2AKPQNDLM007PE Smart Lighting Hybrid Node

Smart Lighting Node Hybrid NEMA MinebeaMitsumi Inc. 3-9-6 Mita, Minato-ku, Tokyo 108-8330 • Phone: +81-03-6758-6711 • www.minebeamitsumi.com Before the installation Before the installation, the installer/user must read the full manual available at the following internet address upon registration at Paradox Engineering website: Warnings (English) The following instructions provide important precautions to safely install, use and maintain the product. Please read and follow them carefully before operating the unit: failure to comply may compromise people safety and/or damage the device, with serious consequences depending on circumstances. • The equipment is Class II equipment and fits outdoor installation. It does not require (and must not have) a safety connection to electrical earth. • The equipment is intended for installation, service and repair by trained and skilled personnel only (no operator access) • Install the product in accordance with the instructions provided in this installation manual • The manufacturer shall not be held liable for errors or damages due to wrong mounting operations • This equipment is intended to be used with elevations up to 2000 m • The product and the various units comprising the installation must only be used for the purpose for which they are intended. Any other use is considered improper and dangerous • Unpack the product and check possible damages before installing and operating it • Electrical work and installation must be performed in accordance with relevant local and national regulations, following the instructions provided in this installation manual. • Before connecting the product, make sure that product voltage ratings correspond to the mains power supply voltage • Product drivers are default set as per the configuration sheet provided with the product. The product must only be installed in luminaires with compatible drivers. • When plugging the product on the luminaire socket, ensure that the North indicator on the cap is aligned with the North indicator of the luminaire socket. • Install the product under a good GPS coverage. • Before cleaning or servicing the product, disconnect it from the mains power • Dispose of packaging or product must be in compliance with applicable local and national waste disposal regulation • Keep this document for future use and reference Warnings (Français) • L'équipement est un équipement de classe II et convient à une installation en extérieur. Il ne nécessite pas (et ne doit pas avoir) de connexion de sécurité à la terre électrique • Ces équipements sont destinés à l’installation, l’entretien et la réparation effectués uniquement par un personnel formé et qualifié (aucun accès à l’opérateur) • Installer le produit selon les instructions fournies dans ce manuel d’installation • Le fabricant n’est pas responsable d’erreurs ou de dommages attribuables à des opérations de montage erronées • Ces équipements sont destinés à être utilisés jusqu’à 2.000 mètres d’altitude • Le produit et les différentes unités comprenant l’installation doivent être utilisés seulement pour les finalités pour lesquelles ils sont prévus. Toute autre utilisation est considérée comme inappropriée et dangereuse • Déballer le produit et contrôler les dommages possibles avant de l’installer et de le faire fonctionner • L’installation et le travail électrique doivent être effectués conformément aux réglementations nationales et locales pertinentes en suivant les instructions fournies dans ce manuel d’installation. • Avant de brancher le produit, s’assurer que la tension nominale du produit corresponde à la tension d’alimentation du réseau électrique • Les drivers de produits sont définis par défaut conformément à la feuille de configuration fournie avec le produit. Le produit ne doit être installé que dans des luminaires avec des drivers compatibles. • Lorsque vous branchez le produit sur la prise du luminaire, assurez- vous que l'indicateur Nord sur le capuchon est aligné avec l'indicateur Nord de la prise du luminaire. • Installez le produit sous une bonne couverture GPS • Avant de nettoyer ou d’assurer l’entretien du produit, il faut le débrancher du réseau électrique • L’élimination du produit ou de son emballage doit être conforme aux réglementations nationales et locales pertinentes en matière d’élimination des déchets • Conserver ce document pour une utilisation et des besoins futurs USA RF exposure information The NDLM007US (FCC ID: 2AKPQNDLM007) complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept all interference received, including interference that may cause undesired operation This device should be operated with a minimum separation distance of 50 cm between the equipment and a person’s body. The calculations were carried out assuming no co-location or operation in conjunction with any other antenna or device which may contain transmitters. The equipment contains: NDLM007US-1, FCC ID: N7NWP77B NDLM007US-2, FCC ID: N7NWP76B RF exposure guidelines for addressing co-location The device should not be co-located with any other transmitter during the installation without following the FCC co-location procedure first (FCC KDB 447498 RF exposure guidelines for addressing co-location). US Responsible party NMB Technologies Corporation, 9730 Independence Ave, Chatsworth, CA 91311, United States Changes Changes or modifications made to this equipment not expressly approved by MinebeaMitsumi inc., may void the user’s authority to operate this equipment. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance…

Text truncated - open the document above for the full version.

Paradox Engineering SA Via Passeggiata 7, Novazzano, Switzerland • Phone: +41 91 233 0100 • [email protected]• www.pdxeng.ch NEMA Hybrid (NEMA) – FCC ID: 2AKPQNDLM007US Label position

DEG < = ±0.5 ±0.8 ±0.5 ±0.3 ±0.2 ±0.1 4＜Ｌ 16 250＜Ｌ 1000 63＜Ｌ 250 16＜Ｌ 63 Ｌ 4 公差寸法 Ｌ 一 般 公 差 = < = < = < = < TOL 角度 10.5 10.5 2 2 7 min. DATA MATRIX -1-2 A 2 製造管理番号 / Serial No. EX.) X YY MM DD XXXX 0001 ～ 9999 (4 digit) Day : 01 ～ 09, 10 - - - - Month : 01 ～ 09, 10, 11, 12 2022 A.D. Product rev. (Product rev. should be followed the Innovator) 2 注記 / Notes 1. ラベル材質 / Label material 詳細はUD6PA-E0003298*を参照のこと / Refer to Blank label dwg UD6PA-E0003298* 2. ラべリングシステム / Marking and labeling system メーカー / Maker : LINTEC CORP. (UL File No. MH18338) 3. 文字色 / Character color : 黒 / Black 4. 文字は鮮明で読み取る事ができること / Letter must be clear and legible. 5. 使用インク / Ink 使用するインクの型番はBOMを参照すること / Refer to Bom for the ink. 6. ミネベアミツミグループグリーン調達管理要領 EM10507の使用禁止物質・制限物質の規定に準拠すること。 Products shall comply with the provisions of banned substance and restricted substance in MinebeaMitsumi group green procurement standard EM10507. 製品番号 / MinebeaMitsumi P/No. Should be followed the below matrix and Innovator. Should be followed the below matrix and Innovator. 製品番号 / MinebeaMitsumi P/No. 1 1 (The definition of serial number to be started from 0001 everyday) EX). 84:84:33:01:02:AA:BB:CC (23 digit) MAC address (Automatic assignment) 3 EX). f8dc7a1e32e5 (12 digit) MAC BT (Automatic assignment) 4 EX). 3536341101100450 (16 digit) IMEI (Automatic assignment) 5 EX). 89332500000007042985 (20 digit) ICCID (Automatic assignment) 6 1 4 3 5 6 製品名/Product nameDestinationName of country GWWG001 KH(Cambodia) TH(Thailand) EU(Europe) US(USA) 製品名/Product name LTE Module NDLM007US WP7702 -1 WP7611-1 -2 B C D A 321456 1/3 mm 1.5:1 PRODUCT LABEL NDLM007US -UF3PA-E0000920 符号 MARKDATE 日付変更理由 REASON ECN No. 作図 DRAWN 調査 CHECKED 調査 CHECKED 承認 APPROVED ミネベアミツミ株式会社 MinebeaMitsumi Inc. DRAWNCHECKEDCHECKEDAPPROVED UNIT 単位 SCALE 尺度 材質 MATERIAL 表面粗サ SURF. ROUGH 熱処理 HEAT TREAT 表面処理 FINISH REV. 改訂 SHEET 葉番 DATE 作成日 DESCRIPTION 品名 PART No.(MODEL No.) 品番 DRAWING No. 図番 FILE NAME MinebeaMitsumi confidential Manufacturer,Material name UF3PA-E0000920_0 (PRODUCT LABEL_NDLM007US) 14 - JUN - '22 0 K.Nonoyama Y.Sakai M.Yamashita S.Kamimura M.Matsushima A K.NonoyamaO.Shigehata S.Kamimura R.Mashio M.Yamashita Change label layout & Data matrix content Add OP(②) content 14.APR.'22 DEG < = ±0.5 ±0.8 ±0.5 ±0.3 ±0.2 ±0.1 4＜Ｌ 16 250＜Ｌ 1000 63＜Ｌ 250 16＜Ｌ 63 Ｌ 4 公差寸法 Ｌ 一 般 公 差 = < = < = < = < TOL 角度 H : ICCID (LTE Modem) (20 digit) EX.) 89332500000007042985 G : IMEI (16 digit) EX.) 3536341101100450 F : MAC BT (Bluetooth Mac address) (12 digit) EX.) f8dc7a1e32e5 G F B EX.) 84:84:33:01:02:AA:BB:CC$YYMMDD0001$NDLM007USXX$f8dc7a1e32e5$3536341101100450$89332500000007042985 D A DATA MATRIX DETAIL(Total 97 digit) B C B 3 A : Mac address (23 digit) EX.) 84:84:33:01:02:AA:BB:CC B : $ mark (1 digit) " $ " C : Year & Month & Day (6 digit) EX.) 220101 Day : 01 ～ 09, 10 - - - - Month : 01 ～ 09, 10, 11, 12 2022 A.D. E : MODEL No. (11 digit) EX.) NDLM007USXX D : Serial number (4 digit) The definition of serial number to be started from 0001 everyday. EX.) 0001 0001～9999 H B E B B C D A 321456 2/3 mm 3:1 PRODUCT LABEL NDLM007US -UF3PA-E0000920 符号 MARKDATE 日付変更理由 REASON ECN No. 作図 DRAWN 調査 CHECKED 調査 CHECKED 承認 APPROVED ミネベアミツミ株式会社 MinebeaMitsumi Inc. DRAWNCHECKEDCHECKEDAPPROVED UNIT 単位 SCALE 尺度 材質 MATERIAL 表面粗サ SURF. ROUGH 熱処理 HEAT TREAT 表面処理 FINISH REV. 改訂 SHEET 葉番 DATE 作成日 DESCRIPTION 品名 PART No.(MODEL No.) 品番 DRAWING No. 図番 FILE NAME MinebeaMitsumi confidential Manufacturer,Material name UF3PA-E0000920_0 (PRODUCT LABEL_NDLM007US) 14 - JUN - '22 0 None DEG < = ±0.5 ±0.8 ±0.5 ±0.3 ±0.2 ±0.1 4＜Ｌ 16 250＜Ｌ 1000 63＜Ｌ 250 16＜Ｌ 63 Ｌ 4 公差寸法 Ｌ 一 般 公 差 = < = < = < = < TOL 角度 -1-2 AFTER PRINTED B C D A 321456 3/3 mm 3:1 PRODUCT LABEL NDLM007US -UF3PA-E0000920 符号 MARKDATE 日付変更理由 REASON ECN No. 作図 DRAWN 調査 CHECKED 調査 CHECKED 承認 APPROVED ミネベアミツミ株式会社 MinebeaMitsumi Inc. DRAWNCHECKEDCHECKEDAPPROVED UNIT 単位 SCALE 尺度 材質 MATERIAL 表面粗サ SURF. ROUGH 熱処理 HEAT TREAT 表面処理 FINISH REV. 改訂 SHEET 葉番 DATE 作成日 DESCRIPTION 品名 PART No.(MODEL No.) 品番 DRAWING No. 図番 FILE NAME MinebeaMitsumi confidential Manufacturer,Material name UF3PA-E0000920_0 (PRODUCT LABEL_NDLM007US) 14 - JUN - '22 0 None

Paradox Engineering SA Via Passeggiata 7, Novazzano, Switzerland • Phone: +41 91 233 0100 • [email protected]• www.pdxeng.ch NDLM007US-1 NDLM007US-2 NEMA Hybrid (NEMA) – FCC ID: 2AKPQNDLM007US Internal pictures 2 3GPP board 3 Connector board 4 Power board 5 Signal board 6 Narrowband 915 MHz, Paradox Engineering 7 LTE Module Cat-M1, Sierra Wireless, WP7702, FCC ID: N7NWP77B for NDLM007US-1 8 LTE Module Cat-1, Sierra Wireless, WP77611-1, FCC ID: N7NWP76B for NDLM007US-2

PRS LAB S.r.l. Unipersonale Sede operativa e Laboratori di prova Headquarter and Testing lab Via Campagna, 92 I 22020 Faloppio (CO) I Italy Tel. +39 031 3500011 I Fax +39 031 991309 [email protected] I www.primaricerca.it Mod 18_48 rev05 Test Report FCCTR Rapporto di prova - Test report n. FCCTR_181512-1 I Data - Date 28/09/2022 Pagina 1 di 61 RAPPORTO DI PROVA TEST REPORT Rif. / Ref. n. FCCTR_181512-1 Data Emissione /Issue Date: 28/09/2022 Pagine / Pages: 61 Scopo delle prove Test object Prove di tipo in accordo alla Norme Type test according to Standards 47 CFR FCC part 15 - Subpart C - §15.247 Richiedente Applicant Paradox Engineering SA Via Passeggiata 7 – 6883 Novazzano – CH Tel.: +41912330100 Marchio commerciale Trade mark Fabbricante Manufacturer MinabeaMitsumi Inc. 3-9-6 Mita, Minato-ku, Tokyo 108-8330 Tel.: 81-3-6758-6711 Prodotto Product Sub 1-GHz IPv6/6LoWPAN Hardware radio device, compliant within NEMA standard, that operates as: Smart Lighting Node and Gateway for other Nodes Modello Model NDLM007US-1 Identificativo FCC FCC ID 2AKPQNDLM007 Data ricevimento campioni Date of test samples receipt 09/05/2022 Campioni verificati No. of tested samples 1 – Sampled by the applicant Data verifiche Testing date From 26/05/2022 to 08/06/2022 Sito di prova Testing site PRSLAB S.r.l. Unipersonale - Via Campagna 92 - 22020 Faloppio - Como - Italy Identificativo FCC del sito di prova FCC designation number IT0012 Esito delle valutazioni Assessment results CONFORME / COMPLIANT Verifiche effettuate da Verifications carried out by Daniele AOSANI Tecnico Laboratorio Laboratory Engineer Approvato Approved by Riccardo PFEIFFER Responsabile Laboratorio Laboratory Manager I risultati delle prove riportati nel presente rapporto di prova si riferiscono solo ai campioni esaminati. The test results reported in this test report shall refer only to the samples tested. Il campione è stato fornito dal cliente ed i risultati si riferiscono al campione così come ricevuto The sample has been provided by the customer and the results apply to the sample as received Questo Report non può essere riprodotto in modo parziale, salvo espressa autorizzazione scritta da parte del Laboratorio This report may not be partially reproduced, except with the prior written permission of the issuing Laboratory PRS LAB S.r.l. Unipersonale Sede operativa e Laboratori di prova Headquarter and Testing lab Via Campagna, 92 I 22020 Faloppio (CO) I Italy Tel. +39 031 3500011 I Fax +39 031 991309 [email protected] I www.primaricerca.it Mod 18_48 rev05 Test Report FCCTR Rapporto di prova - Test report n. FCCTR_181512-1 I Data - Date 28/09/2022 Pagina 2 di 61 CONTENUTO TABLE OF CONTENTS 0. RELEASE CONTROL RECORD .............................................................................................. 3 1. DECISION RULE ................................................................................................................. 3 2. INFORMATION PROVIDED BY CUSTOMER .......................................................................... 4 3. GENERAL REMARKS .......................................................................................................... 4 4. TECHNICAL INFORMATION OF EQUIPMENT UNDER TEST (EUT) .......................................... 5 4.1 EUT Identification .................................................................................................................. 5 4.2 Bluetooth Low Energy module technical data ....................................................................... 6 4.2.1 Channel List Bluetooth Low Energy ................................................ 6 4.3 Ports identification ................................................................................................................. 7 4.4 Modifications incorporated in E.U.T. ..................................................................................... 7 4.5 Auxiliary equipment ............................................................................................................... 7 5. REFERENCE STANDARDS ................................................................................................... 8 6. OPERATING TEST MODES AND TEST CONDITIONS .............................................................. 8 7. SUMMARY OF TEST RESULTS ............................................................................................. 9 8. UNITS OF MEASUREMENTS ............................................................................................... 9 9. TEST RESULTS .................................................................................................................. 10 PRS LAB S.r.l. Unipersonale Sede operativa e Laboratori di prova Headquarter and Testing lab Via Campagna, 92 I 22020 Faloppio (CO) I Italy Tel. +39 031 3500011 I Fax +39 031 991309 [email protected] I www.primaricerca.it Mod 18_48 rev05 Test Report FCCTR Rapporto di prova - Test report n. FCCTR_181512-1 I Data - Date 28/09/2022 Pagina 3 di 61 0. RELEASE CONTROL RECORD TEST REPORT NUMBER REASON OF CHANGE DATE OF ISSUE FCCTR_181512-0 Original release 21/07/2022 FCCTR_181512-1 Typo error at pag.14 28/09/2022 This document is valid in last revision that deletes and replaces the previous one 1. DECISION RULE PRS LAB specifies that, if the decision rules of conformity of the test results are not indicated in detail in the standard/s object of tests, it takes as a decision rule for the declaration of conformity the simple binary system (w = 0) stated in the ILAC-G8-09:2019 document. The decision rule is applicable for all parts of standard Statements of conformity are reported as: - Pass: the measured value is below the acceptance limit, 퐴퐿=푇퐿. - Fail: the measured value is above the acceptance limit, 퐴퐿=푇퐿. Definitions - Guard Band (w): interval between a tolerance limit and a corresponding acceptance limit where length 푤=|푇퐿−퐴퐿|. - Tolerance Limit (TL) (Specification Limit): specified upper or lower bound of permissi…

Text truncated - open the document above for the full version.

PRS LAB S.r.l. Unipersonale Sede operativa e Laboratori di prova Headquarter and Testing lab Via Campagna, 92 I 22020 Faloppio (CO) I Italy Tel. +39 031 3500011 I Fax +39 031 991309 [email protected] I www.primaricerca.it Mod 18_48 rev05 Test Report FCCTR Rapporto di prova - Test report n. MPETR_181511-0 I Data - Date 25/07/2022 Pagina 1 di 13 RAPPORTO DI PROVA TEST REPORT Rif. / Ref. n. MPETR_181511-0 Data Emissione /Issue Date: 25/07/2022 Pagine / Pages: 13 Scopo delle prove Test object Prove di tipo in accordo alla Norma Type test according to standards FCC Cfr 47 part 2 - §2.1093 Richiedente Applicant Paradox Engineering SA Via Passeggiata 7 – 6883 Novazzano – CH Tel.: +41912330100 Marchio commerciale Trade mark Fabbricante Manufacturer MinabeaMitsumi Inc. 3-9-6 Mita, Minato-ku, Tokyo 108-8330 Tel.: 81-3-6758-6711 Prodotto Product Sub 1-GHz IPv6/6LoWPAN Hardware radio device, compliant within NEMA standard, that operates as: Smart Lighting Node and Gateway for other Nodes Modello Model NDLM007US-1 NDLM007US-2 Identificativo FCC FCC ID 2AKPQNDLM007 Data ricevimento campioni Date of test samples receipt 09/05/2022 Campioni verificati No. of tested samples 2 – Sampled by the applicant Data verifiche Testing date From 23/05/2022 to 26/03/2022 Sito di prova Testing site PRSLAB S.r.l. Unipersonale - Via Campagna 92 - 22020 Faloppio - Como - Italy Identificativo FCC del sito di prova FCC designation number IT0012 Esito delle valutazioni Assessment results CONFORME / COMPLIANT Verifiche effettuate da Verifications carried out by Daniele AOSANI Tecnico Laboratorio Laboratory Engineer Approvato Approved by Riccardo PFEIFFER Responsabile Laboratorio Laboratory Manager I risultati delle prove riportati nel presente rapporto di prova si riferiscono solo ai campioni esaminati. The test results reported in this test report shall refer only to the samples tested. Il campione è stato fornito dal cliente ed i risultati si riferiscono al campione così come ricevuto The sample has been provided by the customer and the results apply to the sample as received Questo Report non può essere riprodotto in modo parziale, salvo espressa autorizzazione scritta da parte del Laboratorio This report may not be partially reproduced, except with the prior written permission of the issuing Laboratory PRS LAB S.r.l. Unipersonale Sede operativa e Laboratori di prova - Headquarter and Testing lab: Via Campagna, 92 I 22020 Faloppio (CO) I Italy Tel. +39 031 3500011 I Fax +39 031 991309 [email protected] I www.primaricerca.it Mod 18_48 rev05 Test Report FCCTR Rapporto di prova - Test report n. MPETR_181511-0 I Data - Date 25/07/2022 Pagina 2 di 13 CONTENUTO TABLE OF CONTENTS 0. RELEASE CONTROL RECORD ..................................................................................................... 3 1. DECISION RULE ........................................................................................................................ 3 2. INFORMATION PROVIDED BY CUSTOMER ................................................................................. 3 3. GENERAL REMARKS ................................................................................................................. 3 4. TECHNICAL INFORMATION OF EQUIPMENT UNDER TEST (EUT) ................................................. 4 4.1 EUT Identification ......................................................................................................................... 4 4.1 Bluetooth Low Energy module technical data .............................................................................. 5 4.2 Radio module technical data ........................................................................................................ 6 4.3 LTE module technical data (model NDLM007US-1) ..................................................................... 7 4.4 LTE module technical data (model NDLM007US-2) ..................................................................... 8 4.5 Ports identification ........................................................................................................................ 9 4.6 Modifications incorporated in E.U.T. ............................................................................................ 9 4.7 Auxiliary equipment ...................................................................................................................... 9 5. REFERENCE STANDARDS ........................................................................................................ 10 6. MEASUREMENTS AND CALCULATION RESULTS ....................................................................... 11 6.1 RF Exposure Conditions .............................................................................................................. 11 6.2 EUT composition ......................................................................................................................... 11 6.3 Calculation method, results and limits ....................................................................................... 12 6.4 Result .......................................................................................................................................... 12 PRS LAB S.r.l. Unipersonale Sede operativa e Laboratori di prova - Headquarter and Testing lab: Via Campagna, 92 I 22020 Faloppio (CO) I Italy Tel. +39 031 3500011 I Fax +39 031 991309 [email protected] I www.primaricerca.it Mod 18_48 rev05 Test Report FCCTR Rapporto di prova - Test report n. MPETR_181511-0 I Data - Date 25/07/2022 Pagina 3 di 13 0. RELEASE CONTROL RECORD TEST REPORT NUMBER REASON OF CHANGE DATE OF ISSUE MPETR_181511-0 Original release 25/07/2022 This document is valid in last revision that deletes and replaces the previous one 1. DECISION RULE PRS LAB specifies that, if the decision rules of conformity of the test results are not indicated in detail in the standard/s object of tests, it takes as a decision rule for the declaration of con…

Text truncated - open the document above for the full version.