2AJZH-PE932Power Meter

STRYD RUNNING WITH POWER USER MANUAL This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE:The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help -This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. OVERVIEW Strydisthefirstwearabledevicetomeasurerunningpower.Itgives runnersawaytoaccuratelymeasuretrainingintensityacrossvaried terrain.Strydprovidesreal-timefeedbackonexertion,form,economy,and fatigueviathesportswatchesandmobiledevicesathletesalreadyuse. Strydunlockswaysforrunnerstoimproverunning. WHY STRYD Better form, better efficiency Train in the right zone Perfect pace for the perfect race GETTING STARTED 1.Clipthedeviceonyourleftorrightshoe,withthedeviceLEDfacing upandthesmallersideofthedevicepointingtowardsyourtoe. 2.ConnectthedevicewithyoursportswatchortheSTRYDsmart phonemobileapp. 3.Beginyourworkout. 4.Afteryoufinishyourworkout,uploadyourworkoutdatathrough STRYDsmartphonemobileappor3rd-partysportswatchsoftware. SPECIFICATIONS POWER METRICS Running efficiency, training intensity, Run form, pace & distance INSTALLATION Shoe clip DIMENSIONS 4.05cm x 29.95cm x 10.5cm WEIGHT 7g WATER RESISTANCE 30 mins @ 1.5 meter BATTERY LIFETIME One month per charge COMMUNICATION Bluetooth, ANT+ OPERATING TEMPERATURE -20 ~ 60°C CONNECT TO SPORTS WATCH 1.Strydsupportspower-enabledsportswatches,includingbutnotlimited to,GarminConnectIQ-compatiblewatchesandXTseries,SuuntoAmbit andSpaartanseries,andPolarVantageseriesandV800. 2.Pleasefollowtheinstructionsfromthesportswatch’susermanualto connectSTRYDwithyoursportswatch. CONNECTING TO MOBILE PHONE STRYDisequippedwithamobilephoneapplication,whichsupportsreal- timecoaching&feedbacktorunners,aswellaspost-runanalysis. ToconnecttheSTRYDdevicewiththemobileapplication: 1.Clipthedevicetoyourshoe. 2.TurnontheSTRYDmobileapplication. 3.Startyourworkout. 4.ThemobileapplicationwillautomaticallyconnectwithyourSTRYD device. POST-RUN ANALYSIS 1.Workoutupload:TheSTRYDmobilephoneappautomaticallyuploads yourrundatatotheSTRYDonlinetrainingcenter.Ifyouuseyourpower- enabledsportswatch,pleaseusethethe3rd-partysportswatch softwaretouploadthedata,ortheStrydConnectIQapponcompatible Garminwatches. 2.Post-runanalysis:UsingtheSTRYDonlinetrainingcenterorsupported 3rd-partyonlinetrainingcenter,youcanreviewyourrun-trainingdata, andthenadjustyourtrainingplanaccordingly. CHARGING BATTERY Strydusesapre-installedrechargeableLi-ionbattery,whichsupports roughlyamonthofusepercharge,dependingdailyrunduration. Whenthebatteryenergyislow,a“lowbattery”icondisplaysontheStryd mobileapp. Tochargethebattery,placeStrydonthecenterpointoftheincluded wiredchargingstation.Alightwillilluminate,indicatingthatbattery chargingisinprogress. NOTE:Strydwillnotchargeintemperatureslowerthan0C/32F. WARNING: Thisisnotamedicaldeviceandisnotrecommendedforusebypersons withseriousheartconditionsorphysicalinjury.Consultyourphysician beforebeginninganyexerciseprogram.

Stryd 2200 Central Ave STE H Boulder, Colorado 80301 UNITED STATES Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 02- 07- 2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AJZH-PE932 [ Stryd] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Jamie Williamson)

2.911(d)(7)USAAgentv1.2 Section2.911(d)(7)USA Agentfor Serviceof Process ProductName:PowerMeter FCC ID : 2AJZH-PE932 Model(s):PE932 2.911(d)(7)USADesignatedAgentforServiceof Process We, [Stryd] (“the applicant”) designate [Stryd] NOTE1 for the purpose of accepting service of process on behalf of the applicant. Applicantconsent:We Acknowledgeour consentto acceptserviceof processin the UnitedStatesfor mattersrelatedto the applicableequipment,and at the physicalU.S. addressand emailaddressof the designatedagentand acknowledgeour acceptanceof our obligationto maintainan agent for serviceof processin the United Statesfor no less than one year after either the granteehas permanentlyterminated all marketingand importationof the applicableequipmentwithinthe U.S., or the conclusionof any Commission-relatedadministrativeor judicialproceedinginvolving the equipment,whicheveris later. Agentobligation:We Acknowledgeour obligationto acceptserviceof processin the UnitedStatesfor mattersrelatedto the applicableequipmentat our physicalU.S. addressand email addressfor no less than one year after eitherthe granteehas permanentlyterminatedall marketingand importationof the applicableequipment within the U.S., or the conclusionof any Commission-relatedadministrativeor judicial proceedinginvolvingthe equipment,whicheveris later. USA Agent & Applicant Companyname:Stryd Address:2200 CentralAve STE H Boulder,Colorado80301UNITEDSTATES ContactName:JamieWilliamson TelephoneNo: +18456560932 Email:[email protected] Signature: Date: Feb.07,2023 NOTE1: An applicantlocatedin the UnitedStatesmay designateitself as the agent for service of process. 2.911(d)(7)USAAgentv1.2 Reference;FederalRegisterdocument2022-28263publishedon02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-nation al-security-threats-to-the-communications-supply-chain-through-the

Stryd Agent Authorization Company: Stryd Address: 2200 Central Ave STE H Boulder, Colorado 80301 UNITED STATES Product Name: Power Meter Model Number(s): PE932 Product Description: Power Meter We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2023-01-11 Name: Jamie Williamson Company: Stryd

Stryd OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USA Date: 2023-01-04 Subject;RequestforConfidentiality FCCID:2AJZH-PE932 ToWhomItMayConcern, PursuanttotheprovisionsoftheCommission’srulesTitle47Sections§0.457and§0.459,we arerequestingtheCommissiontowithholdthefollowingattachment(s)asconfidential documentsfrompublicdisclosureindefinitely. Thesedocumentscontaindetailedsystemandequipmentdescriptionsandareconsideredas proprietaryinformationinoperationoftheequipment.Thepublicdisclosureofthesedocuments mightbeharmfultoourcompanyandwouldgivecompetitorsanunfairadvantageinthemarket. SchematicDiagram BlockDiagram PartsList OperationalDescription Tune-upProcedure Inadditionaltoabovementioneddocuments,inordertocomplywiththemarketingregulations inTitle47CFR§2.803andtheimportationrulesinTitle47CFR§2.1204,whileensuringthat businesssensitiveinformationremainsconfidentialuntiltheactualmarketingofnewly authorizeddevices,werequestShortTermConfidentialityofthefollowingattachment(s); ExternalPhotos TestSetupPhotos InternalPhotos UserManual For45days,pursuanttoPublicNoticeDA04-1705. OR For180dayspursuanttoKDB726920D01. Itisourunderstandingthatallmeasurementtestreports,FCCIDlabelformatand correspondenceduringthecertificationreviewprocesscannotbegrantedasconfidential documentsandthisinformationwillbeavailableforpublicreviewoncethegrantofequipment authorizationisissued. Sincerely Stryd Contactperson:JamieWilliamson

Report No.: AGC01040221202AP03 Page 1 of 4 EXTERNAL PHOTOS WHOLE VIEW OF EUT TOP VIEW OF EUT Report No.: AGC01040221202AP03 Page 2 of 4 BOTTOM VIEW OF EUT FRONT VIEW OF EUT Report No.: AGC01040221202AP03 Page 3 of 4 BACK VIEW OF EUT LEFT VIEW OF EUT Report No.: AGC01040221202AP03 Page 4 of 4 RIGHT VIEW OF EUT ****************************************End of Report****************************************

FCC ID Label Location 3mm&10mm FCC ID: 2AJZH-PE932

RF EXPOSURE EVALUATION 1. PRODUCT INFORMATION Product Description Power Meter Model Name PE932 FCC ID 2AJZH-PE932 2. EVALUATION METHOD According to 447498 D01 General RF Exposure Guidance v06 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR. Where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation 3. CALCULATION BR/EDR: P t = -4.775dBm=0.33mW The value of the Maximum output power P t is referred to the test report of the CFR47 §15.247. The result for RF exposure evaluation SAR=(0.33mW /5mm) .[√2.402GHz)]=0.102<3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR. ANT+: P t =87.15dBuV/m(Average)@3m=-8.05dBm=0.16mW The value of the Maximum output power P t is referred to the test report of the CFR47 §15.249. The result for RF exposure evaluation SAR=(0.16mW / 5mm).[√2.457GHz)]=0.050<3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR. 4. CONCLUSION The SAR evaluation is not required.

Page 1 of 40 FCC Test Report Report No.: AGC01040221202FE02 FCC ID : 2AJZH-PE932 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Power Meter BRAND NAME : N/A MODEL NAME : PE932 APPLICANT : Stryd DATE OF ISSUE : Jan. 04, 2023 STANDARD(S) : FCC Part 15.247 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC01040221202FE02 Page 2 of 40 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jan. 04, 2023 Valid Initial Release Report No.: AGC01040221202FE02 Page 3 of 40 TABLE OF CONTENTS 1. VERIFICATION OF COMPLIANCE .................................................................................................................. 4 2. GENERAL INFORMATION .............................................................................................................................. 5 2.1. PRODUCT DESCRIPTION ........................................................................................................................ 5 2.2. TABLE OF CARRIER FREQUENCYS ....................................................................................................... 5 2.3. RELATED SUBMITTAL(S)/GRANT(S) ....................................................................................................... 6 2.4. TEST METHODOLOGY ............................................................................................................................. 6 2.5. SPECIAL ACCESSORIES .......................................................................................................................... 6 2.6. EQUIPMENT MODIFICATIONS ................................................................................................................. 6 2.7. ANTENNA REQUIREMENT ....................................................................................................................... 6 3. MEASUREMENT UNCERTAINTY ................................................................................................................... 7 4. DESCRIPTION OF TEST MODES ................................................................................................................... 8 5. SYSTEM TEST CONFIGURATION .................................................................................................................. 9 5.1. CONFIGURATION OF TESTED SYSTEM ................................................................................................. 9 5.2. EQUIPMENT USED IN TESTED SYSTEM ................................................................................................ 9 5.3. SUMMARY OF TEST RESULTS ................................................................................................................ 9 6. TEST FACILITY .............................................................................................................................................. 10 7. PEAK OUTPUT POWER ................................................................................................................................ 11 7.1. MEASUREMENT PROCEDURE .............................................................................................................. 11 7.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 11 7.3. LIMITS AND MEASUREMENT RESULT .................................................................................................. 12 8. BANDWIDTH .................................................................................................................................................. 14 8.1. MEASUREMENT PROCEDURE .............................................................................................................. 14 8.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 14 8.3. LIMITS AND MEASUREMENT RESULTS ............................................................................................... 14 9. CONDUCTED SPURIOUS EMISSION........................................................................................................... 18 9.1. MEASUREMENT PROCEDURE .............................................................................................................. 18 9.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 18 9.3. MEASUREMENT EQUIPMENT USED .................................................................................................... 18 9.4. LIMITS AND MEASUREMENT RESULT .................................................................................................. 18 10. MAXIMUM CONDUCTED OUTPUT POWER SPECTRAL DENSITY ........................................................ 25 10.1. MEASUREMENT PROCEDURE ............................................................................................................ 25 10.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................. 25 10.3. MEASUREMENT EQUIPMENT USED .................................................................................................. 25 10.4. LIMITS AND MEASUREMENT RESULT................................................................................................ 25 11. RADIATED EMISSION ................................................................................................................................. 27 11.1. MEASUREMENT PROCEDURE ............................................................................................................ 27 11.2. TEST SETUP .......................................................................................................................................... 28 11.3. LIMITS AND MEASUREMENT RESULT................................................................................................ 29 11.4. TEST RESULT .................................................…

Text truncated - open the document above for the full version.

Persisting in Technology antenna solutions for wireless technologies Prepared By: caichengwei Date of Report: 2023-1-3 NN01-110 Antenna Evaluating Report Auden Communications & Multimedia Techno (Kunshan) Co., Ltd Shenzhen branch 1 Company Confidential, Auden Many aspects of this presentation are protected by US, TW, CN and international patents and patent applications Report History DateRevDescription 2023-1-301 Test BT&Ant+ Efficiency and Gain 2 Company Confidential, Auden Many aspects of this presentation are protected by US, TW, CN and international patents and patent applications Equipment 3 lChamber：GTS Rayzone1800 lNetwork analyzer：Agilent E5071C l2G/3G comprehensive tester：Agilent 8960 lLTE comprehensive tester：Anritsu MT8820 lTD comprehensive tester：StarPoint SP6010 lWIFI comprehensive tester：Anritsu MT8860 lGPS Signal Source：Agilent E4438C Company Confidential, Auden Many aspects of this presentation are protected by US, TW, CN and international patents and patent applications Fixture Environment 4 Frequency Range Using System Band Using System Band GSM-WIFI / BT2.4G(2400-2500MHz) WCDMA-GPS- TD-SCDMA-FM- CDMA-Others- FDD LTE TDD LTE Company Confidential, Auden Many aspects of this presentation are protected by US, TW, CN and international patents and patent applications Antenna information lP/N： NN01-110 Antenna Type:Glass Epoxy Chip Antenna lManufacturer： Ignion Micro Reach XtendTM lBrand:ignion lDimension（Unit : mm）： 5 Company Confidential, Auden Many aspects of this presentation are protected by US, TW, CN and international patents and patent applications BT&Ant+ Test Effic & Gain Frequency(MHz) Eff.(%)Gain(dBi) 24007.79-4.66 24108.63-4.37 24209.33-4.12 243010.88-3.55 244012.51-3.11 245013.64-2.57 246015.86-1.65 247017.14-1.06 248016.73-0.89 249016.79-0.63 250015.75-0.69 6 Company Confidential, Auden Many aspects of this presentation are protected by US, TW, CN and international patents and patent applications BT&Ant+ Test E1 Plant 7 Company Confidential, Auden Many aspects of this presentation are protected by US, TW, CN and international patents and patent applications BT&Ant+ Test E2 Plant 8 Company Confidential, Auden Many aspects of this presentation are protected by US, TW, CN and international patents and patent applications BT&Ant+ Test H plant 9 Company Confidential, Auden Many aspects of this presentation are protected by US, TW, CN and international patents and patent applications BT&Ant+ Test 3D Radiation 10 Company Confidential, Auden Many aspects of this presentation are protected by US, TW, CN and international patents and patent applications Thank You AUDEN UPGRADE DEVOTE EXCELLENCE NAVIGATOR AUDEN Techno Corp. Taiwan TEL: +886-3-363-1901 No.19 Lane 772, Ho Ping Road Bade City, Taoyuan Hsien, Taiwan. AUDEN communications & Multimedia Techno (Shenzhen) Co., Ltd. TEL: +86 0755 8653 9953 AUDEN Techno Corp. Korea TEL: +82 2 401 1206 RM 205 5F Jaeil Officetel Songpa daero Songpa-Gu Seoul. ZIP : 138-719 Korea AUDEN Techno Corp. USA TEL：+1 631 9791630 4 Cygnet Drive Smittown, NY 11787 E-mail: [email protected] Website: http://www.auden.com.tw 11

Report No.: AGC01040221202AP02 Page 1 of 2 TEST SETUP PHOTOS RADIATED EMISSION TEST SETUP BELOW 1GHz RADIATED EMISSION TEST SETUP ABOVE 1GHz Report No.: AGC01040221202AP02 Page 2 of 2 RF CONDUCTED TEST SETUP (BT) RF CONDUCTED TEST SETUP (ANT+) ****************************************End of Report*************************************