2ALMH2SOLO DUAL

[email protected] Melisau 1255, 6863 Egg, Austria DOORS INSTALLATION INSTRUCTIONS 12345678 DRAWERS INSTALLATION INSTRUCTIONS 12345678 9 10+B 10+B SLIDINGDOORS INSTALLATION INSTRUCTIONS 123456 PROGRAMMING INSTALLATION INSTRUCTIONS 123456 TROUBLESHOOTING Lock is open and the keys are not working: • The battery low alarm was activated. • Please insert a new battery. Key is not working: • Is there any sound? If so, please try to activate the key with the programming card. • No sound: Try to find the right position at the furniture. The keys have a higher range if you place them fast at the right point than moving slowly. The programming card does not work: • Do you have a second card? • If not, please unscrew the locks, press the button on the backside and teach the lock the program- ming card again. No sound with any card: • Use a flat iron part (not a screwdriver) and break up the furniture. The rated breaking point at the latch will save the furniture. Motor runs, lock stays locked: • Maybe there is some pressure on the bolt in the lock. • Move the door in all possible directions and try it again. • Press the door in and use your key again. • Adjust the locking devices after such a problem. I lost my key: • Delete all keys with the programming card. • Activate all keys again. SECURITY ADVICE MANUAL >10cm >0,4 Made in AUSTRIAElectronic locks 5 16 H Instalation Video 5 YEARS REPLACE WARRANTY Technical support: +43 699 1333 5155 14 H FCCStatement 1.ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions: (1)Thisdevicemaynotcauseharmfulinterference. (2)Thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesired operation. 2.Changesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidthe user'sauthoritytooperatetheequipment. NOTE: ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuantto Part15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmful interferenceinaresidentialinstallation. Thisequipmentgeneratesusesandcanradiateradiofrequencyenergyand,ifnotinstalledandusedin accordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereis noguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmful interferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,the userisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures: Reorientorrelocatethereceivingantenna. Increasetheseparationbetweentheequipmentandreceiver. Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected. Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

PSGmbH DATE:2021-5-19 FederalCommunicationsCommission Authorization&EvaluationDivision 7345OaklandMillsRoad Columbia,Maryland21046 AuthoritytoActasAgent Onourbehalf,IappointJianyanTestingGroupShenzhenCo.,Ltd.; No.101,Building8, InnovationWisdomPort,No.155HongtianRoad,HuangpuCommunity,XinqiaoStreet,Bao'an District,Shenzhen,Guangdong,People'sRepublicofChina. ,toactasouragentinthe preparationofthisapplicationforequipmentcertification.Icertifythatsubmitted documentsproperlydescribethedeviceorsystemforwhichequipmentcertificationis sought.Ialsocertifythateachunitmanufactured,importedormarketed,asdefinedinthe FederalCommunicationsCommission’sregulationswillhaveaffixedtoitalabel identicaltothatsubmittedforapprovalwiththisapplication. Forinstanceswhereourauthorizedagentsignstheapplicationforcertificationonourbehalf,I acknowledgethatallresponsibilityforcomplyingwiththetermsandconditionsforcertification, asspecifiedbyNemkoCanadaInc,stillresideswithMelisau1255,6863EggAustria Dated this 2021-5-19 By: GuentherSutterluety SignaturePrinted Title: Manager Onbehalfof: PSGmbH Telephone: +436641722900

PSGmbH DATE:2021-5-19 EquipmentAutorisationDivision FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 FCCID:2ALMH2 ProductName:SOLODUAL RequestforConfidentiality PursuanttoSections0.457and0.459ofthecommissionsrules,weherebyrequestthat thefollowingdocumentsbeheldconfidential:  Schematics Blockdiagram Operationdescription  BOM TUNEUP Thesematerialscontaintradesecretsandproprietaryinformationandarenot customarilyreleasedtothepublic.Thepublicdisclosureofthisinformationmightbe harmfultothecompanyandprovideunjustifiedbenefitstoourcompetitors. Dated this 2021-5-19 By: GuentherSutterluety SignaturePrinted Title: manager Onbehalfof:PSGmbH Telephone: +436641722900

Report No: JYTSZB-R01-2100111 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2103015 No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 15 of 21 8 EUT Constructional Details Report No: JYTSZB-R01-2100111 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2103015 No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 16 of 21 Report No: JYTSZB-R01-2100111 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2103015 No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 17 of 21

Location:

Report No: JYTSZB-R01-2100111 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2103015 No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 18 of 21 Report No: JYTSZB-R01-2100111 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2103015 No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 19 of 21 Report No: JYTSZB-R01-2100111 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2103015 No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 20 of 21 Report No: JYTSZB-R01-2100111 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2103015 No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 21 of 21 ------End of report------

JianYan Testing Group Shenzhen Co., Ltd. Report No: JYTSZB-R12-2100392 Authorized Signature: Bruce Zhang Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the JYT product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 1 Cover Page RF Exposure Evaluation Report Applicant: PS GmbH Address of Applicant: Melisau 1255, 6863 Egg Austria Equipment Under Test (EUT) Product Name: SOLO DUAL Model No.: DUAL Trade mark: PS FCC ID: 2ALMH2 Applicable standards: FCC CFR Title 47 Part 2 Subpart J Section 2.1091 Date of sample receipt: 08 Mar., 2021 Date of Test: 08 Mar., to 22 Jun., 2021 Date of report issue: 23 Jun, 2021 Test Result: PASS* Report No: JYTSZB-R12-2100392 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2103015 No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 2 of 7 2 Version Version No. Date Description 00 23 Jun, 2021 Original Tested by: Date: 23 Jun, 2021 Test Engineer Reviewed by: Date: 23 Jun, 2021 Project Engineer Report No: JYTSZB-R12-2100392 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2103015 No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 3 of 7 3 Contents Page 1 COVER PAGE ....................................................................................................................................................... 1 2 VERSION ............................................................................................................................................................... 2 3 CONTENTS ........................................................................................................................................................... 3 4 GENERAL INFORMATION .................................................................................................................................. 4 4.1 CLIENT INFORMATION ........................................................................................................................................... 4 4.2 GENERAL DESCRIPTION OF E.U.T. ...................................................................................................................... 4 4.3 OPERATING MODES .............................................................................................................................................. 4 4.4 ADDITIONS TO, DEVIATIONS, OR EXCLUSIONS FROM THE METHOD ...................................................................... 4 4.5 LABORATORY FACILITY ........................................................................................................................................ 5 4.6 LABORATORY LOCATION ...................................................................................................................................... 5 5 TECHNICAL REQUIREMENTS SPECIFICATION IN FCC CFR TITLE 47 PART 2.1091 ............................ 6 5.1 LIMITS .................................................................................................................................................................... 6 5.2 TEST PROCEDURE ................................................................................................................................................. 6 5.3 RESULT .................................................................................................................................................................. 7 5.4 CONCLUSION ......................................................................................................................................................... 7 Report No: JYTSZB-R12-2100392 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2103015 No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 4 of 7 4 General Information 4.1 Client Information Applicant: PS GmbH Address: Melisau 1255, 6863 Egg Austria Manufacturer/ Factory: PS GmbH Address: Melisau 1255, 6863 Egg Austria 4.2 General Description of E.U.T. Product Name: SOLO DUAL Model No.: DUAL Operation Frequency: BLE: 2402MHz~2480MHz Modulation technology: BLE: GFSK Antenna Type: Internal Antenna Antenna gain: 2.5 dBi(Declared by applicant) Test Sample Condition: The test samples were provided in good working order with no visible defects. 4.3 Operating Modes Operating mode Detail description BLE mode Keep the EUT in continuously transmitting in BLE mode 4.4 Additions to, deviations, or exclusions from the method No Report No: JYTSZB-R12-2100392 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2103015 No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huan…

Text truncated - open the document above for the full version.

JianYan Testing Group Shenzhen Co., Ltd. Report No: JYTSZB-R12-2100390 Authorized Signature: Bruce Zhang Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the JYT product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 1 Cover Page FCC REPORT (BLE) Applicant: PS GmbH Address of Applicant: Melisau 1255, 6863 Egg Austria Equipment Under Test (EUT) Product Name: SOLO DUAL Model No.: DUAL Trade mark: PS FCC ID: 2ALMH2 Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 Date of sample receipt: 08 Mar., 2021 Date of Test: 08 Mar., to 22 Jun., 2021 Date of report issued: 23 Jun, 2021 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. Report No: JYTSZB-R12-2100390 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2103015 No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 2 of 21 2 Version Version No. Date Description 00 23 Jun, 2021 Original Tested by: Date: 23 Jun, 2021 Test Engineer Reviewed by: Date: 23 Jun, 2021 Project Engineer Report No: JYTSZB-R12-2100390 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2103015 No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 3 of 21 3 Contents Page 1 COVER PAGE ....................................................................................................................................................... 1 2 VERSION ............................................................................................................................................................... 2 3 CONTENTS ........................................................................................................................................................... 3 4 TEST SUMMARY .................................................................................................................................................. 4 5 GENERAL INFORMATION .................................................................................................................................. 5 5.1 CLIENT INFORMATION ............................................................................................................................................ 5 5.2 GENERAL DESCRIPTION OF E.U.T. ....................................................................................................................... 5 5.3 TEST ENVIRONMENT AND MODE, AND TEST SAMPLES PLANS ............................................................................... 7 5.4 DESCRIPTION OF SUPPORT UNITS ........................................................................................................................ 7 5.5 MEASUREMENT UNCERTAINTY .............................................................................................................................. 7 5.6 ADDITIONS TO, DEVIATIONS, OR EXCLUSIONS FROM THE METHOD....................................................................... 7 5.7 LABORATORY FACILITY .......................................................................................................................................... 7 5.8 LABORATORY LOCATION ....................................................................................................................................... 7 5.9 TEST INSTRUMENTS LIST ....................................................................................................................................... 8 6 TEST RESULTS AND MEASUREMENT DATA ................................................................................................ 9 6.1 ANTENNA REQUIREMENT: ...................................................................................................................................... 9 6.2 CONDUCTED OUTPUT POWER ............................................................................................................................ 10 6.3 OCCUPY BANDWIDTH .......................................................................................................................................... 11 6.4 POWER SPECTRAL DENSITY ............................................................................................................................... 12 6.5 BAND EDGE ......................................................................................................................................................... 13 6.5.1 Conducted Emission Method...................................................................................................................... 13 6.5.2 Radiated Emission Method ......................................................................................................................... 14 6.6 SPURIOUS EMISSION ..........…

Text truncated - open the document above for the full version.

Königswinkel 10 32825 Blomberg, Germany Phone: +49 (0) 52 35 / 95 00-0 Fax:+49 (0) 52 35 / 95 00-10 [email protected] www.phoenix-testlab.de Test Report Report Number: F181323E2 Equipment under Test (EUT): ANNA-B1 series Applicant: u-blox AG Manufacturer: u-blox AG Examiner:Ruben BRAUNReport Number: F181323E2 Date of Issue: 28.09.2018Order Number: 18-111323Page 2 of 85 References [1] ANSI C63.10-2013, American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices [2] FCC CFR 47 Part 15, Radio Frequency Devices [3] RSS-247 Issue 2 (February 2017), Digital Transmission Systems (DTSs), Frequency Hopping Systems (FHSs) and Licence-Exempt Local Area Network (LE-LAN) Devices [4] RSS-Gen Issue 5 (April 2018), General Requirements for Compliance of Radio Apparatus [5] 508074 D01 DTS Meas Guidance v04 (April 2017), Guidance for performing compliance measurements on transmission systems (DTS) operating under section 15.247 Examiner:Ruben BRAUNReport Number: F181323E2 Date of Issue: 28.09.2018Order Number: 18-111323Page 3 of 85 Test Result The requirements of the tests performed as shown in the overview (clause 4) were fulfilled by the equipment under test. The complete test results are presented in the following. This test report is only valid in its original form. Any reproduction of its contents in extracts without written permission of the accredited test laboratory PHOENIX TESTLAB GmbH is prohibited. The test results herein refer only to the tested sample. PHOENIX TESTLAB GmbH is not responsible for any generalisations or conclusions drawn from these test results concerning further samples. Any modification of the tested samples is prohibited and leads to the invalidity of this test report. Each page necessarily contains the PHOENIX TESTLAB Logo and the TEST REPORT NUMBER. Tested and written by: Ruben BRAUN28.09.2018 Name Signature Date Reviewed and approved by:Bernd STEINER28.09.2018 Name Signature Date Examiner:Ruben BRAUNReport Number: F181323E2 Date of Issue: 28.09.2018Order Number: 18-111323Page 4 of 85 Contents:Page Identification...................................................................................................................................61 1.1Applicant ............................................................................................................................................. 6 1.2Manufacturer ....................................................................................................................................... 6 1.3Test Laboratory ................................................................................................................................... 6 1.4EUT (Equipment under Test) ............................................................................................................... 7 1.5Technical Data of Equipment ............................................................................................................... 8 1.5.1Antenna List................................................................................................................................ 9 1.6Dates .................................................................................................................................................. 9 Operational States .......................................................................................................................102 Additional Information ..................................................................................................................143 Overview ......................................................................................................................................154 Results.........................................................................................................................................165 5.1Duty cycle ......................................................................................................................................... 16 5.1.1Method of measurement ........................................................................................................... 16 5.1.2Test results ............................................................................................................................... 17 5.2Maximum peak output power ............................................................................................................. 18 5.2.1Method of measurement (conducted) ........................................................................................ 18 5.2.1.1Test results (conducted) ................................................................................................... 20 5.2.2Method of measurement (radiated) ........................................................................................... 22 5.2.2.1Test results (radiated) ....................................................................................................... 23 5.3DTS Bandwidth / 99% Bandwidth ...................................................................................................... 25 5.3.1Method of measurement (conducted) ........................................................................................ 25 5.3.1.1Test results (conducted) ................................................................................................... 26 5.4Peak Power Spectral Density ............................................................................................................ 27 5.4.1Method of measurement (conducted) ........................................................................................ 27 5.4.1.1Test results (conducted) ................................................................................................... 28 5.4.2Method of measurement (radiated) ........................................................................................... 30 5.4.2.1Test results (radiated) ........................…

Text truncated - open the document above for the full version.

Report No: JYTSZB-R12-2100390 JianYan Testing Group Shenzhen Co., Ltd. Project No.: JYTSZE2103015 No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Page 20 of 21 7 Test Setup Photo Radiated Spurious Emission Below 1GHz