium volume; letter H is high volume. 5. Flashlight function In standby mode, press the Lamp button once the flashlight turns on; press the Lamp button again to turn off. 6. Key lock function In standby mode, press and hold the Lamp /lock button for 1 second, the button will be locked, and character”b” will be display on LED. After the buttons are locked, the UP, DOWN buttons are prohibited to use except for the MANU ,PTT and Lamp /lock functions. If the locked buttons are pressed, the character”b” will be displayed, indicating that the button are locked. Note: After the buttons are locked, long press MENU to turn on and off the unit. 7、key to unlock After the button is locked, press and hold the Lamp /lock button for 1 second, and the unit will return to the standby state. 8、Charging function According to the positive and negative symbols in the battery compartment of the walkie-talkie, install AAA ni mAh 3 pcs rechargeable batteries ,then Plug in the Micro USB cable, the green line flashes up and down on the LED. After charging for about 12 hours, the LED will display “F”, which means the charging is complete. Remark: 1) During charging, to protect the walkie-talkie, it is forbidden to turn it on and operate, unplug the USB cable, and it can be turned on normally. 2) This product does not include rechargeable batteries and Micro USB cables 9. Battery Caution: 1:If you use Alkaline battery ,please use AAA size Alkaline battery ,but don’t attempt to charge alkaline batteries. 2:Please don’t mix old and new batteries ,it will affect the battery lifetime . 3:Do not mix alkaline,standard (carbon-zinc),or rechargeable(Ni-Cd,Ni-MH,etc.)batteries. 4:Alkaline battery have expiry time ,please make sure the battery are valid. 10.Reset the unit Take away one pcs battery from walkie talkie battery compartment,then hold the Menu button and Lock button together meanwhile put back the battery to walkie talkie battery compartment in right polarity,the unit will turn on and display character “8” ,at this time ,release the buttons. FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. USA Frequency CH FREQ(MHz) CTCSS(Hz) 1 462.5625 62.5 2 462.5875 62.5 3 462.6125 62.5 4 462.6375 62.5 5 462.6625 62.5 6 462.6875 62.5 7 462.7125 62.5 8 467.5625 62.5 9 467.5875 62.5 0 467.6125 62.5

Shenzhen Freetalker Industry Co., Ltd. Address: 6/F, Building A, Xinghong Science Park, No.111 of Shuiku Rd., Fenghuanggang, Xixiang, Bao'an, Shenzhen, China Tel: +86 0755 83121380; Fax: +86 0755 83128069 Email: [email protected] QA-FR-170-B 7/29/2014 FCC Authorization Date: 2022-10-19 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We, Shenzhen Freetalker Industry Co., Ltd, the undersigned, hereby authorizes Shenzhen Accurate Technology Co., Ltd. to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Shenzhen Accurate Technology Co., Ltd. on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature: Jianqiang Yang Manager

Shenzhen Freetalker Industry Co., Ltd. Address: 6/F, Building A, Xinghong Science Park, No.111 of Shuiku Rd., Fenghuanggang, Xixiang, Bao'an, Shenzhen, China Tel: +86 0755 83121380; Fax: +86 0755 83128069 Email: [email protected] FCC Confidential Authorization Date: 2022-10-19 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2AHJLQ81 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Shenzhen Freetalker Industry Co., Ltd hereby requests long-term confidential treatment of information accompanying this application as outlined below:  Block Diagram  Schematics  Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature: Printed name: Jianqiang Yang Title: Manager

Shenzhen Freetalker Industry Co., Ltd. Address: 6/F, Building A, Xinghong Science Park, No.111 of Shuiku Rd., Fenghuanggang, Xixiang, Bao'an, Shenzhen, China Tel: +86 0755 83121380; Fax: +86 0755 83128069 Product Similarity Declaration Date: 2022-10-10 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir/Madam, We, Shenzhen Freetalker Industry Co., Ltd., hereby declare that we have a product named as Walkie Talkie, (model: Q81, FCC ID: 2AHJLQ81) was tested by Shenzhen Accurate Technology Co., Ltd., Meanwhile, for our marketing purpose, we would like to list a series model (TQ81, T168, RD633, T821, T319) on reports and certificate, all models are electronic identical, each model has 4 color enclosure, the only difference between all models is model name. We confirm that all information above is true, and we’ll be responsible for all the consequences. Please contact me if you have any question. Sincerely, Signature: Jianqiang Yang Manager Email: [email protected]

Shenzhen Accurate Technology Co., Ltd. FCC ID: 2AHJLQ81 External Photos Page 1 of 13 External Photos For Pink: Shenzhen Accurate Technology Co., Ltd. FCC ID: 2AHJLQ81 External Photos Page 2 of 13 Shenzhen Accurate Technology Co., Ltd. FCC ID: 2AHJLQ81 External Photos Page 3 of 13 Shenzhen Accurate Technology Co., Ltd. FCC ID: 2AHJLQ81 External Photos Page 4 of 13 For Orange Shenzhen Accurate Technology Co., Ltd. FCC ID: 2AHJLQ81 External Photos Page 5 of 13 Shenzhen Accurate Technology Co., Ltd. FCC ID: 2AHJLQ81 External Photos Page 6 of 13 Shenzhen Accurate Technology Co., Ltd. FCC ID: 2AHJLQ81 External Photos Page 7 of 13 For Blue Shenzhen Accurate Technology Co., Ltd. FCC ID: 2AHJLQ81 External Photos Page 8 of 13 Shenzhen Accurate Technology Co., Ltd. FCC ID: 2AHJLQ81 External Photos Page 9 of 13 Shenzhen Accurate Technology Co., Ltd. FCC ID: 2AHJLQ81 External Photos Page 10 of 13 For Green Shenzhen Accurate Technology Co., Ltd. FCC ID: 2AHJLQ81 External Photos Page 11 of 13 Shenzhen Accurate Technology Co., Ltd. FCC ID: 2AHJLQ81 External Photos Page 12 of 13 Shenzhen Accurate Technology Co., Ltd. FCC ID: 2AHJLQ81 External Photos Page 13 of 13

Shenzhen Accurate Technology Co., Ltd. LABEL AND LOCATION Page 1 of 1 FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Shenzhen Accurate Technology Co., Ltd. FCC ID: 2AHJLQ81 Internal Photos Page 1 of 3 Internal photos Shenzhen Accurate Technology Co., Ltd. FCC ID: 2AHJLQ81 Internal Photos Page 2 of 3 Shenzhen Accurate Technology Co., Ltd. FCC ID: 2AHJLQ81 Internal Photos Page 3 of 3 Antenna

Shenzhen Accurate Technology Co., Ltd. Report No.: SZNS220915-41905E-RF-00 Version 26: 2021-11-09 Page 9 of 30 FCC- RF §2.1093 - RF EXPOSURE INFORMATION Applicable Standard According to FCC §2.1093 and §1.1307(b) (3), systems operating under the provisions of this section shall be operated in a manner that ensures the public is not exposed to RF energy level in excess of the communication guidelines. According to KDB 447498 D04 Interim General RF Exposure Guidance SAR-Based Exemption: SAR-based thresholds are derived based on frequency, power, and separation distance of the RF source. The formula defines the thresholds in general for either available maximum timeaveraged power or maximum time-averaged ERP, whichever is greater. Per § 1.1307(b)(3)(i)(B), for single RF sources (i.e., any single fixed RF source, mobile device, or portable device, as defined in paragraph (b)(2) of this section): A single RF source is exempt if: the available maximum time-averaged power or effective radiated power (ERP), whichever is greater, is less than or equal to the threshold P th (mW) described in the following formula. This method shall only be used at separation distances (cm) from 0.5 centimeters to 40 centimeters and at frequencies from 0.3 GHz to 6 GHz (inclusive). P th is given by: Result Frequency (MHz) P th Maximum tune-up ERP Maximum tune-up conducted power Exemption (mW) (dBm) (dBm) (dBm) 462.5625-462.7125 21.17 13.26 3.0 5.15 Compliant 467.5625-467.6125 20.86 13.19 2.0 4.15 Compliant Note: 1. The tune up ERP was declared by the applicant. 2. The antenna gain is 0dBi(-2.15dBd), so the Conducted power was used for evaluation 3. To maintain compliance with the FCC’s RF exposure guidelines, place the equipment at least 0.5cm from nearby persons. Result: Compliant.

Note: This report may contain data that are not covered by the A2LA accreditation and are marked with an asterisk “★”. Shenzhen Accurate Technology Co., Ltd. is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with an asterisk ’*’. Customer model name, addresses, names, trademarks etc. are not considered data. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. Shenzhen Accurate Technology Co., Ltd. 1/F., Building A, Changyuan New Material Port, Science & Industry Park, Nanshan District, Shenzhen, Guangdong, P.R. China Tel: +86 755-26503290 Fax: +86 755-26503396 Web: www.atc-lab.com Version 26: 2021-11-09 Page 1 of 30 FCC- RF TEST REPORT Applicant Name : Shenzhen Freetalker Industry Co., Ltd. Address : 6/F, Building A, Xinghong Science Park, No.111 of Shuiku Rd., Fenghuanggang, Xixiang, Bao'an, Shenzhen, China Report Number : SZNS220915-41905E-RF-00 FCC ID: 2AHJLQ81 Test Standard (s) FCC PART 95 Sample Description Product Type: Walkie Talkie Model No.: Q81 Multiple Model(s) No.: TQ81,T168,RD633,T821,T319 Trade Mark: FREETALKER Date Received: 2022/09/15 Report Date: 2022/10/17 Test Result: Pass* * In the configuration tested, the EUT complied with the standards above. Prepared and Checked By: Approved By: Nick Fang Candy Li EMC Engineer EMC Engineer Shenzhen Accurate Technology Co., Ltd. Report No.: SZNS220915-41905E-RF-00 Version 26: 2021-11-09 Page 2 of 30 FCC- RF TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .................................................................................... 3 OBJECTIVE ................................................................................................................................................................... 3 TEST METHODOLOGY .................................................................................................................................................. 3 MEASUREMENT UNCERTAINTY .................................................................................................................................... 4 TEST FACILITY ............................................................................................................................................................. 4 SYSTEM TEST CONFIGURATION .......................................................................................................................... 5 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 5 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 5 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 5 EXTERNAL I/O CABLE.................................................................................................................................................. 5 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 6 SUMMARY OF TEST RESULTS ............................................................................................................................... 7 TEST EQUIPMENT LIST ........................................................................................................................................... 8 §2.1093 - RF EXPOSURE INFORMATION .............................................................................................................. 9 APPLICABLE STANDARD .............................................................................................................................................. 9 RESULT ........................................................................................................................................................................ 9 FCC §2.1046 & §95.567 - RF OUTPUT POWER ..................................................................................................... 10 APPLICABLE STANDARD ............................................................................................................................................ 10 TEST PROCEDURE ...................................................................................................................................................... 10 TEST DATA ................................................................................................................................................................ 10 FCC §2.1047 & §95.575 - MODULATION CHARACTERISTIC .......................................................................... 11 APPLICABLE STANDARD ............................................................................................................................................ 11 TEST PROCEDURE ...................................................................................................................................................... 11 TEST DATA ................................................................................................................................................................ 11 FCC §2.1049 & §95.573 & §95.579 - AUTHOURIZED BANDWIDTH AND EMISSION MASK...................... 22 APPLICABLE STANDARD ......................................................................…

Text truncated - open the document above for the full version.

Shenzhen Accurate Technology Co., Ltd. Report No.: SZNS220915-41905E-RF Test Photos Page 1 of 1 Photo of Radiated Emission Measurement (Below 1G) Photo of Radiated Emission Measurement (Above 1G)