2AJE7SMC-WEX04Wireless I/O Device

No.EX※※-OMX0008 PRODUCT NAME SMC Wireless System Compact remote MODEL/ Series/ Product Number EX600-WD□ (Remote) Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of "Caution", "Warning" or "Danger". They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC)*1), and other safety regulations. *1) ISO 4414: Pneumatic fluid power -- General rules relating to systems. ISO 4413: Hydraulic fluid power -- General rules relating to systems. IEC 60204-1: Safety of machinery -- Electrical equipment of machines .(Part 1: General requirements) ISO 10218: Manipulating industrial robots -Safety. etc. Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1. The compatibility of the product is the responsibility of the person who designs the equipment or decides its specifications. Since the product specified here is used under various operating conditions, its compatibility with specific equipment must be decided by the person who designs the equipment or decides its specifications based on necessary analysis and test results. The expected performance and safety assurance of the equipment will be the responsibility of the person who has determined its compatibility with the product. This person should also continuously review all specifications of the product referring to its latest catalog information, with a view to giving due consideration to any possibility of equipment failure when configuring the equipment. 2. Only personnel with appropriate training should operate machinery and equipment. The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. 3. Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2. When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any appropriate source is cut, and read and understand the specific product precautions of all relevant products carefully. 3. Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction. 4. Contact SMC beforehand and take special consideration of safety measures if the product is to be used in any of the following conditions. 1. Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2. Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping, vehicles, military, medical treatment, combustion and recreation, or equipment in contact with food and beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or other applications unsuitable for the standard specifications described in the product catalog. 3. An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. Safety Instructions Caution 1.The product is provided for use in manufacturing industries. The product herein described is basically provided for peaceful use in manufacturing industries. If considering using the product in other industries, consult SMC beforehand and exchange specifications or a contract if necessary. If anything is unclear, contact your nearest sales branch. Limited warranty and Disclaimer/Compliance Requirements The product used is subject to the following "Limited warranty and Disclaimer" and "Compliance Requirements". Read and accept them before using the product. Limited warranty and Disclaimer 1. The warranty period of the product is 1 year in service or 1.5 years after the product is delivered, whichever is first.2) Also, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch. 2. For any failure or damage reported within the warranty period which is clearly our responsibility, a replacement product or necessary parts will be provided. This limited warranty applies only to our product independently, and not to any other damage incurred due to the failure of the product. 3. Prior to using SMC products, please read and understand the warranty terms and disclaimers noted in the specified catalog for the particular products. 2) Vacuum pads are excluded from this 1 year warranty. A vacuum pad is a consumable part, so it is warranted for a year after it is delivered. Also, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to the deterioration of rubber material are not covered by the limited warranty. Compliance Requirements 1. The use of SMC products with production equipment for the manufacture of weapons of mass destruction (WMD) or any other weapon is strictly prohibited. 2. The exports of SMC products or technology from one country to another are governed by the relevant security laws and regulation of the countries involved in the transaction. Prior to the shipment of a SMC product to another country, assure that all local rules governing t…

Text truncated - open the document above for the full version.

FCC ID：2AJE7SMC-WEX04 1/8 EX600-WDXA1 Front side EX600-WDXA1 Back side FCC ID：2AJE7SMC-WEX04 2/8 EX600-WDXA1 Left side EX600-WDXA1 Right side FCC ID：2AJE7SMC-WEX04 3/8 EX6000-WDXA1 Top side EX600-WDXA1 Bottom side FCC ID：2AJE7SMC-WEX04 4/8 EX600-WDXA1 Overview FCC ID：2AJE7SMC-WEX04 5/8 EX600-WDYA1 Front side EX600-WDYA1 Back side FCC ID：2AJE7SMC-WEX04 6/8 EX600-WDYA1 Left side EX600-WDYA1 Right side FCC ID：2AJE7SMC-WEX04 7/8 EX6000-WDYA1 Top side EX600-WDYA1 Bottom side FCC ID：2AJE7SMC-WEX04 8/8 EX600-WDYA1 Overview

FCC ID：2AJE7SMC-WEX04 1/11 EX600-WDXA1 InSide view FCC ID：2AJE7SMC-WEX04 2/11 EX6000-WDXA1 Inside view FCC ID：2AJE7SMC-WEX04 3/11 EX600-WDXA1 Inside view FCC ID：2AJE7SMC-WEX04 4/11 EX600-WDYA1 Inside view FCC ID：2AJE7SMC-WEX04 5/11 EX600-WDYA1 Inside view FCC ID：2AJE7SMC-WEX04 6/11 EX600-WDYA1 Inside view FCC ID：2AJE7SMC-WEX04 7/11 NFC antenna board assembly FCC ID：2AJE7SMC-WEX04 8/11 Main board (input) assembly FCC ID：2AJE7SMC-WEX04 9/11 Main board (output) assembly FCC ID：2AJE7SMC-WEX04 10/11 FCC ID：2AJE7SMC-WEX04 11/11 Radio module board assembly Model variation EX600-WDXA1 EX600-WDYA1 Main board (input) assembly × － Main board (output) assembly － × Radio module board assembly × × NFC antenna board assembly × × × contained － not contained

This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. This Report shall not be reproduced, except in full without written approval of the laboratory. SMC Corporation EX600-WDYA1 with EX600-WDYE1 FCC 15.247:2020 2400 - 2483.5 MHz FHSS Transceiver Report: PCTE0001.1, Issue Date: July 31, 2020 NVLAP LAB CODE: 200676-0 CERTIFICATE OF TEST 2018-09-14 Product compliance is the responsibility of the client; therefore, the tests and equipment modes of operation represented in this report were agreed upon by the client, prior to testing. The results of this test pertain only to the sample(s) tested. The specific description is noted in each of the individual sections of the test report supporting this certificate of test. This report reflects only those tests from the referenced standards shown in the certificate of test. It does not include inspection or verification of labels, identification, marking or user information. As indicated in the Statement of Work sent with the quotation, Element’s standard process is to always use the latest published version of the test methods even when earlier versions are cited in the test specification. Issuance of a purchase order was de facto acceptance of this approach. Otherwise, the client would have advised Element in writing of the specific version of the test methods they wanted applied to the subject testing. Last Date of Test: June 18, 2020 SMC Corporation EUT: EX600-WDYA1 with EX600-WDYE1 Radio Equipment Testing Standards Specification Method FCC 15.247:2020 ANSI C63.10:2013, KDB 558074 Results Method Clause Test Description Applied Results Comments 6.2 Powerline Conducted Emissions (Transmitter) No N/A Not requested for this system level approval. 6.5, 6.6 Spurious Radiated Emissions Yes Pass 7.5 Duty Cycle No N/A Not requested for this system level approval. 7.8.2 Carrier Frequency Separation No N/A Not requested for this system level approval. 7.8.3 Number of Hopping Frequencies No N/A Not requested for this system level approval. 7.8.4 Dwell Time No N/A Not requested for this system level approval. 7.8.5 Output Power No N/A Not requested for this system level approval. 7.8.5 Equivalent Isotropic Radiated Power No N/A Not requested for this system level approval. 7.8.6 Band Edge Compliance No N/A Not requested for this system level approval. 7.8.6 Band Edge Compliance - Hopping Mode No N/A Not requested for this system level approval. 7.8.7 Occupied Bandwidth No N/A Not requested for this system level approval. 7.8.8 Spurious Conducted Emissions No N/A Not requested for this system level approval. 11.10.2 Power Spectral Density No N/A Not required for FHSS devices. Deviations From Test Standards None Approved By: Victor Ratinoff, Operations Manager Report No. PCTE0001.12/17 REVISION HISTORY 2018.07.17 Revision Number Description Date (yyyy-mm-dd) Page Number 00 None Report No. PCTE0001.13/17 ACCREDITATIONS AND AUTHORIZATIONS 2019.03.08 United States FCC - Designated by the FCC as a Telecommunications Certification Body (TCB). Certification chambers, Open Area Test Sites, and conducted measurement facilities are listed with the FCC. A2LA - Accredited by A2LA to ISO / IEC 17065 as a product certifier. This allows Element to certify transmitters to FCC and IC specifications. NVLAP - Each laboratory is accredited by NVLAP to ISO 17025 Canada ISED - Recognized by Innovation, Science and Economic Development Canada as a Certification Body (CB) and as a CAB for the acceptance of test data. European Union European Commission – Within Element, we have a EU Notified Body validated for the EMCD and RED Directives. Australia/New Zealand ACMA - Recognized by ACMA as a CAB for the acceptance of test data. Korea MSIT / RRA - Recognized by KCC’s RRA as a CAB for the acceptance of test data. Japan VCCI - Associate Member of the VCCI. Conducted and radiated measurement facilities are registered. Taiwan BSMI – Recognized by BSMI as a CAB for the acceptance of test data. NCC - Recognized by NCC as a CAB for the acceptance of test data. Singapore IDA – Recognized by IDA as a CAB for the acceptance of test data. Israel MOC – Recognized by MOC as a CAB for the acceptance of test data. Hong Kong OFCA – Recognized by OFCA as a CAB for the acceptance of test data. Vietnam MIC – Recognized by MIC as a CAB for the acceptance of test data. SCOPE For details on the Scopes of our Accreditations, please visit: https://www.nwemc.com/emc-testing-accreditations Report No. PCTE0001.14/17 FACILITIES 2019.03.08 California Labs OC01-17 41 Tesla Irvine, CA 92618 (949) 861-8918 Minnesota Labs MN01-10 9349 W Broadway Ave. Brooklyn Park, MN 55445 (612)-638-5136 Oregon Labs EV01-12 6775 NE Evergreen Pkwy #400 Hillsboro, OR 97124 (503) 844-4066 Texas Labs TX01-09 3801 E Plano Pkwy Plano, TX 75074 (469) 304-5255 Washington Labs NC01-05 19201 120 th Ave NE Bothell, WA 98011 (425)984-6600 NVLAP NVLAP Lab Code: 200676-0 NVLAP Lab Code: 200881-0 NVLAP Lab Code: 200630-0 NVLAP Lab Code:201049-0 NVLAP Lab Code: 200629-0 Innovation, Science and Economic Development Canada 2834B-1, 2834B-3 2834E-1, 2834E-3 2834D-1 2834G-1 2834F-1 BSMI SL2-IN-E-1154R SL2-IN-E-1152R SL2-IN-E-1017 SL2-IN-E-1158R SL2-IN-E-1153R VCCI A-0029 A-0109 A-0108 A-0201 A-0110 Recognized Phase I CAB for ISED, ACMA, BSMI, IDA, KCC/RRA, MIC, MOC, NCC, OFCA US0158 US0175 US0017 US0191 US0157 Report No. PCTE0001.15/17 MEASUREMENT UNCERTAINTY TMU.2015.07.10 Measurement Uncertainty When a measurement is made, the result will be different from the true or theoretically correct value. The difference is the result of tolerances in the measurement system that cannot be completely eliminated. To the extent that technology allows us, it has been our aim to minimize this error. Measurement uncertainty is a statistical expression of measurement error qualified by a probability distribution. A measurement uncertainty estimation has been performed for each test …

Text truncated - open the document above for the full version.

photo PSA-ESCI 2020.04.03.0 photos PSA-ESCI 2020.04.03.0 SRE (6).JPG SRE (7).JPG -7 SPURIOUS RADIATED EMISSIONS photo PSA-ESCI 2020.04.03.0 photos PSA-ESCI 2020.04.03.0 SRE (8).JPG SRE (9).JPG -9 SPURIOUS RADIATED EMISSIONS photo PSA-ESCI 2020.04.03.0 photos PSA-ESCI 2020.04.03.0 SRE (10).JPG SRE (11).JPG SPURIOUS RADIATED EMISSIONS photo PSA-ESCI 2020.04.03.0 photos PSA-ESCI 2020.04.03.0 SRE (12).JPG SRE (13).JPG -13 SPURIOUS RADIATED EMISSIONS photo PSA-ESCI 2020.04.03.0 photos PSA-ESCI 2020.04.03.0 SRE (14).JPG SRE (15).JPG -15 SPURIOUS RADIATED EMISSIONS photo PSA-ESCI 2020.04.03.0 photos PSA-ESCI 2020.04.03.0 SRE (3).JPG SRE (5).JPG -5 SPURIOUS RADIATED EMISSIONS