2ALZSKR210WMAEAccess Control Reader

KR210-WMAE User Manual The KR210-WMAE reader is a RFID proximity card and Bluetooth reader for Kastle access control systems. It is intended to be used in conjunction with an access control board such as a KZDM, KZSRDR, or Axiom Control Board. Notes on Use: • Operating Temp: 0-49 degrees C • Must use 22 AWG or larger with a wire run no longer than 500 ft • All Wiring shall be in accordance with the National Electrical Code, ANSI/NFPA 70 • The Reader is to be mounted in a protected premise To install and use the reader: • Connect the reader wires using wire nuts or beanie wire connectors to the existing wire run coming out of the mounting hole or receptacle box. Make sure to connect all wire by color white to white, green to green, black to black, and red to red. (green with stripes and white with stripes to be used for Wiegand data connections) • Remove the reader backplate. Mount the backplate to the wall / or door frame by securing screws through mounting holes. Push wire bundle back in to mounting hole or receptacle box. Mount the reader to the backplate. • After the reader is terminated and connected on both ends and power is applied, the red LED should blink for 30 seconds and then turn solid blue. FCC: IC: Per RSP-100, Sec 4 - Required Notices to the User Radio/broadcast products shall comply with the requirements to include required notices and/or statements to the user of the product for each unit of the product offered for sale. The required notices shall comply with the following requirement: • The notices shall be as specified in the applicable RSS regulation(s) to the product. • These notices shall be shown in a conspicuous location in the user manual for the product, or to be displayed on the product — variable formats are acceptable for providing the notices (i.e. in paper form, CD, DVD, or insert with download link on the company’s website). • If more than one notice is required for multiple product versions, the product version to which each notice pertains should be identified. • The suppliers of radio equipment shall provide the notices and/or statements in both English and French. • In cases where the user notifications are only available in one language (English or French) at the time of the certification process, the applicant shall provide a declaration in writing that the user notices and/or statements to the user of the product will be in both English and French when the product is for sale and/or lease in Canada. FCC Part 15.19 Warning Statement- (Required for all Part 15 devices) THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. FCC Part 15.21 Warning Statement NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. FCC Part 15.105(b) Warning Statement- (ONLY Required for 15.109-JBP devices) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. IC RSS-GEN, Sec 8.4 Warning Statement- (Required for license-exempt devices) ENGLISH: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. FRENCH: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. RF Exposure Statement: The device has been evaluated to meet the general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Test Report# TR_24037-25_FCC 15.247 SC_ Revision: 2 Te s t Report - FCC Par t 15.247 Spot-Check Applicant: Kastle Systems International Signature: Name & Title: Tim Royer, Lab Manager Date of Signature 10/16/2025 Signature: Name & Title: Kristoffer Costa, EMC Technician Date of Signature 10/16/2025 This test report relates only to the items tested as identified and is not valid for any subsequent changes or modifications made to the equipment under test. 13146 NW 86 th Drive, Suite 400, Alachua, Florida 32615 (352) 472-5500 / [email protected] Page 2 of 16 This test report shall not be reproduced except in full without the written and signed permission of IIA Lab Services LLC. a subsidiary of Industrial Inspection & Analysis, Inc. (“IIA”) Table of Contents 1. APPLICANT INFORMATION ........................................................................................................................................................................... 3 1.1 TEST RESULT SUMMARY ............................................................................................................................................................................................ 3 2. LOCATION OF TESTING ................................................................................................................................................................................. 4 2.1 TEST LABORATORY ....................................................................................................................................................................................................4 3. TEST SAMPLE(S) (EUT/DUT) ........................................................................................................................................................................... 4 3.1 DESCRIPTION OF THE EUT ........................................................................................................................................................................................ 5 3.2 CONFIGURATION OF EUT ......................................................................................................................................................................................... 6 3.3 TEST SETUP OF EUT .................................................................................................................................................................................................. 6 4. TEST METHODS & APPLICABLE REGULATORY LIMITS ............................................................................................................................ 7 4.1 TEST METHODS/STANDARDS/GUIDANCE: ............................................................................................................................................................... 7 4.2 APPLIED LIMITS AND REGULATORY LIMITS: .............................................................................................................................................................. 7 5. MEASUREMENT UNCERTAINTY .................................................................................................................................................................... 7 6. ENVIRONMENTAL CONDITIONS ................................................................................................................................................................. 7 6.1 TEMPERATURE & HUMIDITY ...................................................................................................................................................................................... 7 7. LIST OF TEST EQUIPMENT AND TEST FACILITY ........................................................................................................................................ 8 7.1 LIST OF TEST EQUIPMENT ......................................................................................................................................................................................... 8 8. TEST RESULTS ................................................................................................................................................................................................... 9 8.1 BAND-EDGE MEASUREMENTS ................................................................................................................................................................................. 10 8.1.1 Lower Band Edge Plot, Stopped, 2402 MHz .................................................................................................................................... 11 8.2 RADIATED EMISSIONS.............................................................................................................................................................................................. 12 8.2.1 Radiated Emissions, 2602 MHz .......................................................................................................................................................... 13 8.2.2 Radiated Emissions, 2426 MHz .......................................................................................................................................................... 14 9. ANNEX-B – TEST SETUP PHOTOGRAPHS ................................................................................................................................................ 15 10. HISTORY OF TEST REPORT CHANGES ...................................................................................................................................................... 15 13146 NW 86 th Drive, Suite 400, Alachua, Florida 32615 (352) 472-5500 / [email protected] Page 3 of 16 This test report shall not be reproduced except in full without the written and signed permission of IIA Lab Services LLC. a subsidiary of Industrial Inspection & Analysis, Inc. (“IIA”) 1. Applicant Information Applicant: Kastle Systems International Address: 6402 Arlington Blvd…

Text truncated - open the document above for the full version.

Test Report# TR_24037-25_ KR210-A _FCC 1.1310_MPE_Simultaneous Transmission_ Revision: 2 Test Report - FCC Part 1.1310 / MPE Simultaneous Transmission Applicant: Kastle Systems International Signature: Name & Title: Tim Royer, Lab Manager Date of Signature 12/19/2025 Signature: Name & Title: Kristoffer Costa, EMC Technician Date of Signature 12/19/2025 This test report relates only to the items tested as identified and is not valid for any subsequent changes or modifications made to the equipment under test. 13146 NW 86 th Drive, Suite 400, Alachua, Florida 32615 (352) 472-5500 / [email protected] Page 2 of 8 This test report shall not be reproduced except in full without the written and signed permission of IIA Lab Services LLC. a subsidiary of Industrial Inspection & Analysis, Inc. (“IIA”) Table of Contents 1. APPLICANT INFORMATION ........................................................................................................................................................................... 3 2. LOCATION OF TESTING ................................................................................................................................................................................. 3 2.1 TEST LABORATORY ...................................................................................................................................................................... 3 3. TEST SAMPLE(S) (EUT/DUT) ........................................................................................................................................................................... 3 3.1 DESCRIPTION OF THE EUT .......................................................................................................................................................... 4 4. TEST METHODS & APPLICABLE REGULATORY LIMITS ............................................................................................................................ 5 5. RF EXPOSURE RESULTS .................................................................................................................................................................................. 6 6. HISTORY OF TEST REPORT CHANGES ........................................................................................................................................................ 7 13146 NW 86 th Drive, Suite 400, Alachua, Florida 32615 (352) 472-5500 / [email protected] Page 3 of 8 This test report shall not be reproduced except in full without the written and signed permission of IIA Lab Services LLC. a subsidiary of Industrial Inspection & Analysis, Inc. (“IIA”) 1. Applicant Information Applicant: Kastle Systems International Address: 6402 Arlington Blvd. Falls Church, Virginia, 22042, United States 2. Location of Testing 2.1 Test Laboratory IIA Lab Services LLC. is a subsidiary of Industrial Inspection & Analysis, Inc. (“IIA”). Testing was performed at IIA’s permanent laboratory located at 13146 NW 86 th Drive, Suite 400, Alachua, Florida 32615. FCC test firm # 578780 FCC Designation # US1070 FCC site registration is under A2LA certificate # 0955.01 ISED Canada test site registration # 2056A EU Notified Body # 1177 For all designations see A2LA scope # 0955.01 3. Test Sample(s) (EUT/DUT) The test sample was received: 10/3/2025 Dates of Testing: 10/9/2025 – 10/16/2025 13146 NW 86 th Drive, Suite 400, Alachua, Florida 32615 (352) 472-5500 / [email protected] Page 4 of 8 This test report shall not be reproduced except in full without the written and signed permission of IIA Lab Services LLC. a subsidiary of Industrial Inspection & Analysis, Inc. (“IIA”) 3.1 Description of the EUT A description as well as unambiguous identification of the EUT(s) tested. Where more than one sample is required for technical reasons (such as the use of connected units for the purpose of conducted output power testing where the product units will have integral antennas), each specific test shall identify which unit was tested. Identification FCC ID: 2ALZSKR210WMAE Certified Module FCC ID: QOQ-GM240P Brief Description Access Control Reader Model(s) # KR210-A Firmware version 2.2.0 Software version 2.2.0 Serial Number N/A Technical Characteristics Frequency Range 2402 MHz- 2483.5 MHz RF O/P Power (Max.) 8 dBm Modulation FM Bandwidth & Emission Class N/A Number of Channels N/A Duty Cycle 100% Antenna Connector Internal Voltage Rating (AC or Batt.) 12VDC Antenna Characteristics Antenna Frequency Range Mode / BW Antenna Gain 1 n/a n/a 0 dBi - Note: Information such as antenna gain, firmware/software numbers are provided by the manufacturer and cannot be validated by the test lab. 13146 NW 86 th Drive, Suite 400, Alachua, Florida 32615 (352) 472-5500 / [email protected] Page 5 of 8 This test report shall not be reproduced except in full without the written and signed permission of IIA Lab Services LLC. a subsidiary of Industrial Inspection & Analysis, Inc. (“IIA”) 4. Test methods & Applicable Regulatory Limits SAR EXCLUSION CALCULATION: Section 4.3.1 General SAR test exclusion guidance Equation: RSS 102 Issue 6 Section 6.3 Exemption Limits for Routine Evaluation Equation: 13146 NW 86 th Drive, Suite 400, Alachua, Florida 32615 (352) 472-5500 / [email protected] Page 6 of 8 This test report shall not be reproduced except in full without the written and signed permission of IIA Lab Services LLC. a subsidiary of Industrial Inspection & Analysis, Inc. (“IIA”) 1. RF Exposure Results Power Density = 0.00003774 mW/cm 2 Power Density = 0.0000000000319 mW/cm 2 Per KDB 447498 D01 General RF Exposure Guidance v06 Sec 7.2. Equation: (TX1 MPE/MPE Limit 1 + TX2MPE/MPE Limit 2) Frequency Power Density at separation distance Limit MPE Ratio Limit 2400-2483.5 & 13.56 MHz 0.00003774 mW/cm2 0.2 mW/cm2 1 ≤1 Fre que nc y Band E val uat i on D i st anc e ( c m ) M ax Pow e r + T ol e ranc e ( dBm ) Ant e nna G ai n ( dBi ) D ut y Cyc l e ( %) E IRP ( W ) …

Text truncated - open the document above for the full version.

Date: 23 December 2025 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 alt � KASTLE Subject: Manufacturer Attestation of RF Output Power Limitation This letter is provided to clarify the transmit power for the Bluetooth module BGM240PB, bearing FCC ID: QOQ-GM240P, which is integrated into our product with FCC ID: 2ALZSKR210WMAE. The RF output power of this module is firmware controlled and permanently limited. The maximum conducted output power is restricted to +8 dBm by firmware and cannot be increased by the end user, integrator, or through any software configuration accessible outside of the manufacturer's controlled firmware. This firmware-based power limitation ensures continued compliance with FCC regulations under all normal operating conditions. Any modification to the firmware that affects RF parameters can only be performed by the manufacturer and would require re-evaluation for FCC compliance. Sincerely, Jaimie Crafton Senior Systems Engineer

Test Report# TR_24037-25_FCC 15.247 SC_ Revision: 2 Te s t Report - FCC Par t 15.247 Spot-Check Applicant: Kastle Systems International Signature: Name & Title: Tim Royer, Lab Manager Date of Signature 10/17/2025 Signature: Name & Title: Kristoffer Costa, EMC Technician Date of Signature 10/17/2025 This test report relates only to the items tested as identified and is not valid for any subsequent changes or modifications made to the equipment under test. 13146 NW 86 th Drive, Suite 400, Alachua, Florida 32615 (352) 472-5500 / [email protected] Page 2 of 16 This test report shall not be reproduced except in full without the written and signed permission of IIA Lab Services LLC. a subsidiary of Industrial Inspection & Analysis, Inc. (“IIA”) Table of Contents 1. APPLICANT INFORMATION ........................................................................................................................................................................... 3 1.1 TEST RESULT SUMMARY ............................................................................................................................................................................................ 3 2. LOCATION OF TESTING ................................................................................................................................................................................. 4 2.1 TEST LABORATORY ....................................................................................................................................................................................................4 3. TEST SAMPLE(S) (EUT/DUT) ........................................................................................................................................................................... 4 3.1 DESCRIPTION OF THE EUT ........................................................................................................................................................................................ 5 3.2 CONFIGURATION OF EUT ......................................................................................................................................................................................... 6 3.3 TEST SETUP OF EUT .................................................................................................................................................................................................. 6 4. TEST METHODS & APPLICABLE REGULATORY LIMITS ............................................................................................................................ 7 4.1 TEST METHODS/STANDARDS/GUIDANCE: ............................................................................................................................................................... 7 4.2 APPLIED LIMITS AND REGULATORY LIMITS: .............................................................................................................................................................. 7 5. MEASUREMENT UNCERTAINTY .................................................................................................................................................................... 7 6. ENVIRONMENTAL CONDITIONS ................................................................................................................................................................. 7 6.1 TEMPERATURE & HUMIDITY ...................................................................................................................................................................................... 7 7. LIST OF TEST EQUIPMENT AND TEST FACILITY ........................................................................................................................................ 8 7.1 LIST OF TEST EQUIPMENT ......................................................................................................................................................................................... 8 8. TEST RESULTS ................................................................................................................................................................................................... 9 8.1 BAND-EDGE MEASUREMENTS ................................................................................................................................................................................. 10 8.1.1 Lower Band Edge Plot, Stopped, 2402 MHz .................................................................................................................................... 11 8.2 RADIATED EMISSIONS.............................................................................................................................................................................................. 12 8.2.1 Radiated Emissions, 2402 MHz .......................................................................................................................................................... 13 8.2.2 Radiated Emissions, 2426 MHz .......................................................................................................................................................... 14 9. ANNEX-B – TEST SETUP PHOTOGRAPHS ................................................................................................................................................ 15 10. HISTORY OF TEST REPORT CHANGES ...................................................................................................................................................... 15 13146 NW 86 th Drive, Suite 400, Alachua, Florida 32615 (352) 472-5500 / [email protected] Page 3 of 16 This test report shall not be reproduced except in full without the written and signed permission of IIA Lab Services LLC. a subsidiary of Industrial Inspection & Analysis, Inc. (“IIA”) 1. Applicant Information Applicant: Kastle Systems International Address: 6402 Arlington Blvd…

Text truncated - open the document above for the full version.

Test Report# TR_24037-25_FCC 15.209_ Revision: 2 Te s t Report – FCC Par t 15.209 Unintentional Radiator Applicant: Kastle Systems International Signature: Name & Title: Tim Royer, Lab Manager Date of Signature 10/17/2025 Signature: Name & Title: Kristoffer Costa, EMC Technician Date of Signature 10/17/2025 This test report relates only to the items tested as identified and is not valid for any subsequent changes or modifications made to the equipment under test. 13146 NW 86 th Drive, Suite 400, Alachua, Florida 32615 (352) 472-5500 / [email protected] Page 2 of 24 This test report shall not be reproduced except in full without the written and signed permission of Timco Engineering Inc., a subsidiary of Industrial Inspection & Analysis, Inc. (IIA). Table of Contents 1. APPLICANT INFORMATION ........................................................................................................................................................................... 3 1.1 TEST RESULT SUMMARY ............................................................................................................................................................................................ 3 2. LOCATION OF TESTING ................................................................................................................................................................................. 4 2.1 TEST LABORATORY ....................................................................................................................................................................................................4 3. TEST SAMPLE(S) (EUT/DUT) ........................................................................................................................................................................... 4 3.1 DESCRIPTION OF THE EUT ........................................................................................................................................................................................ 5 3.2 CONFIGURATION OF EUT ......................................................................................................................................................................................... 6 3.3 TEST SETUP OF EUT .................................................................................................................................................................................................. 6 4. TEST METHODS & APPLICABLE REGULATORY LIMITS ............................................................................................................................ 7 4.1 TEST METHODS/STANDARDS/GUIDANCE ................................................................................................................................................................ 7 5. MEASUREMENT UNCERTAINTY .................................................................................................................................................................... 7 6. ENVIRONMENTAL CONDITIONS ................................................................................................................................................................. 7 7. LIST OF TEST EQUIPMENT AND TEST FACILITY ........................................................................................................................................ 8 8. TEST RESULTS ................................................................................................................................................................................................... 9 8.1 RADIATED EMISSIONS.............................................................................................................................................................................................. 10 8.1.1 125 kHz, 10 kHz to 30 MHz Plot......................................................................................................................................................... 11 8.1.2 125 kHz, 10 kHz to 30 MHz Table ..................................................................................................................................................... 12 8.1.3 125 kHz, 30 MHz to 200 MHz, Horizontal/ Vertical Polarity Plot ............................................................................................. 13 8.1.4 125 kHz, 30 MHz to 200 MHz, Horizontal/ Vertical Polarity Table .......................................................................................... 14 8.1.5 125 kHz, 200 MHz to 1000 MHz, Horizontal/ Vertical Polarity Plot ......................................................................................... 15 8.1.6 125 kHz, 200 MHz to 1000 MHz, Horizontal/ Vertical Polarity Table ...................................................................................... 16 8.1.1 13.56 MHz, 10 kHz to 30 MHz Plot ................................................................................................................................................... 17 8.1.2 13.56 MHz, 10 kHz to 30 MHz Table ................................................................................................................................................ 18 8.1.3 13.56 MHz, 30 MHz to 200 MHz, Horizontal/ Vertical Polarity Plot........................................................................................ 19 8.1.4 13.56 MHz, 30 MHz to 200 MHz, Horizontal/ Vertical Polarity Table ................................................................................... 20 8.1.5 13.56 MHz, 200 MHz to 1000 MHz, Horizontal/ Vertical Polarity Plot ................................................................................... 21 8.1.6 13.56 MHz, 200 MHz to 1000 MHz, Horizontal/ Verti…

Text truncated - open the document above for the full version.