2AL5O-LTR05Wireless Remote Control

Wireless Remote Control LTR05 This Product is a Wireless Remote Control, which has two buttons. OPERATION: 1. Press"ON"button on the Remote to power ON outlets 2. Press "OFF" button on the Remote to power OFF outlets. BATTERY INFORMATION AND REPLACEMENT: One CR2032 3-Volt battery included in transmitter. 1. To replace, slide off the battery cover from the back of Remiote Control. Make note of the location of the positive side of the battery. 2. Remove the used battery and insert a new CR2032 3-Volt battery. Confirm that the polarity is correct. When facing the battery compartment from the back of the remote control, the positive side faces up. 3. Slide the cover back. 4. Dispose of old battery properly. WARNING: The remote control is not a toy. Keep batteries and remote control away from children and pets. Follow the battery manufacture safety and usage instructions. Remove battery if product is to be left unused for a long time. Clean the battery contacts and also those of the device prior to battery installation. Do not use as permanent source of power. Do not exceed electrical ratings. ON OFF CAUTION: Please note that changes or modifications of this product is not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.

NINGBO LINSHENG ELECTRIC CO.,LTD. XIAODONG INDUSTRIAL ZONE ,YUYAO CITY,ZHEJIANG,CHINA Request for Confidentiality Date: April 27, 2020 Subject: Confidentiality Request for: ______( FCC ID:2AL5O-LTR05) _____ Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, Section 12.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit ☐ Short Term ☒Permanent Block Diagrams ☐ Short Term External Photos ☐ Short Term ☐Permanent * 1 Internal Photos ☐ Short Term ☒Permanent Operation Description/Theory of Operation ☐ Short Term ☐ Permanent Parts List & Placement/BOM ☐ Short Term ☐ Permanent Tune-Up Procedure ☐ Short Term ☒ Permanent Schematics ☐ Short Term Test Setup Photos ☐ Short Term ☐Permanent * 3 User’s Manual NINGBO LINSHENG ELECTRIC CO.,LTD has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180 ) 2 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: IC currently only distinguishes Per ma nent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, Fangdandan By: __________________________ ________________________ (Signature/Title 3 ) (Print name) 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will beextended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at: https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 -Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

NINGBO LINSHENG ELECTRIC CO.,LTD. XIAODONG INDUSTRIAL ZONE ,YUYAO CITY,ZHEJIANG,CHINA Authority to Act as Agent Date: April 27, 2020 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: Intertek Shanghai is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: Dec 30, 2020 By: __________________________ _______Fangdandan_________________ (Signature 1 ) (Print name) Tit le: _______engineer___________________ On behalf of: ______NINGBO LINSHENG ELECTRIC CO.,LTD____________________ (Company Name) Telephone: _____0574-62593070_____________ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

FCC ID: 2AL5O-LTR05 External Picture

Label & Label Location

FCC ID: 2AL5O-LTR05 Internal Picture Antenna FCC ID: 2AL5O-LTR05

NINGBO LINSHENG ELECTRIC CO.,LTD. RF TEST REPORT Report Type: FCC Part 15.231 & ISED RSS-210 RF report Model: LTR05 REPORT NUMBER: 191102415SHA-001 ISSUE DATE: Jan 16, 2020 DOCUMENT CONTROL NUMBER: TTRF15.231_V1 © 2018 Intertek Intertek Testing Services Shanghai Building No.86, 1198 Qinzhou Road (North) Caohejing Development Zone Shanghai 200233, China Telephone: 86 21 6127 8200 www.intertek.com TEST REPORT This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. TTRF15.231_V1 © 2018 Intertek Page 2 of 29 Report no.: 191102415SHA-001 Applicant: NINGBO LINSHENG ELECTRIC CO.,LTD. XIAODONG INDUSTRIAL ZONE, YUYAO CITY, ZHEJIANG, CHINA Manufacturer: Same as applicant Manufacturing site: Same as applicant FCC ID: 2AL5O-LTR05 SUMMARY: The equipment complies with the requirements according to the following standard(s) or Specification: 47CFR Part 15 (2019): Radio Frequency Devices (Subpart C) ANSI C63.10 (2013): American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices RSS-210 Issue 9 (August 2016): Licence-exempt Radio Apparatus (All Frequency Bands): Category I Equipment RSS-Gen Issue 5 (April 2018): General Requirements for Compliance of Radio Apparatus PREPARED BY: REVIEWED BY: Project Engineer Stephanie Zhang Reviewer Daniel Zhao Report No.: 191102415SHA-001 TEST REPORT TTRF15.231_V1 © 2018 Intertek Page 3 of 29 Content REVISION HISTORY................................................................................................................................................ 4 MEASUREMENT RESULT SUMMARY ..................................................................................................................... 5 1 GENERAL INFORMATION ............................................................................................................................. 6 1.1 DESCRIPTION OF EQUIPMENT UNDER TEST (EUT) ..................................................................................................... 6 1.2 TECHNICAL SPECIFICATION .................................................................................................................................... 6 1.3 DESCRIPTION OF TEST FACILITY .............................................................................................................................. 7 2 TEST SPECIFICATIONS ................................................................................................................................... 8 2.1 STANDARDS OR SPECIFICATION ............................................................................................................................... 8 2.2 MODE OF OPERATION DURING THE TEST ................................................................................................................... 8 2.3 TEST SOFTWARE LIST ............................................................................................................................................ 8 2.4 TEST PERIPHERALS LIST ......................................................................................................................................... 8 2.5 TEST ENVIRONMENT CONDITION: ............................................................................................................................ 9 2.6 INSTRUMENT LIST .............................................................................................................................................. 10 2.7 MEASUREMENT UNCERTAINTY ............................................................................................................................. 11 3 FUNDAMENTAL & SPURIOUS EMISSION & RESTRICT BAND RADIATED EMISSION ...................................... 12 3.1 LIMIT .............................................................................................................................................................. 12 3.2 MEASUREMENT PROCEDURE ............................................................................................................................... 13 3.3 TEST CONFIGURATION ........................................................................................................................................ 14 3.4 TEST RESULTS OF RADIATED EMISSIONS ................................................................................................................. 16 4 POWER LINE CONDUCTED EMISSION ......................................................................................................... 22 4.1 LIMIT .............................................................................................................................................................. 22 4.2 TEST CONFIGURATION ........................................................................................................................................ 22 4.3 MEASUREMENT PROCEDURE ............................................................................................................................... 23 4.4 TEST RESULTS OF POWER LINE CONDUCTED EMISSION............................................................................................... 24 5 EMISSION …

Text truncated - open the document above for the full version.

FCC ID: 2AL5O-LTR05 Test Setup Radiated Emission 30M-1G FCC ID: 2AL5O-LTR05 >1G