2AK4IMLT-EXAG-KHEXAGON BT Controller

HEXAGON BT Controller Specification FEATURE Compatible with PS4,PS3 and PC D-input and Android( above 6.0) Can play PS4 games on PS5 Console With audio output With Motion sensor With Vibration-(Cell Motor) Without turbo Function Built-in 600mAh /900mAh /1200mAh Li-ion battery Including Home, Share, Options, D-pad, Circle,Triangle,Square,Cross, L1, R1,L2 , R2 ,2 Joysticks, 2 Triggers and reset button With upgradable firmware by USB With Mapped X-Y Touch pad and Click Button Interchangeable custom shapes for D-pad and Analogue Stick built-in magnets The front LED bar is white color only 80cm Type C charging cable Support the game sound and voice chat Multi setup RGB LED Light Image The 3.5mm Jack Audio Output Support the game sound and voice chat Sleep mode The controller enters into Sleep mode if fail to connect with PS4 console after 30 seconds searching mode or no buttons are active for 10 minutes or no obvious movement of 3D analog for 10 minutes. By pressing Home button to wake up the controller again LED Indication When controller is connected to the console, the LED is white Stand-by mode: white LED is on Charge while playing : white Led is in breathing mode Charge while in stand-by mode: white LED is in breathing mode, and light goes off when fully charged Controller disconnection: white LED is off The white Led indicators will enter into breathing light mode if the controller is charging under power off status; The LED light goes off when controller is fully charged. Bluetooth Connection: 1) PS3/PS4/PS5 Console When connecting with PS3/PS4/PS5 console for the first time, one Type C data cable is required to connect the controller to the console. For subsequent use, only need to press HOME button one time, the white LED will blinking slowly, the connection is successful when the white LED stop blinking 2)When connecting with PC, open the bluetooth on the PC, click to add new BT device, then keep pressing HOME+ SHARE until you see the “wireless controller” device name, click to connect with the controller. The white LED is blinking during connection. When the LED stop blinking, the wireless connection is successful 3)When connecting with Android system, open the bluetooth on smartphone , then keep pressing HOME+ SHARE of gamepad until you see the “Wireless Controller” device name on the bluetooth device list, click to connect with the gamepad. The white LED is blinking slowly during connection. When the LED stop blinking, the wireless connection is successful For subsequent use, only need to press HOME button one time, the white LED will blinking slowly, the connection is successful when the white LED stop blinking Available games: Games under Android standard protocol and downloaded games from http://www.putaogame.com/ PS: Keep the gamepad powered off during connecting with Android system Without vibration and motion sensor on games downloaded from http://www.putaogame.com/ Wired Connection: Also can connect to the PS4, PS3 console and PC by cable On PC platform, you can switch the PC mode from X-input to D-input by pressing HOME button 5 times Multi setup RGB Light: 1:How to Switch on the RGB Light? Pressing L1 and R1 for 5 seconds 2:How to Switch off the RGB Light? Pressing L1 and R1 for 5 seconds 3:How many light modes? The lights modes are mainly divided into four groups of light display modes: a)Fixed color mode including 8 colors that’s white-red-orange-yellow-green-cyan-blue-purple. By pressing the Home + Triangle buttons to enter this LED light mode and change the colors among 8 colors b)Fixed color breathing mode including 8 colors that’s white-red-orange-yellow-green-cyan-blue-purple. By pressing the Home + Square buttons to enter this LED light mode and change the breathing colors among 8 colors c)Colorful gradient mode . By pressing the Home + cross buttons to enter this LED light mode d)Rainbow running light mode.By pressing the Home + circle buttons to enter this LED light mode 4: When turn on the controller, the default RGB is mode d Correspondence of Standard PS4 and PC buttons (Chart). PS4□ ×O △ L1 R1 L2 R2 SHARE OPTION L3 R3PST-PAD PC-D-input12345 6 7 891011 121314 Trouble Shooting 1.If the connection between the controller and the wheel is failed, please re-connect the original controller again and retry 2.If the wheel does not work, turn off and turn on again the console and follow the GUIDE procedure again Cautions 1.Please carefully read this instruction manual before using this racing wheel 2.Do not hit or drop it 3.Do not disassemble, modify, or try to repair the wheel by yourself or in any non-authorized service center 4.Do not store the wheel into a humid, hot, or greasy place NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio fre quency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

MTM Industrial Ltd. No. 98, Dingwan 4th Road, Sanzao Town, Jinwan District , Zhu Hai, Guang Dong Province, China Date: 2023-05-19 Product Model Number: MLT-EXAG-K FCC ID: 2AK4IMLT-EXAG-K To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following:  Testing  Approval applications and procedures We declare that ORGANIZATION. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by ORGANIZATION. on our behalf shall have the same effect as acts of our own. By: susan zhang Contact Listed on FCC Wesbite Title: Manager Email: [email protected] Telephone: 0756-6989310 On behalf of: MTM Industrial Ltd.

MTMIndustrialLtd. No.98,Dingwan4thRoad,SanzaoTown,JinwanDistrict,ZhuHai,GuangDongProvince,China FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 USA Date:04-06-2023 Ref:AttestationStatementsPart2.911(d)(5)(i)Filing FCCID:2AK4IMLT-EXAG-K [MTMIndustrialLtd.](“theapplicant”)certifiesthattheequipmentforwhichauthorizationissoughtis not“covered”equipmentprohibitedfromreceivinganequipmentauthorizationpursuanttosection 2.903oftheFCCrules. Sincerely, (Applicantsignature) MTMIndustrialLtd. No.98,Dingwan4thRoad,SanzaoTown,JinwanDistrict,ZhuHai,GuangDongProvince,China FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 USA Date:04-06-2023 Ref:AttestationStatementsPart2.911(d)(5)(ii)Filing FCCID:2AK4IMLT-EXAG-K [MTMIndustrialLtd.](“theapplicant”)certifiesthat,asofthedateofthefilingoftheapplication,the applicantisnotidentifiedontheCoveredListasanentityproducing“covered”equipment. Sincerely, (Applicantsignature)

MTMIndustrialLtd. No.98,Dingwan4thRoad,SanzaoTown,JinwanDistrict,ZhuHai,GuangDongProvince,China OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USA Date:2023-04-06 Subject;RequestforConfidentiality FCCID:2AK4IMLT-EXAG-K ToWhomItMayConcern, PursuanttotheprovisionsoftheCommission’srulesTitle47Sections§0.457and§0.459,we arerequestingtheCommissiontowithholdthefollowingattachment(s)asconfidential documentsfrompublicdisclosureindefinitely. Thesedocumentscontaindetailedsystemandequipmentdescriptionsandareconsideredas proprietaryinformationinoperationoftheequipment.Thepublicdisclosureofthesedocuments mightbeharmfultoourcompanyandwouldgivecompetitorsanunfairadvantageinthemarket. SchematicDiagram BlockDiagram PartsList OperationalDescription Tune-upProcedure Inadditionaltoabovementioneddocuments,inordertocomplywiththemarketingregulations inTitle47CFR§2.803andtheimportationrulesinTitle47CFR§2.1204,whileensuringthat businesssensitiveinformationremainsconfidentialuntiltheactualmarketingofnewly authorizeddevices,werequestShortTermConfidentialityofthefollowingattachment(s); ExternalPhotos TestSetupPhotos InternalPhotos UserManual For45days,pursuanttoPublicNoticeDA04-1705. OR For180dayspursuanttoKDB726920D01. Itisourunderstandingthatallmeasurementtestreports,FCCIDlabelformatand correspondenceduringthecertificationreviewprocesscannotbegrantedasconfidential documentsandthisinformationwillbeavailableforpublicreviewoncethegrantofequipment authorizationisissued. Sincerely Contactperson:

2018/09/25 SHENZHEN ALANTE TECHNOLOGY CO LTD 113 Antenna specification 2018/09/25 SHENZHEN ALANTE TECHNOLOGY CO LTD 213 1.Dimensions 2.Specifications number Item Specifications 1 Working Central Frequency 2441 MHz 2 Band Width (2402-2480)MHz 3 Gain 1.59 dBi 4 VSWR ≤2.0 5 Antenna type PCB antenna 6 Azimuth Beam width Omni‐directional 7 Impedance 50欧姆 8 Modulation mode GFSK Frequency (MHz) Efficiency (%) Gain (dBi) 2397MHz 20.196 1.47dBi 2450MHz 10.157 1.51 dBi 2482 MHz 21.942 1.59 dBi 2018/09/25 SHENZHEN ALANTE TECHNOLOGY CO LTD 313 3. Instrument testing, software simulation parameters ① VSWR Mkr1: 2397MHz 1.47 Mkr2: 2450MHz 1.51 Mkr3: 2482 MHz 1.59 2018/09/25 SHENZHEN ALANTE TECHNOLOGY CO LTD 413 ②Smith Char Mkr1: 2397MHz 73.4 Mkr2: 2450MHz 62.7 Mkr3: 2482MHz 66.8 2018/09/25 SHENZHEN ALANTE TECHNOLOGY CO LTD 513 ③Return Loss Mkr1: 2397MHz -15 Mkr2: 2450MHz -18 Mkr3: 2482 MHz -16 2018/09/25 SHENZHEN ALANTE TECHNOLOGY CO LTD 613 ④Smith Char The simulation Mkr1: 2400MHz 1.234 Mkr2: 2500MHz 1.051 Mkr3: 2600MHz 1.322 2018/09/25 SHENZHEN ALANTE TECHNOLOGY CO LTD 713 ⑤Return Loss The simulation Mkr1: 2400MHz -19.59 Mkr2: 2450MHz -27.70 Mkr3: 2500MHz -31.97 Mkr4: 2550MHz -21.83 2018/09/25 SHENZHEN ALANTE TECHNOLOGY CO LTD 813 ⑥Phase The simulation Mkr1: 2400MHz -54.89 Mkr2: 2500MHz -82.03 Mkr3: 2600MHz -102.6 2018/09/25 SHENZHEN ALANTE TECHNOLOGY CO LTD 913 4. Radiation Pattems XY-plane 2018/09/25 SHENZHEN ALANTE TECHNOLOGY CO LTD 1013 XZ-plane 2018/09/25 SHENZHEN ALANTE TECHNOLOGY CO LTD 1113 YZ-plane 2018/09/25 SHENZHEN ALANTE TECHNOLOGY CO LTD 1213 3D Radiation field type 2018/09/25 SHENZHEN ALANTE TECHNOLOGY CO LTD 1313

Report No.: AGC08184230301AP03 Page 1 of 3 EXTERNAL PHOTOS TOP VIEW OF EUT BOTTOM VIEW OF EUT Report No.: AGC08184230301AP03 Page 2 of 3 FRONT VIEW OF EUT BACK VIEW OF EUT Report No.: AGC08184230301AP03 Page 3 of 3 LEFT VIEW OF EUT RIGHT VIEW OF EUT ****************************************End of Report*************************************

FCC ID Label Location 40mm&20mm FCC ID: 2AK4IMLT-EXAG-K

Report No.: AGC08184230301AP03 Page 1 of 4 INTERNAL PHOTOS OPEN VIEW OF EUT (FIGURE 1) BATTERY VIEW OF EUT (FIGURE 1) Report No.: AGC08184230301AP03 Page 2 of 4 ANTENNA CLOSE-UP PHOTO-1 INTERNAL VIEW OF EUT (FIGURE 1) BT Antenna Report No.: AGC08184230301AP03 Page 3 of 4 INTERNAL VIEW OF EUT (FIGURE 2) INTERNAL VIEW OF EUT (FIGURE 3) Report No.: AGC08184230301AP03 Page 4 of 4 INTERNAL VIEW OF EUT (FIGURE 4) INTERNAL VIEW OF EUT (FIGURE 5) ****************************************End of Report*************************************

RF EXPOSURE EVALUATION 1. PRODUCT INFORMATION FCC ID 2AK4IMLT-EXAG-K Product Description HEXAGON BT Controller Model Name MLT-EXAG-K Frequency Band (Operating) WLAN: 2.412GHz ~ 2.462GHz WLAN: 5.18GHz ~ 5.32GHz / 5.50GHz ~ 5.70GHz WLAN: 5.745GHz ~ 5825GHz Bluetooth: 2.402GHz ~ 2.480GHz Others (NFC:13.56MHz) Device Category Portable (<20cm separation) Mobile (>20cm separation) Others: Antenna Diversity Single antenna Multiple antennas Max. Output Power BR EDR: -0.676dBm (Max) BLE 1M: -1.855dBm (Max) BLE 2M: -1.857dBm (Max) Antenna Designation PCB Antenna Antenna Gain 1.59dBi Minimum Assessment Distance 5mm Evaluation Applied MPE Evaluation SAR Evaluation Evaluation Result Pass 2. PORTABLE DEVICE EVALUATION METHOD AND LIMIT Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] [if(GHz)] s 3.0 for 1-g SAR and ñ 7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz.  Power and distance are rounded to the nearest mW and mm before calculation.  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance - 50mm) ( f(MHz)/150)] mW, at 100MHz to 1500 MHz; b) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)-10] mW at > 1500 MHz and ≤6 GHz; 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by 1/2 for test separation distances ñ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. 3. MOBILE DEVICE EVALUATION METHOD AND LIMIT Human exposure to RF emissions from mobile devices (47 CFR §2.1091) may be evaluated based on the MPE limits adopted by the FCC for electric and magnetic field strength and/or power density, as appropriate, since exposures are assumed to occur at distances of 20 cm or more from persons. LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE Frequency Range (MHz) E-field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Time |E| 2 , |H| 2 or S (Minutes) 0.3 -- 1.34 614 1.63 (100)* 30 1.34 -- 30 824/f 2.19/f (180/f 2 )* 30 30 -- 300 27.5 0.073 0.2 30 300 -- 1500 -- -- f/1500 30 1500 -- 100,000 -- -- 1.0 30 *Note: 1. f= Frequency in MHz * Plane-wave Equivalent Power Density 2. The averaging time for General Population/Uncontrolled exposure to fixed transmitters is not applicable for mobile and portable transmitters. See 47 CFR §§2.1091 and 2.1093 on source-based time-averaging requirement for mobile and portable transmitters. S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna 4. MEASUREMENT RESULT Test Mode Channel Frequency (MHz) Max Output power (dBm) Max Output power (mW) Calculati on Value (Note 1) Threshold Value GFSK 1Mbps BT_BLE 2402 -1.855 0.652 0.202 3.0 BT_BLE 2440 -2.005 0.630 0.197 3.0 BT_BLE 2480 -2.461 0.567 0.178 3.0 GFSK 2Mbps BT_BLE 2402 -1.857 0.652 0.202 3.0 BT_BLE 2440 -1.946 0.639 0.199 3.0 BT_BLE 2480 -2.397 0.576 0.181 3.0 8DPSK BT_EDR 2402 -0.676 0.856 0.265 3.0 BT_EDR 2441 -0.782 0.835 0.261 3.0 BT_EDR 2480 -1.235 0.752 0.236 3.0 Note 1: Calculation Value =[(max. power of channel, mW)/(min. test separation distance, mm)] ·[√f(GHz)]. Fox example: 0.856/5*√2.402=0.265 ≤ 3.0 According to KDB447498 D01 V06, threshold at which no SAR required is ≤3.0 for 1-g SAR, separation distance is 5mm, and no simultaneous SAR measurement is required. 5. CONCLUSION Since Source-base time average power is below SAR test exclusion power thresholds, the SAR evaluation is not required.

Page 1 of 60 FCC Test Report Report No.: AGC08184230301FE02 FCC ID : 2AK4IMLT-EXAG-K APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : HEXAGON BT Controller BRAND NAME : NITHO MODEL NAME : MLT-EXAG-K APPLICANT : MTM Industrial Ltd. DATE OF ISSUE : Apr. 03, 2023 STANDARD(S) : FCC Part 15.247 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC08184230301FE02 Page 2 of 60 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Apr. 03, 2023 Valid Initial Release Report No.: AGC08184230301FE02 Page 3 of 60 TABLE OF CONTENTS 1. VERIFICATION OF COMPLIANCE .................................................................................................................. 5 2. GENERAL INFORMATION .............................................................................................................................. 6 2.1. PRODUCT DESCRIPTION ........................................................................................................................ 6 2.2. TABLE OF CARRIER FREQUENCYS ....................................................................................................... 6 2.3. RELATED SUBMITTAL(S)/GRANT(S) ....................................................................................................... 7 2.4. TEST METHODOLOGY ............................................................................................................................. 7 2.5. SPECIAL ACCESSORIES .......................................................................................................................... 7 2.6. EQUIPMENT MODIFICATIONS ................................................................................................................. 7 2.7. ANTENNA REQUIREMENT ....................................................................................................................... 7 3. MEASUREMENT UNCERTAINTY ................................................................................................................... 8 4. DESCRIPTION OF TEST MODES ................................................................................................................... 9 5. SYSTEM TEST CONFIGURATION ................................................................................................................ 10 5.1. CONFIGURATION OF TESTED SYSTEM ............................................................................................... 10 5.2. EQUIPMENT USED IN TESTED SYSTEM .............................................................................................. 10 5.3. SUMMARY OF TEST RESULTS .............................................................................................................. 10 6. TEST FACILITY .............................................................................................................................................. 11 7. PEAK OUTPUT POWER ................................................................................................................................ 12 7.1. MEASUREMENT PROCEDURE .............................................................................................................. 12 7.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 12 7.3. LIMITS AND MEASUREMENT RESULT .................................................................................................. 13 8. BANDWIDTH .................................................................................................................................................. 17 8.1. MEASUREMENT PROCEDURE .............................................................................................................. 17 8.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 17 8.3. LIMITS AND MEASUREMENT RESULTS ............................................................................................... 17 9. CONDUCTED SPURIOUS EMISSION........................................................................................................... 24 9.1. MEASUREMENT PROCEDURE .............................................................................................................. 24 9.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 24 9.3. MEASUREMENT EQUIPMENT USED .................................................................................................... 24 9.4. LIMITS AND MEASUREMENT RESULT .................................................................................................. 24 10. MAXIMUM CONDUCTED OUTPUT POWER SPECTRAL DENSITY ........................................................ 36 Report No.: AGC08184230301FE02 Page 4 of 60 10.1. MEASUREMENT PROCEDURE ............................................................................................................ 36 10.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................. 36 10.3. MEASUREMENT EQUIPMENT USED .................................................................................................. 36 10.4. LIMITS AND MEASUREMENT RESULT................................................................................................ 36 11. RADIATED EMISSION ................................................................................................................................. 40 11.1. MEASUREMENT PROCEDURE ............................................................................................................ 40 11.2. TEST SETUP .......................................................................................................................................... 41 11.3. LIMITS AND MEASUREMENT RESULT............................................................................................…

Text truncated - open the document above for the full version.

Report No.: AGC08184230301AP02 Page 1 of 2 TEST SETUP PHOTOS RADIATED EMISSION TEST SETUP BELOW 1GHz RADIATED EMISSION TEST SETUP ABOVE 1GHz Report No.: AGC08184230301AP02 Page 2 of 2 AC POWER LINE CONDUCTED TEST SETUP RF CONDUCTED TEST SETUP ****************************************End of Report*************************************