2AIQACCTLaw Enforcement package beacon

Cell-CAT™ Quick Start GuideCell-CAT™ Quick Start Guide Charging The internal battery may be charged by providing power to the USB-C port. Charge current is typically 250mA max. Dead batteries will fully charge in about 3 hours. Set the power switch to “1” (on) to see charge LED status, orange=charging, green=charged. Battery will continue to charge until full, as long as USB power is provided, even if the power switch is off (0). Set switch to “0” if you do not wish the device to operate while charging. Prolonged USB charging will not harm the device. Charging or powering through a 6 pin connector is also permitted. Input must be 4.7-6.3 VDC. Connecting VHF Antenna If Cell-CAT’s VHF transmitter will be utilized, connect a VHF antenna to the MMCX connector near power switch. Push in firmly until it snaps in place. Pull to remove antenna. For best transmission, the anten- na should be as straight as possible and away from metallic objects. Powering On Slide power switch to “1.” Cell-CAT will illuminate LEDs during initialization: GPS Status • Flashing YELLOW–Acquiring Satellite Fix • Steady GREEN–Satellite Fix Acquired • Solid RED–Unable to Acquire Satellite Fix Cell Connection • Steady BLUE–Initializing Cell-CAT • Flashing YELLOW–Connecting to Cell Network • Steady GREEN–Connected to Cell Network • Solid RED–Unable to connect to Cell network Note: After initialization, GPS, and Cell connections, LEDs will go dark and stay dark until power is turned off and on again. NO LEDs will light under any con- dition if unit is set to “covert” mode. Configuration To configure Cell-CAT refer to Cell-CAT Program- ming Guide. Cellular Connectivity Cell-CAT utilizes 4G LTE-M cellular connectivity to report data and may be configured via iOS app or server using cellular connection. Cleaning To clean Cell-CAT, use a damp towel with mild soap or rubbing alcohol. Do not rinse in water. Cell-CAT is not water-resistant. Warning Cell-CAT contains a Lithium-Ion battery pack and requires proper disposal. Do not dispose of in fire or incinerate. Keep-out area Cell-CAT has internal GPS and cellular anten- nas. For best signal reception, keep metallic ob- jects away from areas bounded by dashed-lines on top and bottom. VHF Transmitter Specifications 150.000-173.390 MHz in 2.5 KHz steps (136.000-173.390 MHz for Federal users) Output power: settable 0 (off) to 100 mW 216.0125-216.9875 MHz in 12.5 KHz steps Output power: settable 0 (off) to 50 mW Training, Support, and Service For training, support, and service, please con- tact Special Services Group, LLC, 1-209-682- 5026. Cell-CAT™ Quick Start GuideCell-CAT™ Quick Start Guide NOTICE: THIS PRODUCT IS RESTRICTED TO LAW ENFORCEMENT USE FCC Information FCC ID: 2AIQACCT Contains FCC ID: R17ME310G1WW, Contains IC: 5131A-ME310G1WW NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pur- suant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the follow- ing measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Sierra Innotek, Inc. may void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device may not interfere with TV reception or Federal Government radar. This transmitter is authorized by rule under the Low Power Radio Service (47 CFR Part 95) and must not cause harmful interference to TV reception or to the United States Air Force Space Surveillance System operating in the 216.88–217.08 MHz band. With the exception of automated maritime telecommunications system (AMTS) devices, you do not need an FCC license to operate this transmitter. This transmitter may only be used to provide: auditory assistance to persons with disabilities, persons who require language translation, or persons in educational settings; health care services to the ill; law enforcement tracking services under agreement with a law enforcement agency; or AMTS network control communications. Two-way voice communications and all other types of uses not men- tioned above are expressly prohibited. RF Exposure warning statements: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End us- ers must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and the body of the user or nearby persons. This device complies with FCC OET bulletin 65 radiation exposure limits set forth for an uncontrolled environment. The information in this guide may change without notice. The manufacturer assumes no responsibility for any errors that may appear in this guid…

Text truncated - open the document above for the full version.

Letter of Authorization and Anti- Drug Statement Applicant Name: Sierra Innotek, Inc Address: 3013 Alhambra Drive, Cameron Park, CA. 95682 Product Name: Cell-CAT Model Number: CCT FCC ID: 2AIQACCT We authorize: CETECOM Inc., to act on our behalf on all matters concerning the above named equipment. We declare that CETECOM Inc. is allowed to forward all information related to the approval project to the Federal Communications Commission and discuss any issues concerning the approval application. The applicant must certify that neither the applicant nor any party to the application is subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti- Drug Abuse Act of 1988, 21 U.S.C. § 862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a "party" for these purposes. Does the applicant or authorized agent so certify? ☒ Yes I certify that I am authorized to sign this application. All of the statements herein and the exhibits attached hereto, are true and correct to the best of my knowledge and belief. In accepting a Grant of Equipment Authorization as a result of the representations made in this application, the applicant is responsible for (1) labeling the equipment with the exact FCC ID specified in this application, (2) compliance statement labeling pursuant to the applicable rules, and (3) compliance of the equipment with the applicable technical rules. If the applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC's technical requirements. Authorizing an agent to sign this application, is done solely at the applicant's discretion; however, the applicant remains responsible for all statements in this application. If an agent has signed this application on behalf of the applicant, a written letter of authorization which includes information to enable the agent to respond to the above section 5301 (Anti-Drug Abuse) Certification statement has been provided by the applicant. It is understood that the letter of authorization must be submitted to the FCC upon request, and that the FCC reserves the right to contact the applicant directly at any time. Signature of Authorized Person Filing: Title: President Date: June 19, 2023

3013 Alhambra Drive Cameron Park, CA. 95682 Federal Communication Commission 7435 Oakland Mills Road Columbia, MD 21046 June 19, 2023 Attestation Statement according to 2.911(d)(5)(i) and 2.911(d)(5)(ii) FCC ID: 2AIQACCT TO WHOM IT MAY CONCERN: Hereby we certify that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Further we certify that, as of the date of the filing of the application, Sierra Innotek, Inc is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, , President (signature & company stamp) Sierra Innotek, Inc 3013 Alhambra Drive Cameron Park, CA. 95682 Steve Palmer 530-672-2366 [email protected] For information on Covered equipment, refer: • 986446 D01 Covered Equipment v01 • FCC 22-84 • List of Equipment and Services Covered By Section 2 of The Secure Networks Act | Federal Communications Commission (fcc.gov)

Sierra Innotek, Inc. 3013 Alhambra Drive Cameron Park, CA. 95682 Federal Communication Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA August 2, 2023 Attestation Statement according to 2.911(d)(7) FCC ID: 2AIQACCT TO WHOM IT MAY CONCERN: Sierra Innotek, Inc with FCC Registration Number (FRN) 0025648635 Certifies that, as of the date of this filing of the application with the TCB, Sierra Innotek, Inc is our designated US agent for service of process for the above referenced FCC ID. Sierra Innotek, Inc accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. Sierra Innotek, Inc with FCC Registration Number (FRN) 0025648635 Accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above referenced FCC ID. Sincerely , President (signature & company stamp) 3013 Alhambra Drive Cameron Park, CA. 95682 Steve Palmer 530-672-2366 [email protected] , President (signature & company stamp) 3013 Alhambra Drive Cameron Park, CA. 95682 Steve Palmer 530-672-2366 [email protected]

Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21048 Date: June 19, 2023 Subject: Request for Permanent Confidentiality FCC ID: 2AIQACCT To Whom It May Concern: In accordance with §0.457(d) and §0.459 of CFR 47, and KDB 726920, Full Company Name hereby requests permanent confidentiality for documents filed under the following exhibit types: 1. Block Diagram 2. Schematic Diagram 3. Part List 4. Operational Description These items contain detailed system and equipment description and related information about the product which Sierra Innotek, Inc considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from which future technological products will evolve, Sierra Innotek, Inc also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. We are aware that exhibit types cover letters, attestations, label document, test reports, RF exposure information (SAR and MPE reports), cannot be requested to be classified confidential and are thus subject to publication, as will be documents of all other exhibits types for which we have not requested a confidentiality classification. Best Regards, _______________________________ Signature Name: Steve Palmer Title: President Company Name: Sierra Innotek, Inc. Address: 3013 Alhambra Drive, Cameron Park, CA. 95682

Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21048 Date: June 19, 2023 Subject: Request for Short Term Confidentiality FCC-ID: 2AIQACCT To Whom It May Concern: In accordance with §0.457(d) and §0.459 of CFR 47, Sierra Innotek, Inc. hereby requests short term confidentiality for documents filed under the following exhibit types: 1. External Photographs 2. Internal Photographs 3. User / Instruction Manual 4. Test Set-up Photographs until the product will be publicly announced. Short term confidentiality release date / period: 180 days These items contain detailed system and equipment description and related information about the product which Sierra Innotek, Inc. considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from which future technological products will evolve, Sierra Innotek, Inc. also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. We are informed and aware of our obligation that we have to inform the involved TCB in written and in due time if we intend to market the product prior to the above specified confidentiality release date so that the short term confidentiality classification can be reset prior to product launch. We are aware that exhibit types cover letters, attestations, label document, test reports, RF exposure information (SAR and MPE reports), cannot be requested to be classified confidential and are thus subject to publication, as will be documents of all other exhibits types for which we have not requested a confidentiality classification. Best Regards, Name: Steve Palmer Title: President Company Name: Sierra Innotek, Inc. Address: 3013 Alhambra Drive, Cameron Park, CA. 95682

FCC and Regulatory Electronic Labeling Sierra Innotek, Inc. Cell-CAT (FCC ID: 2AIQACCT) To access FCC ID and statement, user connects to device and sees “Congure” screen Click 1: user taps “Device Details” button and is presented with Device Details screen Click 2: user taps “FCC and Regulatory” button and is presented with “FCC and regulatory screen. Using nger, user scrolls to access FCC statements Top of FCC informationMiddle of FCC information Bottom of FCC information

RF Exposure Evaluation Report FOR: Sierra Innotek, Inc. Brand: Sierra Innotek, Inc. Marketing Name: Cell-CAT Model: Cell-CAT Product Description: Tracking beacon for law enforcement and VHF alarm transmitter FCC ID: 2AIQACCT Per: CFR Part Part1 (1.1307 & 1.1310), Part 2 (2.1091), FCC KDB 447498 D01 General RF Exposure Guidance v06 Report number: EMC_INNOT_003_23001_FCC _RF_Exposure DATE: 9/7/2023 A2LA Accredited IC recognized # 3462B CETECOM Inc. 411 Dixon Landing Road  Milpitas, CA 95035  U.S.A. Phone: + 1 (408) 586 6200  Fax: + 1 (408) 586 6299  E-mail: [email protected]  http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2905571 V5.0 2015-10-27 © Copyright by CETECOM Test Report #: EMC_KPTRK_040_23001_FCC_ISED_RF_Exposure FCC ID: 2AIQACCT Date of Report: 9/7/2023 Page 2 of 10 Page 2 of 10 TABLE OF CONTENTS 1 Assessment ................................................................................................................................................ 3 2 Administrative Data .................................................................................................................................... 4 2.1 Identification of the Testing Laboratory Issuing the Test Report ......................................................... 4 2.2 Identification of the Client / Manufacturer ............................................................................................ 4 2.3 Identification of the Manufacturer ........................................................................................................ 4 3 Equipment under Assessment .................................................................................................................... 5 4 RF Exposure Limits and FCC Basic Rules ................................................................................................. 6 4.1 § 2.1091(c)(1) ..................................................................................................................................... 6 4.2 § 2.1091(c)(2) ..................................................................................................................................... 6 4.3 § 1.1307(b)(3)(i) .................................................................................................................................. 6 4.4 § 1.1307(b)(3)(ii) ................................................................................................................................. 7 4.5 Maximum Permissible Exposure (MPE) .............................................................................................. 7 5 Evaluations ................................................................................................................................................. 9 5.1 Single RF Sources Subject to Routine Environmental Evaluation ....................................................... 9 6.2 Maximum Permissible Exposure (MPE) Evaluation ............................................................................ 9 6.3 Multiple RF sources ............................................................................................................................ 9 7 Revision History ....................................................................................................................................... 10 Test Report #: EMC_KPTRK_040_23001_FCC_ISED_RF_Exposure FCC ID: 2AIQACCT Date of Report: 9/7/2023 Page 3 of 10 Page 3 of 10 1 Assessment This RF Exposure evaluation report provides evidence for compliance of the equipment (as identified in section 3 of this test report) with the RF Exposure limits for mobile devices as defined in FCC CFR Part 1 1.1307, 1.1310, and Part 2 (2.1091) under worst case conditions (measured or rated RF output power including tune-up tolerance, antenna gain, the distance towards the human body, multiple transmitter information as presented by the applicant). In addition, maximum antenna gain or minimum distance towards the human body is calculated respectively, where relevant. The device meets the limits stipulated by the above given FCC rule parts based on available specifications for worst-case conditions at a separation distance greater than 20cm to the body. Company Description Model Sierra Innotek, Inc. Tracking beacon for law enforcement and VHF alarm transmitter Cell-CAT Responsible for Testing Laboratory: 9/7/2023 Compliance Stoecker, Arndt (Director of Regulatory Services) Date Section Name Signature Responsible for the Report: 9/7/2023 Compliance Lui, Chin Ming (Associate Test Engineer) Date Section Name Signature Test Report #: EMC_KPTRK_040_23001_FCC_ISED_RF_Exposure FCC ID: 2AIQACCT Date of Report: 9/7/2023 Page 4 of 10 Page 4 of 10 2 Administrative Data 2.1 Identification of the Testing Laboratory Issuing the Test Report Company Name: CETECOM Inc. Department: Compliance Street Address: 411 Dixon Landing Road City/Zip Code Milpitas, CA 95035 Country USA Telephone: +1 (408) 586 6200 Fax: +1 (408) 586 6299 EMC Lab Manager: Stoecker, Arndt Responsible Project Leader: Saman, Rami 2.2 Identification of the Client / Manufacturer Applicant’s Name: Sierra Innotek, Inc. Street Address: 3013 Alhambra Drive City/Zip Code Cameron Park, CA 95682 Country USA 2.3 Identification of the Manufacturer Manufacturer’s Name: Same as Client /----------------- Manufacturers Address: ----------------- City/Zip Code ----------------- Country ----------------- Test Report #: EMC_KPTRK_040_23001_FCC_ISED_RF_Exposure FCC ID: 2AIQACCT Date of Report: 9/7/2023 Page 5 of 10 Page 5 of 10 3 Equipment under Assessment Brand: Sierra Innotek, Inc. Model: Cell-CAT Marketing name: Cell-CAT FCC-ID : 2AIQACCT HW Version : 1 SW Version : 6 Product Description: Tracking beacon for law enforcement and VHF alarm transmitter Frequency Range/number of channels:  Cellular: o LTE Cat-M1 Band 2: 1850 – 1910 MHz o LTE Cat-M1 Band 4: 1710 – 1755 MHz o LTE Cat-M1 Band 12: 699 – 716 MHz  BT LE: o N…

Text truncated - open the document above for the full version.

A2LA Accredited IC recognized # 3462B-2 CETECOM Inc. 411 Dixon Landing Road  Milpitas, CA 95035  U.S.A. Phone: + 1 (408) 586 6200  Fax: + 1 (408) 586 6299  E-mail: [email protected]  http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2905571 V4.0 2012-07-25 The BLUETOOTH trademarks are owned by Bluetooth SIG, Inc., U.S.A. and licensed to CETECOM Inc. © Copyright by CETECOM FCC Test Report FOR: Sierra Innotek, Inc. Model Name: Cell-CAT Product Description: Tracking beacon for law enforcement and VHF alarm transmitter FCC ID: 2AIQACCT Applied Rules and Standards: 47 CFR: Part 90.217 REPORT #: EMC_INNOT_003_23001_FCC_90.217 DATE: 2023-09-07 Test Report #: EMC_INNOT_003_23001_FCC_90.217 FCC ID: 2AIQACCT Date of Report 2023-09-07 Page 2 of 45 TABLE OF CONTENTS 1 ASSESSMENT .............................................................................................................................................................. 3 2 ADMINISTRATIVE DATA .............................................................................................................................................. 4 2.1 IDENTIFICATION OF THE TESTING LABORATORY ISSUING THE EMC TEST REPORT ............................................................................. 4 2.2 IDENTIFICATION OF THE CLIENT ............................................................................................................................................. 4 2.3 IDENTIFICATION OF THE MANUFACTURER ................................................................................................................................ 4 3 EQUIPMENT UNDER TEST (EUT) .................................................................................................................................. 5 3.1 EUT SPECIFICATIONS .......................................................................................................................................................... 5 3.2 EUT SAMPLE DETAILS.......................................................................................................................................................... 6 3.3 SUPPORT EQUIPMENT ......................................................................................................................................................... 6 3.4 TEST SAMPLE CONFIGURATION ............................................................................................................................................. 6 3.5 MODE OF OPERATION ......................................................................................................................................................... 6 4 SUBJECT OF INVESTIGATION ....................................................................................................................................... 7 5 MEASUREMENT RESULTS SUMMARY ......................................................................................................................... 7 6 MEASUREMENT UNCERTAINTY .................................................................................................................................. 8 6.1 ENVIRONMENTAL CONDITIONS DURING TESTING: ..................................................................................................................... 8 6.2 DATES OF TESTING:............................................................................................................................................................. 8 6.3 DECISION RULE: ................................................................................................................................................................. 8 7 MEASUREMENT PROCEDURES .................................................................................................................................... 9 7.1 RADIATED MEASUREMENT ................................................................................................................................................... 9 7.2 RF CONDUCTED MEASUREMENT PROCEDURE ........................................................................................................................ 11 8 TEST RESULT DATA ................................................................................................................................................... 12 8.1 RF OUTPUT POWER .......................................................................................................................................................... 12 8.2 MODULATION CHARACTERISTICS ......................................................................................................................................... 18 8.3 OCCUPIED BANDWIDTH ..................................................................................................................................................... 20 8.4 SPURIOUS EMISSIONS AT ANTENNA TERMINALS ..................................................................................................................... 25 8.5 FIELD STRENGTH OF SPURIOUS RADIATION ............................................................................................................................ 38 8.6 FREQUENCY STABILITY ....................................................................................................................................................... 41 9 TEST SETUP PHOTOS ................................................................................................................................................. 44 10 TEST EQUIPMENT AND ANCILLARIES USED FOR TESTING ......................................................................................... 44 11 REVISION HISTORY ................................................................................................................................................... 45 Test Report #: EMC_INNOT_003_23001_FCC_90.217 FCC ID: 2AIQACCT Date of Report 2023-09-07 Page 3 of 45 1 …

Text truncated - open the document above for the full version.

A2LA Accredited IC recognized # 3462B-2 CETECOM Inc. 411 Dixon Landing Road  Milpitas, CA 95035  U.S.A. Phone: + 1 (408) 586 6200  Fax: + 1 (408) 586 6299  E-mail: [email protected]  http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2905571 V4.0 2012-07-25 The BLUETOOTH trademarks are owned by Bluetooth SIG, Inc., U.S.A. and licensed to CETECOM Inc. © Copyright by CETECOM FCC Test Report FOR: Sierra Innotek Model Name: Cell-CAT Product Description: Tracking beacon for law enforcement and VHF alarm transmitter FCC ID: 2AIQACCT Applied Rules and Standards: 47 CFR: Part 95 Subpart G for Low Power Radio Service REPORT #: EMC_INNOT_003_23001_FCC_95 DATE: 2023-09-07 Test Report #: EMC_INNOT_003_23001_FCC_95 FCC ID: 2AIQACCT Date of Report 2023-09-07 Page 2 of 41 TABLE OF CONTENTS 1 ASSESSMENT .............................................................................................................................................................. 3 2 ADMINISTRATIVE DATA .............................................................................................................................................. 4 2.1 IDENTIFICATION OF THE TESTING LABORATORY ISSUING THE EMC TEST REPORT ............................................................................. 4 2.2 IDENTIFICATION OF THE CLIENT ............................................................................................................................................. 4 2.3 IDENTIFICATION OF THE MANUFACTURER ................................................................................................................................ 4 3 EQUIPMENT UNDER TEST (EUT) .................................................................................................................................. 5 3.1 EUT SPECIFICATIONS .......................................................................................................................................................... 5 3.2 EUT SAMPLE DETAILS.......................................................................................................................................................... 6 3.3 SUPPORT EQUIPMENT ......................................................................................................................................................... 6 3.4 TEST SAMPLE CONFIGURATION ............................................................................................................................................. 6 3.5 MODE OF OPERATION ......................................................................................................................................................... 6 4 SUBJECT OF INVESTIGATION ....................................................................................................................................... 9 5 MEASUREMENT RESULTS SUMMARY ......................................................................................................................... 9 6 MEASUREMENT UNCERTAINTY ................................................................................................................................ 10 6.1 ENVIRONMENTAL CONDITIONS DURING TESTING: ................................................................................................................... 10 6.2 DATES OF TESTING:..............…

Text truncated - open the document above for the full version.